PIV Study of Shallow Open Channel Flow Over d- and k-Type Transverse Ribs

2007 ◽  
Vol 129 (8) ◽  
pp. 1058-1072 ◽  
Author(s):  
M. F. Tachie ◽  
K. K. Adane
Keyword(s):  
Boundary Layer ◽  
Friction Coefficient ◽  
Skin Friction ◽  
Cross Section ◽  
Open Channel ◽  
Skin Friction Coefficient ◽  
Mixing Length ◽  
Mean Flow ◽  
Turbulent Statistics ◽  
The Mean

A particle image velocimetry was used to study shallow open channel turbulent flow over d-type and k-type transverse ribs of square, circular, and semi-circular cross sections. The ratio of boundary layer thickness to depth of flow varied from 50% to 90%. The mean velocities and turbulent quantities were evaluated at the top plane of the ribs to characterize interaction between the cavities and overlying boundary layer. It was found that the overlying boundary layer interacts more strongly with k-type cavities than observed for d-type cavities. The profiles of the mean velocities and turbulent statistics were then spatially averaged over a pitch, and these profiles were used to study the effects of rib type and cross section on the flow field. The mean velocity gradients were found to be non-negligible across the boundary layer, and the implications of this observation for momentum transport, eddy viscosity, and mixing length distributions are discussed. The results show that the skin friction coefficient, Reynolds stresses and mixing length distributions are independent of rib cross section for d-type. For the k-type ribs, significant variations in skin friction coefficient values, mean flow, and turbulence fields are observed between square ribs and circular/semi-circular ribs.

Air Blowing Into Boundary Layer Of A Flat Plate With Length-Dependent Permeability

2016 ◽  
Vol 11 (3) ◽  
pp. 16-26
Author(s):  
Vladimir Kornilov ◽  
Andrey Boiko ◽  
Ivan Kavun ◽  
Anatoliy Popkov
Keyword(s):  
Boundary Layer ◽  
Friction Coefficient ◽  
Flat Plate ◽  
Skin Friction ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Skin Friction Coefficient ◽  
Air Blowing ◽  
The Mean

A generalized analysis of the results of numerical and experimental studies of air blowing into a turbulent boundary layer through finely perforated surface consisting of alternating permeable and impermeable sections of varying length providing a sudden change in the flow conditions at the boundaries of these sections is presented. The air blowing coefficient Cb determined by the mass flow rate per unit area of the active perforated sample varied in the range from 0 to 0.008. It is shown that as Cb grows, the maximum reduction in the mean surface skin-friction coefficient CF, which is the value through the permeable area of perforated sample, reaches about 65 %. When keeping the equal mass flow rate Q for all tested combinations, the mean skin-friction coefficient remains constant, independent of geometrical parameters of permeable and impermeable sections. Increasing the length of the last permeable section leads to the growth of relaxation region which is characterized by the reduced skin friction values on the impermeable part of the flat plate.

Experimental Investigation of Turbulent Boundary Layers Under Favorable Pressure Gradient

2010 ◽  
Author(s):  
Pranav Joshi ◽  
Joseph Katz
Keyword(s):  
Boundary Layer ◽  
Friction Coefficient ◽  
Pressure Gradient ◽  
Skin Friction ◽  
Velocity Profiles ◽  
Skin Friction Coefficient ◽  
Mean Velocity ◽  
Freestream Velocity ◽  
Favorable Pressure Gradient ◽  
The Mean

The goal of this research is to study the effect of favorable pressure gradient (FPG) on the near wall structures of a turbulent boundary layer on a smooth wall. 2D-PIV measurements have been performed in a sink flow, initially at a coarse resolution, to characterize the development of the mean flow and (under resolved) Reynolds stresses. Lack of self-similarity of mean velocity profiles shows that the boundary layer does not attain the sink flow equilibrium. In the initial phase of acceleration, the acceleration parameter, K = v/U2dU/dx, increases from zero to 0.575×10−6, skin friction coefficient decreases and mean velocity profiles show a log region, but lack universality. Further downstream, K remains constant, skin friction coefficient increases and the mean velocity profiles show a second log region away from the wall. In the initial part of the FPG region, all the Reynolds stress components decrease over the entire boundary layer. In the latter phase, they continue to decrease in the middle of the boundary layer, and increase significantly close to the wall (below y∼0.15δ), where they collapse when normalized with the local freestream velocity. Turbulence production and wallnormal transport, scaled with outer units, show self-similar profiles close to the wall in the constant K region. Spanwise-streamwise plane data shows evidence of low speed streaks in the log layer, with widths scaling with the boundary layer thickness.

