Self-Folding and Unfolding of Carbon Nanotubes

2005 ◽  
Vol 128 (1) ◽  
pp. 3-10 ◽  
Author(s):  
Markus J. Buehler ◽  
Yong Kong ◽  
Huajian Gao ◽  
Yonggang Huang

Carbon nanotubes (CNTs) constitute a prominent example of nanomaterials. In most studies on mechanical properties, the effort was concentrated on CNTs with relatively small aspect ratio of length to diameters. In contrast, CNTs with aspect ratios of several hundred can be produced with today’s experimental techniques. We report atomistic-continuum studies of single-wall carbon nanotubes with very large aspect ratios subject to compressive loading. It was recently shown that these long tubes display significantly different mechanical behavior than tubes with smaller aspect ratios (Buehler, M. J., Kong, Y., and Guo, H., 2004, ASME J. Eng. Mater. Technol. 126, pp. 245–249). We distinguish three different classes of mechanical response to compressive loading. While the deformation mechanism is characterized by buckling of thin shells in nanotubes with small aspect ratios, it is replaced by a rodlike buckling mode above a critical aspect ratio, analogous to the Euler theory in continuum mechanics. For very large aspect ratios, a nanotube is found to behave like a wire that can be deformed in a very flexible manner to various shapes. In this paper, we focus on the properties of such wirelike CNTs. Using atomistic simulations carried out over a several-nanoseconds time span, we observe that wirelike CNTs behave similarly to flexible macromolecules. Our modeling reveals that they can form thermodynamically stable self-folded structures, where different parts of the CNTs attract each other through weak van der Waals (vdW) forces. This self-folded CNT represents a novel structure not described in the literature. There exists a critical length for self-folding of CNTs that depends on the elastic properties of the tube. We observe that CNTs fold below a critical temperature and unfold above another critical temperature. Surprisingly, we observe that self-folded CNTs with very large aspect ratios never unfold until they evaporate. The folding-unfolding transition can be explained by entropic driving forces that dominate over the elastic energy at elevated temperature. These mechanisms are reminiscent of the dynamics of biomolecules, such as proteins. The different stable states of CNTs are finally summarized in a schematic phase diagram of CNTs.

2004 ◽  
Vol 126 (3) ◽  
pp. 245-249 ◽  
Author(s):  
Markus J. Buehler ◽  
Yong Kong ◽  
Huajian Gao

We report atomistic studies of single-wall carbon nanotubes with very large aspect ratios subject to compressive loading. These long tubes display significantly different mechanical behavior than tubes with smaller aspect ratios. We distinguish three different classes of mechanical response to compressive loading. While the deformation mechanism is characterized by buckling of thin shells in nanotubes with small aspect ratios, it is replaced by a rod-like buckling mode above a critical aspect ratio, analogous to the Euler theory in continuum mechanics. For very large aspect ratios, a nanotube is found to behave like a flexible macromolecule which tends to fold due to vdW interactions between different parts of the carbon nanotube. This suggests a shell-rod-wire transition of the mechanical behavior of carbon nanotubes with increasing aspect ratios. While continuum mechanics concepts can be used to describe the first two types of deformation, statistical methods will be necessary to describe the dynamics of wire-like long tubes.


Author(s):  
Arka P. Chattopadhyay ◽  
Elizabeth Frink ◽  
Kevin Lease ◽  
X. J. Xin

Buckling of plates and tubes plays an important role in structural safety and energy absorption. Although buckling of plates and tubes has been studied theoretically and experimentally in the past, the effects of aspect ratio and side constraint on buckling of multi-wall structures and tubes has not been investigated systematically. In this work, finite element simulations have been carried out to investigate the buckling behavior of multi-wall structures and tubes. A series of one- to three-panel walls and square tubes with various aspect ratios were simulated. The critical aspect ratios causing buckling mode transition were obtained and compared with theoretical predictions available in the literature. Effects of wall angle and side constraint on buckling behavior were investigated. The relevance of research findings to honeycomb-like structures was discussed.


