Novel Combined Power and Cooling Thermodynamic Cycle for Low Temperature Heat Sources, Part II: Experimental Investigation

2003 ◽  
Vol 125 (2) ◽  
pp. 223-229 ◽  
Author(s):  
Gunnar Tamm ◽  
D. Yogi Goswami
Keyword(s):  
Low Temperature ◽  
System Analysis ◽  
Waste Heat ◽  
Thermal Power ◽  
Experimental System ◽  
Thermodynamic Cycle ◽  
Operating Conditions ◽  
Working Fluid ◽  
Water Mixture ◽  
Theoretical Simulation

A combined thermal power and cooling cycle proposed by Goswami is under intensive investigation, both theoretically and experimentally. The proposed cycle combines the Rankine and absorption refrigeration cycles, producing refrigeration while power is the primary goal. A binary ammonia-water mixture is used as the working fluid. This cycle can be used as a bottoming cycle using waste heat from a conventional power cycle or as an independent cycle using low temperature sources such as geothermal and solar energy. An experimental system was constructed to demonstrate the feasibility of the cycle and to compare the experimental results with the theoretical simulation. Results showed that the vapor generation and absorption condensation processes work experimentally, exhibiting expected trends, but with deviations from ideal and equilibrium modeling. The potential for combined turbine work and refrigeration output was evidenced in operating the system. Analysis of losses showed where improvements could be made, in preparation for further testing over a broader range of operating conditions.

A Novel Combined Power and Cooling Thermodynamic Cycle for Low Temperature Heat Sources: Part II — Experimental Investigation

Solar Energy ◽  
2002 ◽  
Author(s):  
Gunmar Tamm ◽  
D. Yogi Goswami
Keyword(s):  
Low Temperature ◽  
System Analysis ◽  
Waste Heat ◽  
Thermal Power ◽  
Experimental System ◽  
Thermodynamic Cycle ◽  
Working Fluid ◽  
Water Mixture ◽  
Theoretical Simulation ◽  
Intensive Investigation

A combined thermal power and cooling cycle proposed by Goswami is under intensive investigation, both theoretically and experimentally. The proposed cycle combines the Rankine and absorption refrigeration cycles, producing refrigeration while power is the primary goal. A binary ammonia-water mixture is used as the working fluid. This cycle can be used as a bottoming cycle using waste heat from a conventional power cycle or an independent cycle using low temperature sources such as geothermal and solar energy. An experimental system was constructed to demonstrate the feasibility of the cycle and to compare the experimental results with the theoretical simulation. Results showed that the vapor generation and absorption condensation processes work experimentally, exhibiting expected trends, but with deviations from ideal and equilibrium modeling. The potential for combined turbine work and refrigeration output was evidenced in operating the system. Analysis of losses showed where improvements could be made, in preparation for further testing over a broader range of operating parameters.

A Novel Combined Power and Cooling Thermodynamic Cycle for Low Temperature Heat Sources: Part I — Theoretical Investigation

Solar Energy ◽  
2002 ◽  
Author(s):  
Gunmar Tamm ◽  
D. Yogi Goswami ◽  
Shaoguang Lu ◽  
Afif A. Hasan
Keyword(s):  
Low Temperature ◽  
Heat Source ◽  
Waste Heat ◽  
Thermal Power ◽  
Thermodynamic Cycle ◽  
Working Fluid ◽  
Second Law ◽  
Water Mixture ◽  
Reduced Gradient Method ◽  
Generalized Reduced Gradient

A combined thermal power and cooling cycle proposed by Goswami is under intensive investigation, both theoretically and experimentally. The proposed cycle combines the Rankine and absorption refrigeration cycles, producing refrigeration while power is the primary goal. A binary ammonia-water mixture is used as the working fluid. This cycle can be used as a bottoming cycle using waste heat from a conventional power cycle or an independent cycle using low temperature sources such as geothermal and solar energy. Initial parametric studies of the cycle showed the potential for the cycle to be optimized for first or second law efficiency, as well as work or cooling output. For a solar heat source, optimization of the second law efficiency is most appropriate, since the spent heat source fluid is recycled through the solar collectors. The optimization results verified that the cycle could be optimized using the Generalized Reduced Gradient method. Theoretical results were extended to include realistic irreversibilities in the cycle, in preparation for the experimental study.

