The Effect of Synthetic Silica on Ultrafiltration PSf Membrane

2013 ◽  
Vol 65 (4) ◽  
Author(s):  
Zawati Harun ◽  
Mohd Riduan Jamalludin ◽  
Hatijah Basri ◽  
Muhamad Fikri Shohur ◽  
Nurafiqah Rosman ◽  
...  
Keyword(s):  
Pure Water ◽  
Water Flux ◽  
Inversion Method ◽  
X Ray Diffraction ◽  
Weight Percentage ◽  
Pure Water Flux ◽  
Dope Solution ◽  
And Performance ◽  
Polyethelene Glycol ◽  
Phase Inversion Method

This study investigates the effects of synthetic silica(SiO2)with different weight percentage concentrations on the morphology and performance of the polysulfone (PSf) and polyethelene glycol (PEG) based membrane ultrafiltration (UF). Phase inversion method was used to prepare PSf/PEG ultrafiltration (UF) flatsheet membrane. SiO2 and N-Methyl 2 Pyrrolidone (NMP) were used as an additive and solvent respectively. The fabricated membrane was characterized by scanning electron microscope (SEM), X-ray diffraction (XRD) and the performances of the membranes were measured in term of pure water flux by using distilled water and solute rejection at different wastewater concentration at 50%, 75% and 87.5%. The result showed that the addition of 2% silica in the dope solution increased the permeation in terms pure water flux and the best rejection with 62 Lm-2 h-1 and 89% (at 87.5 % waste water dilution) respectively

The Preparation and Performance Characteristics of Polyvinyl Chloride-co-Vinyl Acetate (VC-Co-VAc-OH) Modified Membranes on the Non-Woven Fabrics

2012 ◽  
Vol 562-564 ◽  
pp. 3-6
Author(s):  
Jing Zhang ◽  
Zhan Wang ◽  
Xiao Ye ◽  
Wen Juan Li ◽  
Long Yue Shi ◽  
...  
Keyword(s):  
Pure Water ◽  
Water Flux ◽  
Woven Fabrics ◽  
Inversion Method ◽  
Evaporation Time ◽  
Preparation Conditions ◽  
Pure Water Flux ◽  
And Performance ◽  
Phase Inversion Method ◽  
Good Retention

VC-co-VAc-OH material was used to prepare flat-sheet membranes on the non-woven fabrics via phase inversion method. And the membrane preparation conditions（polymer content, the content of additive, environmental temperature, relative humidity, evaporation time, coagulation temperature, coagulation time, immersing time of non-woven fabrics in solvent, and exposure time of non-woven fabrics in air）were discussed systemically by orthogonal method. Finally, the membrane prepared under the optimum condition showe higher pure water flux (287.9 ml•cm-2•h-1) and good retention of Bovine serum albumin (BSA) (87.4 %).

scholarly journals Synthesizing Ag/PDA/PES Antibacterial Membrane for Natural Organic Molecules Removal

2018 ◽  
Vol 65 ◽  
pp. 05023 ◽  
Author(s):  
Kok Poh Wai ◽  
Chai Hoon Koo ◽  
Yean Ling Pang ◽  
Woon Chan Chong ◽  
Woei Jye Lau
Keyword(s):  
Membrane Surface ◽  
Pure Water ◽  
Water Flux ◽  
X Ray Diffraction ◽  
X Ray ◽  
Membrane Performance ◽  
Dope Solution ◽  
And Performance ◽  
Pes Membrane ◽  
Contact Angle Analysis

Silver nanoparticles (NP) was successfully immobilized on polydopamine (PDA) supported polyethersulfone (PES) membrane via a redox reaction. Polyvinylpyrrolidone (PVP) was added into membrane dope solution as a pore-forming agent. Four pieces of membranes (M1, M2, M3 and M4) were fabricated with different active layer coatings to compare their morphological and performance properties. The differences between each sample were highlighted as follow: M1 (pristine PES), M2 (PES+PVP), M3 (PDA/PES+PVP) and M4 (Ag/PDA/PES+PVP). All membranes were characterized using scanning electron microscopy, energy dispersive X-ray spectroscopy, Fourier-transform infrared spectroscopy, X-ray diffraction and contact angle analysis. The membrane performance was examined using pure water permeability (PWP) test, antibacterial test and humic acid (HA) rejection test. Pristine M1 membrane showed that PWP of 27.16 LMH/bar and HA rejection of 84 %. In this study, it was found that the addition of PVP as a pore agent into the membrane M2 increased water flux but slightly deteriorated HA rejection. Coating of PDA on M3 and immobilizing silver NP on M4 membrane surface have improved HA rejection but compromised PWP. The results showed that membrane M4 carried excellent antibacterial property and highest HA rejection among all fabricated membranes.

