BIOMECHANICAL BEHAVIOUR OF BOVINE SKIN: AN EXPERIMENT-THEORY INTEGRATION AND FINITE ELEMENT SIMULATION

2015 ◽  
Vol 76 (10) ◽  
Author(s):  
Nor Fazli Adull Manan ◽  
Jamaluddin Mahmud ◽  
Aidah Jumahat
Keyword(s):  
Finite Element ◽  
Finite Element Simulation ◽  
Deformation Behaviour ◽  
Element Model ◽  
Tensile Tests ◽  
Theory Integration ◽  
Element Simulation ◽  
Knowledge Enhancement ◽  
First Time

This paper for the first time attempts to establish the biomechanical characteristics of bovine skin via experiment-theory integration and finite element simulation. 30 specimens prepared from fresh slaughtered bovine were uniaxially stretched in-vitro using tensile tests machine. The experimental raw data are then input into a Matlab programme, which quantified the hyperelastic parameters based on Ogden constitutive equation. It is found that the Ogden coefficient and exponent for bovine skin are μ = 0.017 MPa and α = 11.049 respectively. For comparison of results, the quantified Ogden parameters are then input into a simple but robust finite element model, which is developed to replicate the experimental setup and simulate the deformation of the bovine skin. Results from experiment-theory integration and finite element simulation are compared. It is found that the stress-stretch curves are close to one another. The results and finding prove that the current study is significant and has contributed to knowledge enhancement about the deformation behaviour of bovine skin.

Finite Element Simulation of Tire-Rim Interface

1989 ◽  
Vol 17 (4) ◽  
pp. 305-325 ◽  
Author(s):  
N. T. Tseng ◽  
R. G. Pelle ◽  
J. P. Chang
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Finite Element Simulation ◽  
Contact Pressure ◽  
Element Model ◽  
Experimental Measurements ◽  
Inflation Pressure ◽  
Interference Fit ◽  
Element Simulation ◽  
Rubber Composite

Abstract A finite element model was developed to simulate the tire-rim interface. Elastomers were modeled by nonlinear incompressible elements, whereas plies were simulated by cord-rubber composite elements. Gap elements were used to simulate the opening between tire and rim at zero inflation pressure. This opening closed when the inflation pressure was increased gradually. The predicted distribution of contact pressure at the tire-rim interface agreed very well with the available experimental measurements. Several variations of the tire-rim interference fit were analyzed.

3D Finite Element Simulation for Turning of Hardened 45 Steel

2019 ◽  
Vol 13 (2) ◽  
pp. 181-188
Author(s):  
Meng Liu ◽  
Guohe Li ◽  
Xueli Zhao ◽  
Xiaole Qi ◽  
Shanshan Zhao
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Cutting Force ◽  
Finite Element Simulation ◽  
Orthogonal Experiment ◽  
Element Model ◽  
3D Finite Element ◽  
Element Simulation ◽  
Metal Machining ◽  
Single Factor Experiment

Background: Finite element simulation has become an important method for the mechanism research of metal machining in recent years. Objective: To study the cutting mechanism of hardened 45 steel (45HRC), and improve the processing efficiency and quality. Methods: A 3D oblique finite element model of traditional turning of hardened 45 steel based on ABAQUS was established in this paper. The feasibility of the finite element model was verified by experiment, and the influence of cutting parameters on cutting force was predicted by single factor experiment and orthogonal experiment based on simulation. Finally, the empirical formula of cutting force was fitted by MATLAB. Besides, a lot of patents on 3D finite element simulation for metal machining were studied. Results: The results show that the 3D oblique finite element model can predict three direction cutting force, the 3D chip shape, and other variables of metal machining and the prediction errors of three direction cutting force are 5%, 9.02%, and 8.56%. The results of single factor experiment and orthogonal experiment are in good agreement with similar research, which shows that the model can meet the needs for engineering application. Besides, the empirical formula and the prediction results of cutting force are helpful for the parameters optimization and tool design. Conclusion: A 3D oblique finite element model of traditional turning of hardened 45 steel is established, based on ABAQUS, and the validation is carried out by comparing with experiment.

scholarly journals Analysis of Vertical Stiffness of Air Spring Based on Finite Element Method

2018 ◽  
Vol 153 ◽  
pp. 06006
Author(s):  
Jiatong Ye ◽  
Hua Huang ◽  
Chenchen He ◽  
Guangyuan Liu
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Finite Element Simulation ◽  
Element Model ◽  
Simulation Method ◽  
Bench Test ◽  
Air Spring ◽  
Vertical Stiffness ◽  
Element Simulation ◽  
Element Method

In this paper, a finite element model of membrane air spring in the vehicle is established, and its vertical stiffness characteristics under a certain inflation pressure are analysed. The result of finite element simulation method is compared with the result of the air spring bench test. The accuracy and reliability of the finite element simulation method in nonlinear analysis of air spring system are verified. In addition, according to the finite element method, the influence of the installation of the air spring limit sleeve on its stiffness is verified.