The Effect of Biofilms on Turbulent Boundary Layers

1999 ◽  
Vol 121 (1) ◽  
pp. 44-51 ◽  
Author(s):  
M. P. Schultz ◽  
G. W. Swain
Keyword(s):  
Boundary Layer ◽  
Friction Coefficient ◽  
Turbulent Boundary Layer ◽  
Skin Friction ◽  
Layer Structure ◽  
Reynolds Shear Stress ◽  
Skin Friction Coefficient ◽  
Laser Doppler Velocimeter ◽  
Reynolds Stresses ◽  
The Mean

Materials exposed in the marine environment, including those protected by antifouling paints, may rapidly become colonized by microfouling. This may affect frictional resistance and turbulent boundary layer structure. This study compares the mean and turbulent boundary layer velocity characteristics of surfaces covered with a marine biofilm with those of a smooth surface. Measurements were made in a nominally zero pressure gradient, boundary layer flow with a two-component laser Doppler velocimeter at momentum thickness Reynolds numbers of 5600 to 19,000 in a recirculating water tunnel. Profiles of the mean and turbulence velocity components, including the Reynolds shear stress, were measured. An average increase in the skin friction coefficient of 33 to 187 percent was measured on the fouled specimens. The skin friction coefficient was found to be dependent on both biofilm thickness and morphology. The biofilms tested showed varying effect on the Reynolds stresses when those quantities were normalized with the friction velocity.

Large-eddy simulation of flow over a cylinder with from to : a skin-friction perspective

2017 ◽  
Vol 820 ◽  
pp. 121-158 ◽  
Author(s):  
W. Cheng ◽  
D. I. Pullin ◽  
R. Samtaney ◽  
W. Zhang ◽  
W. Gao
Keyword(s):  
Boundary Layer ◽  
Friction Coefficient ◽  
Large Eddy Simulation ◽  
Skin Friction ◽  
Flow Separation ◽  
Skin Friction Coefficient ◽  
Cylinder Surface ◽  
Mean Flow ◽  
Eddy Simulation ◽  
Large Eddy

We present wall-resolved large-eddy simulations (LES) of flow over a smooth-wall circular cylinder up to$Re_{D}=8.5\times 10^{5}$, where$Re_{D}$is Reynolds number based on the cylinder diameter$D$and the free-stream speed$U_{\infty }$. The stretched-vortex subgrid-scale (SGS) model is used in the entire simulation domain. For the sub-critical regime, six cases are implemented with$3.9\times 10^{3}\leqslant Re_{D}\leqslant 10^{5}$. Results are compared with experimental data for both the wall-pressure-coefficient distribution on the cylinder surface, which dominates the drag coefficient, and the skin-friction coefficient, which clearly correlates with the separation behaviour. In the super-critical regime, LES for three values of$Re_{D}$are carried out at different resolutions. The drag-crisis phenomenon is well captured. For lower resolution, numerical discretization fluctuations are sufficient to stimulate transition, while for higher resolution, an applied boundary-layer perturbation is found to be necessary to stimulate transition. Large-eddy simulation results at$Re_{D}=8.5\times 10^{5}$, with a mesh of$8192\times 1024\times 256$, agree well with the classic experimental measurements of Achenbach (J. Fluid Mech., vol. 34, 1968, pp. 625–639) especially for the skin-friction coefficient, where a spike is produced by the laminar–turbulent transition on the top of a prior separation bubble. We document the properties of the attached-flow boundary layer on the cylinder surface as these vary with$Re_{D}$. Within the separated portion of the flow, mean-flow separation–reattachment bubbles are observed at some values of$Re_{D}$, with separation characteristics that are consistent with experimental observations. Time sequences of instantaneous surface portraits of vector skin-friction trajectory fields indicate that the unsteady counterpart of a mean-flow separation–reattachment bubble corresponds to the formation of local flow-reattachment cells, visible as coherent bundles of diverging surface streamlines.

