A Single-Branch Third-Order Pole–Zero Low-Pass Filter With 0.014- $\hbox{mm}^{2}$ Die Size and 0.8-kHz (1.25-nW) to 0.94-GHz (3.99-mW) Bandwidth–Power Scalability

2013 ◽  
Vol 60 (11) ◽  
pp. 761-765 ◽  
Author(s):  
Yong Chen ◽  
Pui-In Mak ◽  
Stefano D'Amico ◽  
Li Zhang ◽  
He Qian ◽  
...  
Keyword(s):  
Third Order ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Order Pole ◽  
Low Pass ◽  
Single Branch

A modified Bessel filter for amplitude demodulation of respiratory electromyograms

1998 ◽  
Vol 84 (1) ◽  
pp. 378-388 ◽  
Author(s):  
Ronald S. Platt ◽  
Eric A. Hajduk ◽  
Manuel Hulliger ◽  
Paul A. Easton
Keyword(s):  
High Frequency ◽  
Stop Band ◽  
Pass Band ◽  
Third Order ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Transient Characteristics ◽  
Low Pass ◽  
Seventh Order ◽  
Frequency Components

Platt, Ronald S., Eric A. Hajduk, Manuel Hulliger, and Paul A. Easton. A modified Bessel filter for amplitude demodulation of respiratory electromyograms. J. Appl. Physiol. 84(1): 378–388, 1998.—We studied a device that is commonly used for amplitude demodulation of respiratory muscle electromyograms (EMG). This device contains a rectifier and a low-pass filter called a modified third-order Paynter filter. We characterized this filter and found that it has good transient characteristics that suit its task as an EMG demodulator, but it has poor high-frequency attenuation that passes interfering, higher frequency components to the output waveform. Therefore, we designed and constructed a new filter with transient characteristics that are comparable to those of the modified Paynter filter but with superior high-frequency attenuation. This new filter is a modified seventh-order Bessel filter. We also identified a simple technique to convert an existing modified Paynter filter back to an original Paynter filter. The original Paynter filter has a wider pass band than the modified Paynter filter but superior stop-band attenuation.

Study on the Frequency Compensation of the Dynamic Unbalance Signal Extraction for General Hard Bearing Dynamic Balancing Machine

2017 ◽  
Vol 870 ◽  
pp. 173-178 ◽  
Author(s):  
Ru Qin ◽  
Ping Cai ◽  
Ding Ding Zhao ◽  
Yi Gao
Keyword(s):  
Field Experiments ◽  
Measuring System ◽  
Measuring Error ◽  
Frequency Compensation ◽  
Dynamic Balancing ◽  
Third Order ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Rotating Speed ◽  
Low Pass

When a dynamic balancing measuring system is equipped with velocity sensor as its vibration pick-up, the output signal of the sensor is proportional to the third power of rotating speed of the balancing operation. Generally a third order low-pass filter circuit is often used to eliminate the influence of rotating speed and suppress the high frequency interference as well. However, the frequency response of third order low-pass filter circuit can’t compensate completely for the response characteristic of the vibration system of balancing machine, which then causes measuring error. So, as a general purpose hard bearing dynamic balancing machine being suitable for a wide speed range, frequency compensation must be conducted. The approach of frequency compensation is classified into two broad types: hardware and software compensation. This paper conducts further research on these two methods to improve the accuracy of the measuring system and proves the accuracy and effectiveness of the two methods by signal simulation and field experiments.

scholarly journals Damping techniques for grid-connected converters with LCL filter: an overview

2021 ◽  
Vol 42 (2) ◽  
pp. 227
Author(s):  
Arthur de Abreu Romão ◽  
Newton Da Silva
Keyword(s):  
Renewable Energy Sources ◽  
Design Procedure ◽  
Voltage Source ◽  
Third Order ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Resonant Behavior ◽  
Low Pass ◽  
Grid Connected Converters ◽  
Low Pass Filters

Distributed generation systems, based on renewable energy sources, are typically connected to the main grid by a voltage-source inverter with a low-pass filter. The need for improved efficiency led to the use of third order low-pass filters, such as the LCL configuration, which has resonant behavior. In order to meet energy quality requirements and ensure the systems stability it is necessary to suppress the LCL filters resonance through damping techniques. Therefore, this paper presents an overview of some damping strategies found in literature and its design procedure, applied to a simulated single-phase grid-tied inverter. The comparison of each presented damping methodology characteristics is described, with analysis of advantages and drawbacks for each case.

Current mode MOSFET-only third order Butterworth low pass filter with DTMOS tuning technique

2016 ◽  
Vol 89 (3) ◽  
pp. 645-654 ◽  
Author(s):  
Atilla Uygur ◽  
Bilgin Metin ◽  
Hakan Kuntman ◽  
Oguzhan Cicekoglu
Keyword(s):  
Current Mode ◽  
Third Order ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Low Pass

Electronically Tunable Current-Mode Third-Order Square-Root-Domain Filter Design

2018 ◽  
Vol 27 (09) ◽  
pp. 1850136
Author(s):  
Ali Kircay ◽  
M. Serhat Keserlioglu ◽  
F. Zuhal Adalar
Keyword(s):  
Filter Design ◽  
Current Mode ◽  
Cmos Process ◽  
Square Root ◽  
Third Order ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Low Pass ◽  
Level 3 ◽  
Electronically Tunable

In this study, electronically-tunable, current-mode, square-root-domain, third-order low-pass filter is proposed. The study is carried out with three circuit designs. First circuit is third-order low-pass Butterworth filter, second circuit is third-order low-pass Chebyshev filter and the last circuit is third-order low-pass elliptic filter. All the input and output values of the filter circuit are current. Only grounded capacitors and MOSFETs are required in order to realize the filter circuit. Additionally, natural frequency [Formula: see text] of the current-mode filter can be adjusted electronically using outer current sources. To validate the theory and to demonstrate the performance of third-order filter, frequency and time domain simulations of PSPICE program are used. To that end, TSMC 0.35[Formula: see text][Formula: see text]m Level 3 CMOS process parameters are utilized to realize the simulations of the filter.

Sign in / Sign up

Export Citation Format

Share Document