2003 ◽  
Vol 785 ◽  
Author(s):  
S. Gupta ◽  
M. Hughes ◽  
A.H. Windle ◽  
J. Robertson

ABSTRACTCarbon nanotubes-based actuator has been investigated using in situ Raman spectroscopy in order to understand the actuation mechanism and to determine associated parameters. We built an actuator from a sheet of single-wall carbon nanotubes (SWNT mat) and studied in several alkali metal (Li, Na, and K) and alkaline earth (Ca) halide solutions. Since Raman can detect changes in C-C bond length: the radial breathing mode (RBM) at ∼190 cm-1 varies inversely with the nanotube diameter and the G band at ∼1590 cm-1 varies with the axial bond length, the variation of bonding was monitored with potential. In addition, the intensities of both the modes vary with either emptying/depleting or filling of the bonding and antibonding states due to electrochemical charge injection. We discuss the variation of intensity/frequency providing valuable information on the dynamics of charge transfer on the SWNT mat surface. We found the in-plane microscopic strain (∼ -0.25%) and the charge transfer per carbon atom (fc ∼ -0.005) as an upper bound for the electrolytes used. It is demonstrated that though the present analyses does comply with the proposition made earlier, but the quantitative estimates of the associated parameters are significantly lower if compared with those of reported values for carbon nanotubes. Moreover, the extent of variation (i.e. coupled electro-chemo-mechanical response) does depend upon the type of counter-ion used. The cyclic voltammetry (CV) is also described briefly.


Author(s):  
R. P. Raffaelle ◽  
B. Landi ◽  
T. Gennett ◽  
R. S. Morris ◽  
B. Dixon ◽  
...  

Novel carbon materials with nanometer dimensions are of potentially significant importance for a number of advanced technological applications. Currently, considerable interest exists in the possible applications of single wall carbon nanotubes (SWNTs) to proton exchange membrane (PEM) fuel cells. Proposed uses include as anode materials in both hydrogen and direct methanol fuel cells, solid polymer electrolyte additives, active cathode materials and bipolar plate interconnects. One of the desirable attributes afforded by the use of SWNTs in fuel cell applications stems from a combination of their extremely high electrical conductivity and large aspect ratios which results in a low weight percent for the electrical percolation threshold. This conductivity combined with the outstanding catalytic surface area offered by these nanostructured materials makes them a potentially outstanding active material for PEM electrodes. In addition, the high thermal conductivity, enhanced mechanical properties and corrosion resistance of polymer-SWNT composites may play a large role in developing new fuel cell designs such as thin-film microelectronic fuel cells. We will review the current applications involving SWNTs in PEM fuel cells and report on the recent work in the Nanopower Research Lab at RIT and it partners on utilizing high purity SWNT’s in microelectronic fuel cells.


Nanoscale ◽  
2015 ◽  
Vol 7 (15) ◽  
pp. 6745-6753 ◽  
Author(s):  
Taeheon Lee ◽  
Byunghee Kim ◽  
Sumin Kim ◽  
Jong Hun Han ◽  
Heung Bae Jeon ◽  
...  

We synthesized p(FMA-co-DMAEMA) for the dispersion of SWCNTs while maintaining their high aspect ratios.


2007 ◽  
Vol 1049 ◽  
Author(s):  
A. A. Zbib ◽  
S. Dj. Mesarovic ◽  
D. F. Bahr ◽  
E. T. Lilleodden ◽  
J. Jiao ◽  
...  

AbstractWhen grown via chemical vapor deposition carbon nanotubes (CNTs) may take on the form of a “turf”, consisting of many CNTs with a complex interconnectedness attached to an inflexible substrate. These turfs can be formed over large areas and with a range of heights (between 1 to 100 μm), and grown on photolithographically patterned catalysts to form different aspect ratios. This study focuses on the indentation and permanent deformation of CNT assemblages under applied contact loading. Nanoindentation was conducted on CNT turfs and the properties, nominally the turf's elastic modulus and hardness, were 14.9 MPa ± 5.7 MPa and 2 MPa respectively. The onset of permanent deformation during indentation occurred at applied stresses of 2.5 MPa. The turf's collective permanent deformation under applied compressive loading was also studied. A model predicting the buckling stress of CNT turfs is also described.


2009 ◽  
Vol 1210 ◽  
Author(s):  
Zhongrui Li ◽  
Viney Saini ◽  
Shawn Edward Bourdo ◽  
Liqiu Zheng ◽  
Enkeleda Dervishi ◽  
...  