Novel Combined Power and Cooling Thermodynamic Cycle for Low Temperature Heat Sources, Part I: Theoretical Investigation

2003 ◽  
Vol 125 (2) ◽  
pp. 218-222 ◽  
Author(s):  
Gunnar Tamm ◽  
D. Yogi Goswami ◽  
Shaoguang Lu ◽  
Afif A. Hasan
Keyword(s):  
Low Temperature ◽  
Heat Source ◽  
Waste Heat ◽  
Thermal Power ◽  
Thermodynamic Cycle ◽  
Working Fluid ◽  
Second Law ◽  
Water Mixture ◽  
Parametric Studies ◽  
Intensive Investigation

A combined thermal power and cooling cycle proposed by Goswami is under intensive investigation, both theoretically and experimentally. The proposed cycle combines the Rankine and absorption refrigeration cycles, producing refrigeration while power is the primary goal. A binary ammonia-water mixture is used as the working fluid. This cycle can be used as a bottoming cycle using waste heat from a conventional power cycle or as an independent cycle using low temperature sources such as geothermal and solar energy. Initial parametric studies of the cycle showed the potential for the cycle to be optimized for first or second law efficiency, as well as work or cooling output. For a solar heat source, optimization of the second law efficiency is most appropriate, since the spent heat source fluid is recycled through the solar collectors. The optimization results verified that the cycle could be optimized. Theoretical results were extended to include realistic irreversibilities in the cycle, in preparation for the experimental study.

A New Combined Power and Cooling Cycle for Low Temperature Heat Sources

2003 ◽  
Author(s):  
D. Y. Goswami ◽  
Gunnar Tamm ◽  
Sanjay Vijayaraghavan
Keyword(s):  
Low Temperature ◽  
Heat Source ◽  
Waste Heat ◽  
Experimental System ◽  
Operating Conditions ◽  
Working Fluid ◽  
Second Law ◽  
Heat Sources ◽  
Vapor Generation ◽  
Temperature Heat

A new thermodynamic cycle has been developed for the simultaneous production of power and cooling from low temperature heat sources. The proposed cycle combines the Rankine and absorption refrigeration cycles, providing power and cooling in desired ratios to best suit the application. A binary mixture of ammonia and water is used as the working fluid, providing a good thermal match with the sensible heat source over a range of boiling temperatures. Due to its low boiling point, the ammonia-rich vapor expands to refrigeration temperatures while work is extracted through the turbine. Absorption condensation of the vapor back into the bulk solution occurs near ambient temperatures. The proposed cycle is suitable as a bottoming cycle using waste heat from conventional power generation systems, or can utilize low temperature solar or geothermal renewable resources. The cycle can be scaled to residential, commercial or industrial uses, providing power as the primary goal while satisfying some of the cooling requirements of the application. The cycle is under both theoretical and experimental investigations. Initial parametric studies of how the cycle performs at various operating conditions showed the potential for the cycle to be optimized. Optimization studies performed over a range of heat source and heat sink temperatures showed that the cycle could be optimized for maximum work or cooling output, or for first or second law efficiencies. Depending on the heat source temperatures, as much as half of the output may be obtained as refrigeration under optimized conditions, with refrigeration temperatures as low as 205 K being achievable. Maximum second law efficiencies over 60% have been found with the heat source between 350 and 450 K. An experimental system was constructed to verify the theoretical results and to demonstrate the feasibility of the cycle. The investigation focused on the vapor generation and absorption processes, setting up for the power and refrigeration studies to come later. The turbine was simulated with an equivalent expansion process in this initial phase of testing. Results showed that the vapor generation and absorption processes work experimentally, over a range of operating conditions and in simulating the sources and sinks of interest. The potential for combined work and cooling output was evidenced in operating the system. Comparison to ideally simulated results verified that there are thermal and flow losses present, which were assessed to make both improvements in the experimental system and modifications in the simulations to include realistic losses.

Parametric Study of a Combined Power and Cooling Thermodynamic Cycle for Low Temperature Heat Sources

2009 ◽  
Author(s):  
Ricardo Vasquez Padilla ◽  
Gokmen Demirkaya ◽  
D. Yogi Goswami ◽  
Elias L. Stefanakos
Keyword(s):  
Low Temperature ◽  
Parametric Study ◽  
Waste Heat ◽  
Ammonia Concentration ◽  
Combined Cycle ◽  
Operating Conditions ◽  
Optimum Operating ◽  
Working Fluid ◽  
Basic Solution ◽  
Water Mixture

