OPTIMAL OFF POINT DETERMINATION IN ELECTRICAL POWER DISTRIBUTION SYSTEM USING RISK ASSESSMENT

2016 ◽  
Vol 78 (6-2) ◽  
Author(s):  
Ahmad Zaidi Abdullah ◽  
Noor Hasnizam Hanafi ◽  
Nurhafiza Azizan ◽  
Mohammad Harith Amlus
Keyword(s):  
Power Distribution ◽  
Distribution System ◽  
Distribution Systems ◽  
Electrical Power ◽  
Normal Operation ◽  
Risk Allocation ◽  
Power Distribution Systems ◽  
Power Distribution System ◽  
Efficiency Measures ◽  
Actual Field

In normal operation of distribution systems, protection systems are important for reliability and efficiency measures. For reliability enhancement of primary loop distribution systems, off points are normally located in midway between substations. Off point in networks allow the continued supply of electric to customer during faults as the feeder is separated into two sections, between two substations. Once a fault is cleared, then the faulted section can be reconfigured to accept supply from the unfaulted section. This is known as load restoration in network distribution system. Currently, off points are allocated using load flows and based on the engineer’s experience. However this method does not optimize the reliability to customers, as it does not take into account the risk allocation to customers. To overcome this, the research proposed a risk-based analysis, which can determine an optimal off point location. The analysis used a real network between PMU Kota Setar and PMU Kota Sarang Semut, Kedah, Malaysia. Actual field data from varying utilities were used for completion of this project. Six scenarios were developed to get a clear view of the total impact of risk with varying locations of off point. It is shown that the method proposed in this project gives a better indication for the optimal determination off point in electrical power distribution systems compared to the commonly used method.

A New Digital Down Conductor Detection Scheme for Overhead Electrical Power Distribution Systems

2011 ◽  
Vol 12 (5) ◽  
Author(s):  
Bhavesh Bhalja ◽  
Pragnesh Shah ◽  
Balubhai Rakholia ◽  
Jignesh Shah
Keyword(s):  
Power Distribution ◽  
Distribution System ◽  
Distribution Systems ◽  
Electrical Power ◽  
Positive Sequence ◽  
Power Distribution Systems ◽  
Detection Scheme ◽  
Power Distribution System ◽  
Protection Devices ◽  
Negative Sequence Current

Detection of down conductor faults in an overhead electrical power distribution system is extremely difficult by the conventional over current protection devices. This paper presents a new digital down conductor detection scheme which is based on the combination (AND logic) of the ratio of the negative sequence current to the positive sequence current and the value of under current during an actual down conductor condition. Real time implementation of the proposed scheme has been carried out on an existing Indian 11 kV, 3 –Phase, 50 Hz power distribution system with the help of digital over current relay. At the end, a comparative evaluation of the proposed scheme with the scheme modeled in PSCAD/EMTDC software package is also presented. Both practical and simulation results indicate the effectiveness of the proposed scheme.

scholarly journals Complete power distribution system representation and state determination for fault location

DYNA ◽  
2015 ◽  
Vol 82 (192) ◽  
pp. 141-149 ◽  
Author(s):  
Andres Felipe Panesso-Hernández ◽  
Juan Mora-Flórez ◽  
Sandra Pérez-Londoño
Keyword(s):  
Power Distribution ◽  
Distribution System ◽  
Distribution Systems ◽  
Fault Location ◽  
Estimation Error ◽  
Distance Estimation ◽  
Power Distribution Systems ◽  
Line Load ◽  
Power Distribution System ◽  
Line Section

<p>The impedance-based approaches for fault location in power distribution systems determine a faulted line section. Next, these require of the estimation of the voltages and currents at one or both section line ends to exactly determine the fault location. It is a challenge because in most of the power distribution systems, measurements are only available at the main substation.  This document presents a modeling proposal of the power distribution system and an easy implementation method to estimate the voltages and currents at the faulted line section, using the measurements at the main substation, the line, load, transformer parameters and other serial and shunt connected devices and the power system topology. The approach here proposed is tested using a fault locator based on superimposed components, where the distance estimation error is lower than 1.5% in all of the cases. </p>

scholarly journals Active Reduction of Short-Circuit Current in Power Distribution Systems

Energies ◽  
2020 ◽  
Vol 13 (2) ◽  
pp. 334
Author(s):  
Esteban Pulido ◽  
Luis Morán ◽  
Felipe Villarroel ◽  
José Silva
Keyword(s):  
Power Distribution ◽  
Distribution System ◽  
Distribution Systems ◽  
Short Circuit ◽  
Circuit Breaker ◽  
Short Circuit Current ◽  
Power Converter ◽  
Power Distribution Systems ◽  
Power Distribution System ◽  
In Series