AbstractSingle-wall carbon nanotubes (SWNTs) are potentially an attractive material for PV applications due to their many unique structural and electrical properties. SWNTs can be directly configured as energy conversion materials to fabricate thin-film solar cells, with nanotubes serving as both photogeneration sites and charge carriers collecting/transport layers. SWNTs can be modified into either p-type conductor through chemical doping (like thionyl chloride, or just exposure to air) or n-type conductor through polymer (like polyethylene imine) functionalization. The solar cells consist of either a semitransparent thin film of p-type nanotubes deposited on an n-type silicon wafer or a semitransparent thin film of n-type SWNT on p-type substrate to create high-density p-n heterojunctions between nanotubes and silicon substrate to favor charge separation and extract electrons and holes. The high aspect ratios and large surface area of nanotubes can be beneficial to exciton dissociation and charge carrier transport thus improving the power conversion efficiency.


2009 ◽  
Vol 131 (8) ◽  
Author(s):  
Choon-Sik Jhun ◽  
Michael C. Evans ◽  
Victor H. Barocas ◽  
Robert T. Tranquillo

Though it is widely accepted that fiber alignment has a great influence on the mechanical anisotropy of tissues, a systematic study of the influence of fiber alignment on the macroscopic mechanical behavior by native tissues is precluded due to their predefined microstructure and heterogeneity. Such a study is possible using collagen-based bioartificial tissues that allow for alignment to be prescribed during their fabrication. To generate a systemic variation of strength of fiber alignment, we made cruciform tissue constructs in Teflon molds that had arms of different aspect ratios. We implemented our anisotropic biphasic theory of tissue-equivalent mechanics to simulate the compaction by finite element analysis. Prior to tensile testing, the construct geometry was standardized by cutting test samples with a 1:1 cruciform punch after releasing constructs from the molds. Planar biaxial testing was performed on these samples, after stretching them to their in-mold dimensions to recover in-mold alignment, to observe the macroscopic mechanical response with simultaneous fiber alignment imaging using a polarimetry system. We found that the strength of fiber alignment of the samples prior to release from the molds linearly increased with anisotropy of the mold. In testing after release, modulus ratio (modulus in fiber direction/modulus in normal direction) was greater as the initial strength of fiber alignment increased, that is, as the aspect ratio increased. We also found that the fiber alignment strength and modulus ratio increased in a hyperbolic fashion with stretching for a sample of given aspect ratio.


2013 ◽  
Vol 1505 ◽  
Author(s):  
Danhao Ma ◽  
Ruwantha Jayasingha ◽  
Dustin Hess ◽  
Kofi W. Adu ◽  
Gamini U. Sumanasekera

AbstractWe report an increase in superconducting temperature of magnesium diboride (MgB2) by minute single-wall carbon nanotubes (SWCNT) inclusions. The SWCNTs concentration was varied from 0.1wt% to 1.0wt%. The temperature dependence resistivity of sintered MgB2- SWCNTs composites containing 0.1wt%, 0.5wt% and 1.0wt% were measured and compared with that of the pure MgB2. The superconducting critical temperature (Tc) of the MgB2 increased from 40 K to as high as 42.4 K for the MgB2 containing 0.5wt% of SWCNTs. The room temperature resistivity ratio (RRR) shows dependence on the sample composition. The temperature width (ΔT) decreases with increasing SWCNT content from 0.1wt% to 1.0wt%. The normal state resistivity data were fitted with the generalized Block-Grüneisen function obtaining a Debye temperature of ∼ 900K.


2009 ◽  
Vol 66 ◽  
pp. 198-201
Author(s):  
Shirley Zhiqi Shen ◽  
Stuart Bateman ◽  
Chi Huynh ◽  
Mel Dell'Olio ◽  
Stephen Hawkins ◽  
...  

This paper compared the effect of aspect ratios and dispersions of carbon nanotubes (CNT) made in CSIRO, with a broad range of aspect ratios with similar dimensions in diameter, on the electric conductivity, rheology and dynamic mechanical thermal analysis of multi-wall nanotubes (MWNT)/epoxy nanocomposites. A medium aspect ratio seems to be the most effective in conductive network formation in epoxy matrix and also provide best storage modulus of CNT/epoxy nanocomposites under providing processing conditions.


Sign in / Sign up

Export Citation Format

Share Document