Finite element simulation of folding carton erection failure

2007 ◽  
Vol 221 (7) ◽  
pp. 753-767 ◽  
Author(s):  
D M Sirkett ◽  
B J Hicks ◽  
C Berry ◽  
G Mullineux ◽  
A J Medland
Keyword(s):  
Finite Element ◽  
Material Properties ◽  
High Speed ◽  
Element Model ◽  
Machine Material ◽  
Linear Elastic ◽  
Element Simulation ◽  
Packaging Industry ◽  
First Time ◽  
The Eu

In response to recent European Union (EU) regulations on packaging waste, the packaging industry requires greater fundamental understanding of the machine-material interactions that take place during packaging operations. Such an understanding is necessary to handle thinner lighter-weight materials, specify the material properties required for successful processing and design right-first-time machinery. The folding carton industry, in particular, has been affected by the new legislation and needs to realize the potential of computational tools for simulating the behaviour of packaging materials and generating the necessary understanding. This paper describes the creation and validation of a detailed finite element model of a carton during a common packaging operation. The model is applied here to address the problem of carton buckling. The carton was modelled using a linear elastic material definition with non-linear crease behaviour. Air inrush suction, which is believed to cause buckling, was quantified experimentally and incorporated using contact damping interactions. The results of the simulation are validated against high-speed video of carton production. The model successfully predicts the pattern of deformation of the carton during buckling and its increasing magnitude with production rate. The model can be applied to study the effects of variation in material properties, pack properties and machine settings. Such studies will improve responsiveness to change and will ultimately allow end-users to use thinner, lighter-weight materials in accordance with the EU regulations.

Finite element simulation of the deformation of corrugated food cans during sterilization

1990 ◽  
Vol 25 (1) ◽  
pp. 43-49
Author(s):  
K-Y Yuan ◽  
C-C Liang
Keyword(s):  
Finite Element ◽  
Finite Element Simulation ◽  
Deformation Behaviour ◽  
Plastic State ◽  
Elastic Plastic ◽  
Element Simulation ◽  
Incremental Formulation ◽  
Typical Food ◽  
Sterilization Process ◽  
Updated Lagrangian

During the sterilization process of a typical food can, the geometric non-linear and elastic-plastic state is confronted. A derived procedure of updated lagrangian incremental formulation is proposed to simulate the deformation behaviour of the food can. The process is illustrated with a real example. Some interesting results can be noted wherein.

Research on the Connection Performance of Variable Pitch of Screw Threaded Casing Based on 3D Finite Element Simulation Model

2012 ◽  
Vol 215-216 ◽  
pp. 1105-1110 ◽  
Author(s):  
Xiong Guo ◽  
Lv Long Zou ◽  
Bing Lu ◽  
Shi Liang Zhang ◽  
Xing Ren Su ◽  
...  
Keyword(s):  
Finite Element ◽  
Stress Distribution ◽  
Finite Element Simulation ◽  
Element Model ◽  
Static Structure ◽  
3D Finite Element ◽  
Variable Pitch ◽  
Element Simulation ◽  
Ansys Workbench

The connection performance of the large taper, multi-thread, variable pitch of screw threaded casing is researched by 3D finite element simulation on ANSYS Workbench. The 3D finite element model is created precisely. The stress distribution on the teeth of three kind variable pitch of screw threaded structure is studied by using the static structure of the contact analysis module. Contrasting stress distribution of the variable pitch of screw with of the equal pitch of screw under the same working condition, it is validated that design principle for the variable pitch of screw connection is correct. The influence of changes in the amount of variable pitch of screw to the whole stress distribution on teeth is discussed. The results show that the force distribution on the teeth of the variable pitch of screw connection is more uniform than equal pitch of screw, and will improve the overall carrying capacity. This study has its practical value to improve the connective performance of the threaded casing and enhance the product quality of threaded casing.

The Analysis of the Stiffness about the School Bus Based on Hyper Mesh

2014 ◽  
Vol 912-914 ◽  
pp. 806-809
Author(s):  
Ming Feng Zheng ◽  
Yue Chen ◽  
Ya Lin Yan
Keyword(s):  
Finite Element ◽  
Stress Concentration ◽  
Finite Element Model ◽  
Finite Element Simulation ◽  
Local Structure ◽  
Element Model ◽  
School Bus ◽  
Element Simulation ◽  
As Stress

Established a finite element model of the school bus based on the Hyper Mesh, take a finite element simulation about the various parts of the school bus parameters such as stress, displacement and deformation under 5 conditions. Through the analysis of the school bus to identify conditions displacement of stress more concentrated area as well as in operation, by optimizing improve the local structure of these regions,improve the stress concentration and safety.

Sign in / Sign up

Export Citation Format

Share Document