In this paper, a new concept of short-circuit current (SCC) reduction for power distribution systems is presented and analyzed. Conventional fault current limiters (FCLs) are connected in series with a circuit breaker (CB) that is required to limit the short-circuit current. Instead, the proposed scheme consisted of the parallel connection of a current-controlled power converter to the same bus intended to reduce the amplitude of the short-circuit current. This power converter was controlled to absorb a percentage of the short-circuit current from the bus to reduce the amplitude of the short-circuit current. The proposed active short-circuit current reduction scheme was implemented with a cascaded H-bridge power converter and tested by simulation in a 13.2 kV industrial power distribution system for three-phase faults, showing the effectiveness of the short-circuit current attenuation in reducing the maximum current requirement in all circuit breakers connected to the same bus. The paper also presents the design characteristics of the power converter and its associated control scheme.

scholarly journals Flexibility Enhancement in an Islanded Distribution Power System by Online Demand-Side Management

2019 ◽  
Vol 217 ◽  
pp. 01020 ◽  
Author(s):  
Margarita Chulyukova ◽  
Nikolai Voropai
Keyword(s):  
Power System ◽  
Power Distribution ◽  
Distribution System ◽  
Distribution Systems ◽  
Load Shedding ◽  
Load Management ◽  
Daily Maximum ◽  
Power Distribution Systems ◽  
Power Distribution System ◽  
Islanded Operation

The paper considers the possibilities of increasing the flexibility of power distribution systems by real-time load management. The principles of the implementation of special automatic systems for this purpose are proposed. These systems enable some loads of specific consumers of the power distribution system switched to islanded operation to “shift” from the daily maximum to the minimum, which makes some generators available to connect certain essential consumers disconnected earlier by under-frequency load shedding system to the power system. The approach under consideration is illustrated by a power system with distributed generation.

Shunt Petersen-Coil with Resistor for Single Phase Fault Detection in Resonant Grounded Power Distribution Systems

2013 ◽  
Vol 860-863 ◽  
pp. 2007-2012 ◽  
Author(s):  
Xiao Meng ◽  
Neng Ling Tai ◽  
Yan Hu ◽  
Xia Yang
Keyword(s):  
Power Distribution ◽  
Distribution System ◽  
Distribution Systems ◽  
Single Phase ◽  
Detection Sensitivity ◽  
Power Distribution Systems ◽  
Power Distribution System ◽  
Multi Level ◽  
The Difference ◽  
Petersen Coil

The failure current in resonant grounder power distribution system is small, so it is difficult to detect the fault feeder. This passage presents the equivalent circuit of resonant grounded system, and discusses the difference of electrical characteristics between faulty feeder and sound feeders by using shunt resistors. To reduce the influence of shunt resistors on the system and improve the detection sensitivity, it presents the method of shunting multi-level resistors, and it proves the sensitivity and reliability of this method by EMTP simulation.

scholarly journals An Encoding Technique for Multiobjective Evolutionary Algorithms Applied to Power Distribution System Reconfiguration

2014 ◽  
Vol 2014 ◽  
pp. 1-9 ◽  
Author(s):  
J. L. Guardado ◽  
F. Rivas-Davalos ◽  
J. Torres ◽  
S. Maximov ◽  
E. Melgoza
Keyword(s):  
Evolutionary Algorithms ◽  
Power Distribution ◽  
Distribution System ◽  
Distribution Systems ◽  
Pareto Optimal ◽  
Pareto Optimal Solutions ◽  
Optimal Solutions ◽  
Power Distribution Systems ◽  
Encoding Scheme ◽  
Power Distribution System

Network reconfiguration is an alternative to reduce power losses and optimize the operation of power distribution systems. In this paper, an encoding scheme for evolutionary algorithms is proposed in order to search efficiently for the Pareto-optimal solutions during the reconfiguration of power distribution systems considering multiobjective optimization. The encoding scheme is based on the edge window decoder (EWD) technique, which was embedded in the Strength Pareto Evolutionary Algorithm 2 (SPEA2) and the Nondominated Sorting Genetic Algorithm II (NSGA-II). The effectiveness of the encoding scheme was proved by solving a test problem for which the true Pareto-optimal solutions are known in advance. In order to prove the practicability of the encoding scheme, a real distribution system was used to find the near Pareto-optimal solutions for different objective functions to optimize.

scholarly journals Probability-Based Customizable Modeling and Simulation of Protective Devices in Power Distribution Systems

Energies ◽  
2021 ◽  
Vol 15 (1) ◽  
pp. 199
Author(s):  
Chengwei Lei ◽  
Weisong Tian
Keyword(s):  
Power Systems ◽  
Power Distribution ◽  
Distribution System ◽  
Distribution Systems ◽  
Short Circuit ◽  
Current Data ◽  
System Level ◽  
Power Distribution Systems ◽  
Power Distribution System ◽  
Protective Devices