A combined power/cooling cycle, which combines the Rankine and absorption refrigeration cycles, uses ammonia-water mixture as a working fluid and produces power and refrigeration while power is the primary goal. This cycle, also known as the Goswami Cycle, can be used as a bottoming cycle using waste heat from a conventional power cycle or as an independent cycle using low temperature sources such as geothermal and solar energy. This paper presents a parametric analysis of the combined cycle. Parametric study of the cycle was carried out in the commercial software Chemcad 6.1. The thermodynamic property data used in simulations were validated with experimental data. Chemcad model was also compared with simulations previously carried out in the process simulator Aspen Plus. The agreement between the two sets has proved the accuracy of the model developed in Chemcad. Then, optimum operating conditions were found for a range of ammonia concentration in the basic solution, isentropic expander efficiency and boiler pressure. It is shown that the cycle can be optimized for net work, cooling output, effective first and exergy efficiencies.

scholarly journals Comparison of the Trilateral Flash Cycle and Rankine Cycle with Organic Fluid Using the Pinch Point Temperature

Entropy ◽  
2019 ◽  
Vol 21 (12) ◽  
pp. 1197
Author(s):  
Kai-Yuan Lai ◽  
Yu-Tang Lee ◽  
Miao-Ru Chen ◽  
Yao-Hsien Liu
Keyword(s):  
Low Temperature ◽  
Heat Recovery ◽  
Waste Heat Recovery ◽  
Waste Heat ◽  
Rankine Cycle ◽  
Operating Conditions ◽  
Heat Extraction ◽  
Working Fluid ◽  
Pinch Point ◽  
Temperature Heat

Low-temperature heat utilization can be applied to waste heat from industrial processes or renewable energy sources such as geothermal and ocean energy. The most common low-temperature waste-heat recovery technology is the organic Rankine cycle (ORC). However, the phase change of ORC working fluid for the heat extraction process causes a pinch-point problem, and the heat recovery cannot be efficiently used. To improve heat extraction and power generation, this study explored the cycle characteristics of the trilateral flash cycle (TFC) in a low-temperature heat source. A pinch-point-based methodology was developed for studying the optimal design point and operating conditions and for optimizing working fluid evaporation temperature and mass flow rate. According to the simulation results, the TFC system can recover more waste heat than ORC under the same operating conditions. The net power output of the TFC was approximately 30% higher than ORC but at a cost of higher pump power consumption. Additionally, the TFC was superior to ORC with an extremely low-temperature heat source (<80 °C), and the ideal efficiency was approximately 3% at the highest work output condition. The TFC system is economically beneficial for waste-heat recovery for low-temperature heat sources.

scholarly journals Component-Oriented Modeling of a Micro-Scale Organic Rankine Cycle System for Waste Heat Recovery Applications

2021 ◽  
Vol 11 (5) ◽  
pp. 1984
Author(s):  
Ramin Moradi ◽  
Emanuele Habib ◽  
Enrico Bocci ◽  
Luca Cioccolanti
Keyword(s):  
Electric Power ◽  
Heat Recovery ◽  
Waste Heat Recovery ◽  
Waste Heat ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Operating Conditions ◽  
Working Fluid ◽  
Pump Efficiency ◽  
Micro Scale

Organic Rankine cycle (ORC) systems are some of the most suitable technologies to produce electricity from low-temperature waste heat. In this study, a non-regenerative, micro-scale ORC system was tested in off-design conditions using R134a as the working fluid. The experimental data were then used to tune the semi-empirical models of the main components of the system. Eventually, the models were used in a component-oriented system solver to map the system electric performance at varying operating conditions. The analysis highlighted the non-negligible impact of the plunger pump on the system performance Indeed, the experimental results showed that the low pump efficiency in the investigated operating range can lead to negative net electric power in some working conditions. For most data points, the expander and the pump isentropic efficiencies are found in the approximate ranges of 35% to 55% and 17% to 34%, respectively. Furthermore, the maximum net electric power was about 200 W with a net electric efficiency of about 1.2%, thus also stressing the importance of a proper selection of the pump for waste heat recovery applications.

A Parametric Examination of the Factors Affecting the Performance of a Diffusion Absorption Refrigeration System

2021 ◽  
pp. 1-38
Author(s):  
Noman Yousuf ◽  
Timothy Anderson ◽  
Roy Nates
Keyword(s):  
Waste Heat ◽  
Operating Conditions ◽  
Design Parameters ◽  
Working Fluid ◽  
Low Grade ◽  
Absorption Refrigeration ◽  
Factors Affecting ◽  
Thermally Driven ◽  
Mass Flowrate ◽  
Diffusion Absorption

Abstract Despite being identified nearly a century ago, the diffusion absorption refrigeration (DAR) cycle has received relatively little attention. One of the strongest attractions of the DAR cycle lies in the fact that it is thermally driven and does not require high value work. This makes it a prime candidate for harnessing low grade heat from solar collectors, or the waste heat from stationary generators, to produce cooling. However, to realize the benefits of the DAR cycle, there is a need to develop an improved understanding of how design parameters influence its performance. In this vein, this work developed a new parametric model that can be used to examine the performance of the DAR cycle for a range of operating conditions. The results showed that the cycle's performance was particularly sensitive to several factors: the rate of heat added and the temperature of the generator, the effectiveness of the gas and solution heat exchangers, the mass flowrate of the refrigerant and the type of the working fluid. It was shown that can deliver good performance at low generator temperatures if the refrigerant mass fraction in the strong solution is made as high as possible. Moreover, it was shown that a H2O-LiBr working pair could be useful for achieving cooling at low generator temperatures.

