Phase-based direct average strain estimation for elastography

Author(s):  
Sharmin Ara ◽  
Faisal Mohsin ◽  
Farzana Alam ◽  
Sharmin Rupa ◽  
Soo Lee ◽  
...  
Ultrasonics ◽  
2014 ◽  
Vol 54 (1) ◽  
pp. 137-146 ◽  
Author(s):  
Mohammad Arafat Hussain ◽  
Farzana Alam ◽  
Sharmin Akhtar Rupa ◽  
Rayhana Awwal ◽  
Soo Yeol Lee ◽  
...  

Author(s):  
Bo Wang ◽  
Chen Sun ◽  
Keming Zhang ◽  
Jubing Chen

Abstract As a representative type of outlier, the abnormal data in displacement measurement often inevitably occurred in full-field optical metrology and significantly affected the further evaluation, especially when calculating the strain field by differencing the displacement. In this study, an outlier removal method is proposed which can recognize and remove the abnormal data in optically measured displacement field. A iterative critical factor least squares algorithm (CFLS) is developed which distinguishes the distance between the data points and the least square plane to identify the outliers. A successive boundary point algorithm is proposed to divide the measurement domain to improve the applicability and effectiveness of the CFLS algorithm. The feasibility and precision of the proposed method are discussed in detail through simulations and experiments. Results show that the outliers are reliably recognized and the precision of the strain estimation is highly improved by using these methods.


2017 ◽  
Vol 40 (2) ◽  
pp. 67-83 ◽  
Author(s):  
Catarina Carvalho ◽  
Pieter Slagmolen ◽  
Stijn Bogaerts ◽  
Lennart Scheys ◽  
Jan D’hooge ◽  
...  

2016 ◽  
Vol 676 ◽  
pp. 606-612 ◽  
Author(s):  
Kamal A. Aly ◽  
N.M. Khalil ◽  
Yousif Algamal ◽  
Qaid M.A. Saleem

Author(s):  
Kimihiro Toh ◽  
Shunsuke Maeda ◽  
Takao Yoshikawa

In order to obtain the non-linear average stress-average strain relationships (σ-ε curves) of damaged structural members under both tensile and compressive loads, the systematical calculations are performed using the non-linear FE analysis (FEA) code, LS-DYNA, and the idealized σ-ε curves of damaged structural members are estimated from FEA results. In addition, by introducing the idealized σ-ε curves of damaged structural members to the simplified calculation program, which is developed by authors and based on the Smith’s method, the residual ultimate strength of damaged hull structures is calculated. The residual ultimate strength of damaged hull structures is also calculated utilizing FEA, the calculation results by the simplified calculation program are compared with the results obtained from FE analyses so as to examine the accuracy of simplified calculation method.


2014 ◽  
Vol 57 (2) ◽  
Author(s):  
Shoja Ansari ◽  
Ahmad Zamani

<p>In this paper the short-term seismic deformation of Iran is determined by the earthquake moment tensor summation. The study areas include the Alborz, Kopeh-Dagh, eastern Iran, Makran and Zagros orogenic belts. The spatial distribution and focal mechanisms of the earthquakes delineate the deformation zones. The mean directions of the P and T axes are determined by the equal area projection of the seismic moment tensors. The orientations of the P-axes are dominantly correlated with the NE crustal motion of Iran relative to Eurasia. The average strain rates are calculated in all of the regions. The maximum shear strain and dilatation rates are defined by the eigenvalues of the average strain rate tensors. The dilatation rate indicates that not only the dominant compression but also the subsidiary tension affects the Alborz and Makran orogenic belts. The velocity tensor components discriminate the vertical thickening and thinning of the crust in some regions of Iran. The seismic deformation rates, which are determined by the velocity tensors, are smaller than the geodetic deformation rates. In the high seismic deformation zones, such as the eastern Iran and Alborz, the geodetic deformation rate is comparable with the seismic deformation rate. Our results indicate that the NW Zagros and Kopeh-Dagh have the lowest seismic deformation rates. The seismic shortening rate increases from NW to SE in the Zagros orogenic belt. The seismic deformation orientations are different from the P-axes, probably due to the lateral translation. The maximum percentage of the seismic deformation in the study areas is related to the eastern Iran and the minimum one is related to the Makran orgenic belt. The average shape tensors indicate that the focal mechanisms in the Kopeh-Dagh have the highest internal similarity. The eastern Iran has the largest seismic moment rate, while the central Zagros has the lowest one.</p>


Author(s):  
Corey D. Hernandez ◽  
Thomas S. Gates ◽  
Seun K. Kahng

This paper presents recent results on research of achieving multifunctional structures utilizing Carbon Nanotube (CNT) yarns. The investigation centers on creating composite structures with CNT yarns to simultaneously achieve increases in mechanical strength and the ability to sense strain. The CNT yarns used in our experiments are of the single-ply and two-ply variety with the single-ply yarns having diameters on the order of 10–20 μm. The yarns are embedded in silicon rubber and polyurethane test specimens. Mechanical tests show an increase in modulus of elasticity, with an additional weight increase of far less than one-percent. Sensing characteristics of the yarns are investigated on stainless steel test beams in an electrical bridge configuration, and are observed to have a strain sensitivity of 0.7mV/V/1000 micro-strain. Also reported are measurements of the average strain distribution along the direction of the CNT yarns on square silicon rubber membranes.


Sign in / Sign up

Export Citation Format

Share Document