Low-Reynolds-Number Turbulent Boundary Layers in Zero and Favorable Pressure Gradients

1983 ◽  
Vol 27 (03) ◽  
pp. 147-157 ◽  
Author(s):  
A. J. Smits ◽  
N. Matheson ◽  
P. N. Joubert
Keyword(s):  
Friction Coefficient ◽  
Skin Friction ◽  
Boundary Layers ◽  
Leading Edge ◽  
Reynolds Numbers ◽  
Skin Friction Coefficient ◽  
Turbulent Boundary Layers ◽  
Pressure Gradients ◽  
Mean Flow ◽  
Low Reynolds

This paper reports the results of an extensive experimental investigation into the mean flow properties of turbulent boundary layers with momentum-thickness Reynolds numbers less than 3000. Zero pressure gradient and favorable pressure gradients were studied. The velocity profiles displayed a logarithmic region even at very low Reynolds numbers (as low as Rθ = 261). The results were independent of the leading-edge shape, and the pin-type turbulent stimulators performed well. It was found that the shape and Clauser parameters were a little higher than the correlation proposed by Coles [10], and the skin friction coefficient was a little lower. The skin friction coefficient behavior could be fitted well by a simple power-law relationship in both zero and favorable pressure gradients.

Control of Separated Boundary-Layer on Subsonic Airfoil Using Vortex Generator Jet Devices

2006 ◽  
Author(s):  
A. Kourta ◽  
G. Petit ◽  
J. C. Courty ◽  
J. P. Rosenblum
Keyword(s):  
Boundary Layer ◽  
Friction Coefficient ◽  
Skin Friction ◽  
Three Dimensional ◽  
Vortex Generator ◽  
Leading Edge ◽  
Skin Friction Coefficient ◽  
Synthetic Jets ◽  
High Lift ◽  
Longitudinal Vortices

The control of subsonic high lift induced separation on airfoil may improve the flight envelope of current aircraft or even simplify the complex and heavy high-lift devices on commercial airframes. Until now, synthetic jets have proved a really interesting efficiency to delay or remove even leading-edge located separated areas on high-lift configuration but are not efficient for real scale aircrafts. In case of pressure-like separation (i.e. from trailing-edge), synthetic jets can be replaced by so the called “Vortex Generator Jets” which create strong longitudinal vortices that increase mixing in inner boundary layer and consequently the skin friction coefficient is increased to prevent separation. In this study, numerical simulations were undertaken on a generic three dimensional flat plate in order to quantify the effect of the longitudinal vortices on the natural skin friction coefficient. Both counter and co-rotative devices were tested at different exhaust velocities and distances between each others. Finally co-rotative vortex generators jets were tested on a three dimensional generic airfoil ONERA D. Results show a delay of the separation occurence but this solution does not seem to be as robust as synthetic jets. The study of jets spacing with respect to the efficiency of the devices shows a maximum for a given ratio of spacing to exhaust velocity.

Image-based modelling of the skin-friction coefficient in compressible boundary-layer transition

2019 ◽  
Vol 875 ◽  
pp. 1175-1203 ◽  
Author(s):  
Wenjie Zheng ◽  
Shanxin Ruan ◽  
Yue Yang ◽  
Lin He ◽  
Shiyi Chen
Keyword(s):  
Boundary Layer ◽  
Friction Coefficient ◽  
Skin Friction ◽  
Inclination Angle ◽  
Large Scale ◽  
Skin Friction Coefficient ◽  
Boundary Layer Transition ◽  
Small Scale ◽  
Layer Transition ◽  
Scale Structures

We develop a model of the skin-friction coefficient based on scalar images in the compressible, spatially evolving boundary-layer transition. The images are extracted from a passive scalar field by a sliding window filter on the streamwise and wall-normal plane. The multi-scale and multi-directional geometric analysis is applied to characterize the averaged inclination angle of spatially evolving filtered component fields at different scales ranging from a boundary-layer thickness to several viscous length scales. In general, the averaged inclination angles increase along the streamwise direction, and the variation of the angles for large-scale structures is smaller than that for small-scale structures. Inspired by the coincidence of the increasing averaged inclination angle and the rise of the skin-friction coefficient, we propose a simple image-based model of the skin-friction coefficient. The model blends empirical formulae of the skin-friction coefficient in laminar and fully developed turbulent regions using the normalized averaged inclination angle of scalar structures at intermediate and small scales. The model prediction calculated from scalar images is validated by the results from the direct numerical simulation at two Mach numbers, 2.25 and 6, and the relative error can be less than 15 %.

Sign in / Sign up

Export Citation Format

Share Document