Optimization of a Novel Combined Power/Refrigeration Thermodynamic Cycle

Solar Energy ◽  
2002 ◽  
Author(s):  
Shaoguang Lu ◽  
D. Yogi Goswami
Keyword(s):  
Waste Heat ◽  
Thermodynamic Cycle ◽  
Cycle Performance ◽  
Working Fluid ◽  
Second Law ◽  
Optimum Conditions ◽  
Ambient Temperatures ◽  
Reduced Gradient ◽  
Generalized Reduced Gradient ◽  
Performance Conditions

A novel combined power/refrigeration thermodynamic cycle is optimized for thermal performance in this paper. The cycle uses ammonia-water binary mixture as a working fluid and can be driven by various heat sources, such as solar, geothermal and low temperature waste heat. It could produce power as well as refrigeration with power output as a primary goal. The optimization program, which is based on the Generalized Reduced Gradient (GRG) algorithm, can be used to optimize for different objective functions. Examples that maximize second law efficiency, work output and refrigeration output are presented, showing the cycle may be optimized for any desired performance parameter. In addition, cycle performance over a range of ambient temperatures was investigated. It was found that for a source temperature of 360K, which is in the range of flat plate solar collectors, both power and refrigeration outputs are achieved under optimum conditions. All performance parameters, including first and second law efficiencies, power and refrigeration output decrease as the ambient temperature goes up. On the other hand, for a source of 440K, optimum conditions do not provide any refrigeration. However, refrigeration can be obtained even for this temperature under non-optimum performance conditions.

Waste Heat Recovery in a Cruise Vessel in the Baltic Sea by Using an Organic Rankine Cycle: A Case Study

2015 ◽  
Author(s):  
Fredrik Ahlgren ◽  
Maria E. Mondejar ◽  
Magnus Genrup ◽  
Marcus Thern
Keyword(s):  
Power Output ◽  
Heat Recovery ◽  
Waste Heat Recovery ◽  
Waste Heat ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Operating Conditions ◽  
Maritime Transportation ◽  
Working Fluid ◽  
Net Power Output

Maritime transportation is a significant contributor to SOx, NOx and particle matter emissions, even though it has a quite low CO2 impact. New regulations are being enforced in special areas that limit the amount of emissions from the ships. This fact, together with the high fuel prices, is driving the marine industry towards the improvement of the energy efficiency of current ship engines and the reduction of their energy demand. Although more sophisticated and complex engine designs can improve significantly the efficiency of the energy systems in ships, waste heat recovery arises as the most influent technique for the reduction of the energy consumption. In this sense, it is estimated that around 50% of the total energy from the fuel consumed in a ship is wasted and rejected in fluid and exhaust gas streams. The primary heat sources for waste heat recovery are the engine exhaust and the engine coolant. In this work, we present a study on the integration of an organic Rankine cycle (ORC) in an existing ship, for the recovery of the main and auxiliary engines exhaust heat. Experimental data from the operating conditions of the engines on the M/S Birka Stockholm cruise ship were logged during a port-to-port cruise from Stockholm to Mariehamn over a period of time close to one month. The ship has four main engines Wärtsilä 5850 kW for propulsion, and four auxiliary engines 2760 kW used for electrical consumers. A number of six load conditions were identified depending on the vessel speed. The speed range from 12–14 knots was considered as the design condition, as it was present during more than 34% of the time. In this study, the average values of the engines exhaust temperatures and mass flow rates, for each load case, were used as inputs for a model of an ORC. The main parameters of the ORC, including working fluid and turbine configuration, were optimized based on the criteria of maximum net power output and compactness of the installation components. Results from the study showed that an ORC with internal regeneration using benzene would yield the greatest average net power output over the operating time. For this situation, the power production of the ORC would represent about 22% of the total electricity consumption on board. These data confirmed the ORC as a feasible and promising technology for the reduction of fuel consumption and CO2 emissions of existing ships.

Sign in / Sign up

Export Citation Format

Share Document