Analysis of Hub Motor Configuration and Battery Placement on Ride Comfort of Electric Trucks

2019 ◽  
Author(s):  
Suganthan Suriyamoorthy ◽  
Sidhanth Gupta ◽  
Deepak Prakash Kumar ◽  
Shankar C. Subramanian
Keyword(s):  
Ride Comfort

Techniques for Determining the Parameters of a Two-Dimensional Tire Model for the Study of Ride Comfort

1997 ◽  
Vol 25 (3) ◽  
pp. 187-213 ◽  
Author(s):  
F. Mancosu ◽  
G. Matrascia ◽  
F. Cheli
Keyword(s):  
Physical Properties ◽  
Ride Comfort ◽  
Dynamic Test ◽  
Longitudinal Direction ◽  
Tire Model ◽  
Rigid Ring ◽  
Ring Model ◽  
Mass Moment ◽  
A New Technique ◽  
And Performance

Abstract A rigid ring model of the tire for the study of in-plane dynamics and a new technique for determining the parameters of the model are presented in this paper. This model can be used for studying the comfort of vehicles, problems of driving, and braking problems in the longitudinal direction. Comparison with finite element models shows that the rigid ring model of the tire is capable of describing the in-plane eigenmode shapes in the frequency range of 0–130 Hz. The well-known “brush model,” integrated into the tire model, is introduced to take into account the slide phenomena in the contact patch. The parameters of the model can be correlated with the physical properties of the tire so that designers can take advantage of such a correlation in the development of new tires in terms of time, cost, and performance. The technique used to determine the parameters of the model for some automobile tires include the direct measurements of some physical properties (mass, moment of inertia, stiffness) and a method of identification applied on the results from a dynamic test. The model is able to predict experimental data in terms of natural frequencies and relative dampings. Results from the application of this technique on two tires are reported.

scholarly journals Research on Model Predictive Control for Automobile Active Tilt Based on Active Suspension

Energies ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 671
Author(s):  
Jialing Yao ◽  
Meng Wang ◽  
Zhihong Li ◽  
Yunyi Jia
Keyword(s):  
Load Transfer ◽  
Ride Comfort ◽  
Active Suspension ◽  
Path Tracking ◽  
Roll Angle ◽  
Lateral Acceleration ◽  
Vehicle Speed ◽  
Model Predictive Controller ◽  
Advantages And Disadvantages ◽  
Predictive Controller

To improve the handling stability of automobiles and reduce the odds of rollover, active or semi-active suspension systems are usually used to control the roll of a vehicle. However, these kinds of control systems often take a zero-roll-angle as the control target and have a limited effect on improving the performance of the vehicle when turning. Tilt control, which actively controls the vehicle to tilt inward during a curve, greatly benefits the comprehensive performance of a vehicle when it is cornering. After analyzing the advantages and disadvantages of the tilt control strategies for narrow commuter vehicles by combining the structure and dynamic characteristics of automobiles, a direct tilt control (DTC) strategy was determined to be more suitable for automobiles. A model predictive controller for the DTC strategy was designed based on an active suspension. This allowed the reverse tilt to cause the moment generated by gravity to offset that generated by the centrifugal force, thereby significantly improving the handling stability, ride comfort, vehicle speed, and rollover prevention. The model predictive controller simultaneously tracked the desired tilt angle and yaw rate, achieving path tracking while improving the anti-rollover capability of the vehicle. Simulations of step-steering input and double-lane change maneuvers were performed. The results showed that, compared with traditional zero-roll-angle control, the proposed tilt control greatly reduced the occupant’s perceived lateral acceleration and the lateral load transfer ratio when the vehicle turned and exhibited a good path-tracking performance.

Design of combined brake system for light weight scooters

2021 ◽  
pp. 095440702110240
Author(s):  
Yuan-Ting Lin ◽  
Chyuan-Yow Tseng ◽  
Jao-Hwa Kuang ◽  
Yeong-Maw Hwang
Keyword(s):  
Ride Comfort ◽  
Brake System ◽  
Force Distribution ◽  
Test Results ◽  
Systematic Method ◽  
Braking Performance ◽  
Evaluation Indexes ◽  
Low Costs ◽  
Braking Force ◽  
Good Agreement

The combined brake system (CBS) is a mechanism that links the front and rear brakes for scooters. For two-wheeled scooters, a CBS with appropriate braking force distribution can reduce the risk of crashing accidents due to insufficient driving proficiency. The design of the braking force distribution for a CBS is challenging to the designer because it has to fulfill many requirements such as braking performance, ride comfort, reliability, and low costs. This paper proposes a systematic method to optimize the parameters of CBS. The evaluation indexes for the design are first discussed. The steps to determine the critical parameter to meet the indexes and a method to predict braking performance are developed. Finally, driving tests are carried out to verify the effectiveness of the proposed method. Experimental results showed that the deceleration of the tested scooter equipped with the designed CBS achieves an average mean fully developed deceleration (MFDD) of 5.246 m/s2, higher than the homologation requirement. Furthermore, the proposed method’s prediction of braking performance is in good agreement with the test results, with errors <1%.

Comprehensive Analysis for Influence of Controllable Damper Time Delay on Semi-Active Suspension Control Strategies

2017 ◽  
Vol 139 (3) ◽  
Author(s):  
Yechen Qin ◽  
Feng Zhao ◽  
Zhenfeng Wang ◽  
Liang Gu ◽  
Mingming Dong
Keyword(s):  
Time Delay ◽  
Dynamic Characteristics ◽  
Ride Comfort ◽  
Hybrid Control ◽  
Sliding Mode ◽  
Control Strategies ◽  
Active Suspension ◽  
Test System ◽  
Suspension Control ◽  
Simulation Results

This paper presents a comprehensive comparison and analysis for the effect of time delay on the five most representative semi-active suspension control strategies, and refers to four unsolved problems related to semi-active suspension performance and delay mechanism that existed. Dynamic characteristics of a commercially available continuous damping control (CDC) damper were first studied, and a material test system (MTS) load frame was used to depict the velocity-force map for a CDC damper. Both inverse and boundary models were developed to determine dynamic characteristics of the damper. In addition, in order for an improper damper delay of the form t+τ to be corrected, a delay mechanism of controllable damper was discussed in detail. Numerical simulation for five control strategies, i.e., modified skyhook control SC, hybrid control (HC), COC, model reference sliding mode control (MRSMC), and integrated error neuro control (IENC), with three different time delays: 5 ms, 10 ms, and 15 ms was performed. Simulation results displayed that by changing control weights/variables, performance of all five control strategies varied from being ride comfort oriented to being road handling oriented. Furthermore, increase in delay time resulted in deterioration of both ride comfort and road handling. Specifically, ride comfort was affected more than road handling. The answers to all four questions were finally provided according to simulation results.

Sign in / Sign up

Export Citation Format

Share Document