Influence of Inorganic Additives on the Performance of Polysulfone Ultrafiltration Membrane

2013 ◽  
Vol 65 (4) ◽  
Author(s):  
Muhamad Zaini Yunos ◽  
Zawati Harun ◽  
Hatijah Basri ◽  
Mohd Fikri Shohur ◽  
Mohd Riduan Jamalludin ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Zinc Oxide ◽  
Pure Water ◽  
Water Flux ◽  
Antibacterial Properties ◽  
Ultrafiltration Membrane ◽  
Inversion Method ◽  
Pure Water Flux ◽  
Phase Inversion Method ◽  
Oxide Membrane

The influence of zinc oxide and silver (I) oxide in polysulfone ultrafiltration membrane was studied. The membranes were prepared via phase inversion method. The morphology, surface roughness, hydrophillicity and antibacterial properties of membrane were investigated using SEM, AFM and contact angle device consecutively. It was found that membrane with zinc oxide additive has excellent pure water flux as compared to silver (I) oxide. However silver (I) oxide has better humic acid rejection due to the tradeoff effect. SEM-EDX for PSf/silver (I) oxide reveals that the accumulation of silver on top area in cross section of membrane while for zinc oxide seems more concentrated on the bottom. Interestingly, the AFM results support the previous result when PSf/zinc oxide showed better surface roughness on the top of the membrane. Eventhough zinc oxide is known one of antibacterial material, however from qualitative experiment using disc diffusion test (e-coli), there is no inhibition ring for PSf/zinc oxide membrane as compared to membrane with PSf/silver (I) oxide membrane which shows excellence inhibition ring.

Hydrophilic modification of PVDF membranes by in situ synthesis of nano-Ag with nano-ZrO2

2021 ◽  
Vol 10 (1) ◽  
pp. 538-546
Author(s):  
Yanjun Lu ◽  
Yuxuan Ma ◽  
Tong Yang ◽  
Jifeng Guo
Keyword(s):  
Polyvinylidene Fluoride ◽  
Pure Water ◽  
Water Flux ◽  
Inversion Method ◽  
Hydrophilic Modification ◽  
E Coli ◽  
Pure Water Flux ◽  
Modified Membrane ◽  
Phase Inversion Method

Abstract Modified polyvinylidene fluoride (PVDF) membranes were prepared by the phase inversion method via blending in situ formed nanosilver (Ag) and nanozirconium dioxide (ZrO2). Scanning electron microscopy of the membranes revealed that the surface pore size of the membranes was increased and distributed widely with the addition of modified nanosilver (Ag) and nanozirconium dioxide (ZrO2). The pores of the membrane were reduced due to excessive modification of the material when the content of zirconium dioxide was increased to 0.4%. XRD characterization showed that in situ synthesis of nanosilver (Ag) and nanozirconium dioxide (ZrO2) had been successfully blended in the membranes. The contact angle of the modified membrane ranged from 82.72° to 67.37°, which showed that the hydrophilic properties of the membrane were improved. The pure water flux of the modified membrane increased from 28.43 to 143.2 L/m2 h, indicating that the hydrophilicity of the modified membrane was enhanced significantly. The flux recovery rate of the modified membrane was obviously increased in the fouling experiment with BSA as the source of organic pollutants. The antimicrobial contamination of the membrane was greatly enhanced with the E. coli microbial contamination experiment.