Fused contactors and thermal magnetic circuit breakers are commonly applied protective devices in power distribution systems to protect the circuits when short-circuit faults occur. A power distribution system may contain various makes and models of protective devices, as a result, customizable simulation models for protective devices are demanded to effectively conduct system-level reliable analyses. To build the models, thermal energy-based data analysis methodologies are first applied to the protective devices’ physical properties, based on the manufacturer’s time/current data sheet. The models are further enhanced by integrating probability tools to simulate uncertainties in real-world application facts, for example, fortuity, variance, and failure rate. The customizable models are expected to aid the system-level reliability analysis, especially for the microgrid power systems.

scholarly journals Robust Stability Control for Electric Vehicles Connected to DC Distribution Systems

2021 ◽  
Vol 9 ◽  
Author(s):  
Wei Teng ◽  
Yuejiao Wang ◽  
Shumin Sun ◽  
Yan Cheng ◽  
Peng Yu ◽  
...  
Keyword(s):  
Electric Vehicles ◽  
Power Distribution ◽  
Distribution System ◽  
Distribution Systems ◽  
Voltage Stability ◽  
Stability Control ◽  
Power Distribution Systems ◽  
Power Distribution System ◽  
Dc Power ◽  
Dc Distribution

DC power distribution systems will play an important role in the future urban power distribution system, while the charging and discharging requirements of electric vehicles have a great impact on the voltage stability of the DC power distribution systems. A robust control method based on H∞ loop shaping method is proposed to suppress the effect of uncertain integration on voltage stability of DC distribution system. The results of frequency domain analysis and time domain simulation show that the proposed robust controller can effectively suppress the DC bus voltage oscillation caused by the uncertain integration of electric vehicle, and the robustness is strong.

scholarly journals Multilevel diode clamped D-Statcom for power quality improvement in distribution systems

2021 ◽  
Vol 12 (1) ◽  
pp. 217
Author(s):  
Jasti Venkata Ramesh Babu ◽  
Malligunta Kiran Kumar
Keyword(s):  
Power Quality ◽  
Power Distribution ◽  
Distribution System ◽  
Distribution Systems ◽  
Electrical Power ◽  
Reference Signal ◽  
Power Distribution System ◽  
Received Power ◽  
Multi Level ◽  
Result Analysis

Power quality is one big issue in power system and a big challenge for power engineers today. Electrical consumers (or otherwise load devices) expect electrical power received power should be of first-class. Bad quality in electrical power directs to fuse blowing, machine overheating, increase in distribution losses, damage to sensitive load devices and many more. DSTATCOM is one of the FACTS controllers designed to improve the quality in electrical power and thus improving the performance of distribution system. This paper presents a multilevel DSTATCOM topology to enhance power quality in power distribution system delivering high-quality power to the customer load devices. Diode-clamped structure is employed for multi-level DSTATCOM structure. ‘PQ’ based control strategy generates reference signal which is further processed through level-shifted multi-carrier PWM strategy for the generation of gate pulses to multi-level DSTATCOM structure. Simulation work of proposed system is developed and the result analysis is presented using MATLAB/SIMULINK software. Performance of multi-level DSTATCOM topology is verified with fixed and variable loads.

scholarly journals A Unified Theory of Neutral Grounding Methods in Power Distribution Systems

2020 ◽  
Author(s):  
Yubo Wang
Keyword(s):  
Power Distribution ◽  
Distribution System ◽  
Distribution Systems ◽  
Detection Sensitivity ◽  
Unified Theory ◽  
Power Distribution Systems ◽  
Power Distribution System ◽  
Earth Fault ◽  
History Of ◽  
Distribution Field

The neutral grounding in power distribution system is an important aspect for earth fault protection, power supply reliability and safety. The performance varies greatly with different grounding methods by which the protective effect presents various results with identical impedance of single phase earth fault. Arguments for better neutral protection has been continued in the distribution field for decades, unfortunately, there is still not a conclusion due to the discussions lacking of a unified modelling or theory of neutral groundings. Thus, the understanding of neutral grounding in most countries differs considerably. Surprisingly solid/isolated grounding in some countries is still considered as a mainstream grounding method in today’s distribution grids, likewise, some utilities are still persisting on adopting resistance grounding to pursue to improve detection sensitivity and reliability, and so on. In this paper, a unified theory is proposed to shed light on the neutral groundings within one unprecedented modelling by which neutral groundings can be compared and evaluated quantitatively for the first time in the history of power distribution field perhaps.

Sign in / Sign up

Export Citation Format

Share Document