Effect of PVP Hydrophilic Additive on the Morphology and Properties of PVDF Porous Membranes

2014 ◽  
Vol 981 ◽  
pp. 891-894 ◽  
Author(s):  
Yun Wei Guo ◽  
Wei Wei Cui ◽  
Wen Hua Xu ◽  
Yang Jiang ◽  
Hui Hui Liu ◽  
...  
Keyword(s):  
Vinylidene Fluoride ◽  
Pure Water ◽  
Water Flux ◽  
Porous Membrane ◽  
Porous Membranes ◽  
Inversion Method ◽  
Water Contact ◽  
Poly Vinylidene Fluoride ◽  
Pure Water Flux ◽  
Phase Inversion Method

This work describes the preparation and the properties of poly(vinylidene fluoride) (PVDF) porous membranes. The porous membrane was prepared using phase-inversion method by adding hydrophilic polyvinylpyrrolidone (PVP) as hole-agent. The contrastive analysis of membrane characterizations between the membrane no PVP added and the membrane added PVP were carried out by optical microscopy analysis, scanning electron microscopy, porosity, pure water flux and water contact angle. The results showed that adding PVP can induce the building of pore structure, increase the surface roughness and hydrophilicity of PVDF membrane, and then enhance its pure water flux.

Effect of PVP content and polymer concentration on polyetherimide (PEI) and polyacrylonitrile (PAN) based ultrafiltration membrane fabrication and characterization

2018 ◽  
Vol 2017 (2) ◽  
pp. 329-339 ◽  
Author(s):  
Sevgi Güneş-Durak ◽  
Türkan Ormancı-Acar ◽  
Neşe Tüfekci
Keyword(s):  
Pure Water ◽  
Polymer Concentration ◽  
Water Flux ◽  
Inversion Method ◽  
Membrane Thickness ◽  
Average Roughness ◽  
Membrane Performance ◽  
Membrane Fabrication ◽  
Pure Water Flux ◽  
Phase Inversion Method

Abstract In this study, four different membranes were fabricated by using polyetherimide and polyacrylonitrile polymers, N-methyl-2-pyrrolidone and polyvinylpyrrolidone (PVP) via phase inversion method to improve the membrane performance in fruit juice wastewater (FJWW) treatment. The addition of PVP to the casting solution increased membrane hydrophilicity, water content, contact angle, porosity, Fourier transform infrared spectroscopy peaks, membrane thickness, average roughness and viscosity of cast solutions compared to the bare membrane. It can be said that the addition of a lower polymer concentration and PVP intensively increases the pure water flux of the membrane. However, as the flux increased, a small decrease in FJWW rejection was observed.

scholarly journals Influence of Polymer Concentration on Membrane Performance in Wastewater Treatment

2018 ◽  
Vol 55 (1) ◽  
pp. 95-98 ◽  
Author(s):  
Laurentia Geanina Tiron ◽  
Stefan Catalin Pintilie ◽  
Andreea Liliana Lazar ◽  
Maria Vlad ◽  
Stefan Balta ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Pure Water ◽  
Polymer Concentration ◽  
Water Flux ◽  
Inversion Method ◽  
Membrane Performance ◽  
Treatment Technologies ◽  
Pure Water Flux ◽  
Angle Method ◽  
Phase Inversion Method

Water is an important element of life, while every industry in its processes uses an important amount of water. Following processes, the water is contaminated and requires water treatment technologies. Unconventional methods to wastewater treatment, in the last years, use membrane technology as one of the most reliable processes for contaminants removal. In this article, the influence of the different concentrations of polysulfone (PSf) on the polymeric membranes properties was studied. These membranes were obtained through phase inversion method and with different polymer concentrations: 23, 25, 27 and 30 wt.%. The performance of the membranes was studied by pure water flux, permeability and retention. It has been observed that by increasing the polymer concentration, the pure water flux and the permeability will decrease. Retention was determined using methylene blue, which is one of the most utilized dye from industry and it could be observed that by increasing the polymer concentration the retention degree of the pollutant also increases. In order to explain the evolution of membrane permeability at different polymer concentrations, surface hydrophilicity by contact angle method and cross-section SEM imaging were used.

THE FEASIBILITY OF KAOLIN AS MAIN MATERIAL FOR LOW COST POROUS CERAMIC HOLLOW FIBRE MEMBRANE PREPARED USING COMBINED PHASE INVERSION AND SINTERING TECHNIQUE

2017 ◽  
Vol 79 (1-2) ◽  
Author(s):  
Siti Khadijah Hubadillah ◽  
Mohd Hafiz Dzarfan Othman ◽  
A. F. Ismail ◽  
Mukhlis A. Rahman ◽  
Juhana Jaafar
Keyword(s):  
Phase Inversion ◽  
Low Cost ◽  
Pure Water ◽  
Porous Ceramic ◽  
Water Flux ◽  
Hollow Fibre ◽  
Hollow Fibre Membrane ◽  
Fibre Membrane ◽  
Pure Water Flux ◽  
And Performance

Ceramic hollow fibre membrane (CHFM) demonstrated superior characteristics and performance in any separation application. The only problem associated with this kind of technology is the high cost. In order to effectively fabricate and produce low cost porous CHFM, a series of CHFMs made of kaolin were fabricated via combined phase inversion and sintering technique. The CHFMs from kaolin named as kaolin hollow fibre membranes (KHFMs) were studied at different kaolin contents of 35 wt.%, 37.5 wt.% and 40 wt.% sintered at 1200ºC. The result indicated that by varying kaolin contents, different morphologies were obtained due to changes in the viscosity of ceramic suspension containing kaolin. The optimum kaolin content for KHFM was identified. It was found that KHFM prepared at 37.5 wt% has a mechanical strength and pure water flux of A and B respectively.  

scholarly journals The influences of polydopamine immersion time on characteristics and performance of polyvinylidene fluoride ultrafiltration membrane

2018 ◽  
Vol 197 ◽  
pp. 09007
Author(s):  
Syawaliah Syawaliah ◽  
Nasrul Arahman ◽  
Medyan Riza ◽  
Sri Mulyati
Keyword(s):  
Polyvinylidene Fluoride ◽  
Water Flux ◽  
Sem Analysis ◽  
Inversion Method ◽  
Asymmetric Structure ◽  
Pvdf Membrane ◽  
Before And After ◽  
Poly Ethylene ◽  
And Performance ◽  
Phase Inversion Method

The Polyvinylidene Fluoride (PVDF) membrane has been prepared by phase inversion method using N,N-dimethylacetamide (DMAc) as solvent and Poly Ethylene Glycol (PEG) as additive. The fabricated membrane was modified by Polydopamine (PDA) coating in concentration of 0.5 mg/ml and immersion times of 2 hours, 6 hours, and 24 hours. The characteristics and performance of the PVDF membranes before and after the modification are studied in this paper. The result of the water flux experiment showed that the PDA-coated PVDF membranes showcased a higher flux than that of pure PVDF membrane. Scanning Electron Microscopy (SEM) analysis confirmed that the membrane had an asymmetric structure consisting of two layers. There was no significant influence on the addition of PDA to the morphology of the pore matrix because the modification was done by surface coating. Fourier Transform Infrared Spectroscopy (FTIR) analysis showed that PDA was successfully introduced on the surface of PVDF membrane with the appearance of O-H from cathecol and N-H peaks at wavenumber range of 3300-3600 cm-1. Modification with PDA increased the mechanical strength of the membrane which affirmed by the results of the tensile and elongation at break evaluation.

Preparation and Performance of Polysulfone Hollow Fiber Ultrafiltration Membranes

2013 ◽  
Vol 457-458 ◽  
pp. 309-312 ◽  
Author(s):  
Yang Bai ◽  
Zhen Liu ◽  
Dao Bao Sun
Keyword(s):  
Hollow Fiber ◽  
High Performance ◽  
Pure Water ◽  
Water Flux ◽  
Bath Temperature ◽  
Coagulation Bath ◽  
Membrane Structures ◽  
Ultrafiltration Membranes ◽  
Pure Water Flux ◽  
And Performance

Polysulfone (PSF) hollow fiber ultrafiltration membranes were successfully prepared by dry-wet spinning technology. Dimethylacetamide (DMAC) was used as a solvent, water was used as bore liquid and coagulation bath, polyvinylpyrrolidone (PVP) was used as polymeric additive. The effects of spinning conditions on membrane structures and properties were investigated in present study. The results indicated that with the increase of PVP concentration, pure water flux increased and developed finger-like pores were formed. High coagulation bath temperature restricted pure water flux, 30°C was the best for the preparation of high-performance ultrafiltration membranes. When the air length was 11cm, the membrane comprehensive performance was the best.

Sign in / Sign up

Export Citation Format

Share Document