A Time-Marching Method for the Calculation of Nonsimilar 3D Boundary Layers on Turbomachinery Blades

1998 ◽  
Vol 120 (4) ◽  
pp. 799-807
Author(s):  
W. Asvapoositkul ◽  
M. Zangeneh
Keyword(s):  
Shear Stress ◽  
Boundary Layers ◽  
Entropy Generation ◽  
Analytical Data ◽  
Three Dimensional ◽  
Cross Flow ◽  
Steady State Solution ◽  
Design Stage ◽  
Impeller Blade ◽  
Turbomachinery Blades

A method is presented for the computation of three-dimensional boundary layers on turbomachinery blades. The method is based on a finite difference approach on a body-fitted curvilinear coordinate system, in which the time-dependent 3D boundary layer equations are marched in time until the steady-state solution is found. The method does not employ a similarity law and can therefore be applied to nonsimilar boundary layers. The method not only enables one to compute the skin friction and displacement of the boundary, but also provides information on the sources of entropy generation on the blades. The entropy generation is in fact split into three main components, which correspond to heat conduction, streamwise shear stress, and cross-flow shear stress. By considering each of the components of shear stress, at the design stage considerable insight can be found on the best way of modifying the blade geometry in order to reduce blade losses. The method is validated by comparison with analytical data for a laminar flat plate, experimental results for a helical blade in turbulent flow, and an axial compressor blade. Finally, the method is applied to the prediction of boundary layers on a subsonic centrifugal compressor impeller blade.

Three-dimensional instabilities in steady and unsteady non-parallel boundary layers, including effects of Tollmien-Schlichting disturbances and cross flow

1987 ◽  
Vol 409 (1837) ◽  
pp. 229-248 ◽  
Keyword(s):  
Boundary Layers ◽  
Large Scale ◽  
Three Dimensional ◽  
Steady Motion ◽  
Cross Flow ◽  
Parallel Flows ◽  
Roughness Elements ◽  
Tollmien Schlichting ◽  
Flow Effects ◽  
Secondary Instabilities

Three-dimensional (3D) linear stability properties are considered for steady and unsteady 2D or 3D boundary layers with significant non-parallelism present. Two main examples of such non-parallel flows whose stability is of interest are, firstly, steady motion, over roughness elements, in cross flow, or in large-scale separation and, secondly, unsteady 2D Tollmien-Schlichting (TS) motion, with its associated question of secondary instabilities. A high-frequency stability analysis is presented here. It is found that, for 2DTS or steady boundary layers, there is a swing in the direction of maximum TS spatial growth rate, from 0° for parallel flow towards 64.68° away from the free-stream direction, as the nonparallel flow effects increase. These effects then depend principally on, and indeed are proportional to, the local slope of the boundary-layer displacement. Cross flow can also have a profound impact on TS instabilities. Further implications for higher-amplitude and/or fasterscale disturbances, their secondary instability, and nonlinear interactions, are also discussed.

A Family of Hodograph Models for the Cross Flow Velocity Component of Three-Dimensional Turbulent Boundary Layers

1972 ◽  
Vol 94 (2) ◽  
pp. 321-329 ◽  
Author(s):  
J. R. Shanebrook ◽  
D. E. Hatch
Keyword(s):  
Flow Velocity ◽  
Boundary Layers ◽  
Velocity Component ◽  
Three Dimensional ◽  
Cross Flow ◽  
Turbulent Boundary Layers ◽  
Flow Profiles ◽  
Rectangular Channels ◽  
Cross Flow Velocity ◽  
The Cross

A family of hodograph models for the cross flow velocity component of three-dimensional, turbulent boundary layers is presented. The principal advantage of this family is its flexibility which allows a wide variety of possible shapes for the hodograph. An integral method based on this family is developed and applied to data obtained in curved, rectangular channels. For the cases treated, the method gives acceptable results for cross flow profiles with and without flow reversal. Suggestions for refining the method are given.

An Approach to Three-Dimensional Turbulent Boundary Layers

1966 ◽  
Author(s):  
A. D. Carmichael
Keyword(s):  
Boundary Layer ◽  
Boundary Layers ◽  
Shape Factor ◽  
Basic Assumption ◽  
Three Dimensional ◽  
Cross Flow ◽  
Turbulent Boundary Layers ◽  
Factor H ◽  
Simple Method ◽  
The Cross

A relatively simple method for predicting some of the characteristics of three-dimensional turbulent boundary layers is presented. The basic assumption of the method is that the cross-flow is small. An empirical correlation of a basic shape factor of the cross-flow boundary layer against the streamwise shape factor H is provided. This correlation, together with data for the streamwise boundary layer, is used to predict the cross flow. The solution is very sensitive to the accuracy of the streamwise boundary-layer data which is predicted by conventional two-dimensional methods.

Boundary Layers over Infinite Yawed Wings

1960 ◽  
Vol 11 (4) ◽  
pp. 333-347 ◽  
Author(s):  
J. C. Cooke
Keyword(s):  
Boundary Layer ◽  
Boundary Layers ◽  
Three Dimensional ◽  
Cross Flow ◽  
Turbulent Boundary Layers ◽  
Free Flow ◽  
Momentum Thickness ◽  
Displacement Thickness

SummaryA method of calculating turbulent boundary layers on infinite yawed wings is given, making use of a method of calculating turbulent boundary layers due to Spence and of an analogy between three-dimensional and axi-symmetric boundary layers. It is also shown that the displacement thickness is equal to that computed using chordwise components and that the streamwise momentum thickness is approximately equal to the chordwise momentum thickness. Shock-free flow and small boundary layer cross-flow are assumed.

Use of Surface Fences to Measure Wall Shear Stress in Three-dimensional Boundary Layers

1973 ◽  
Vol 24 (2) ◽  
pp. 87-91 ◽  
Author(s):  
J D Vagt ◽  
H Fernholz
Keyword(s):  
Shear Stress ◽  
Wall Shear Stress ◽  
Skin Friction ◽  
Boundary Layers ◽  
Manufacturing Process ◽  
Three Dimensional ◽  
Calibration Curves ◽  
Dimensional Boundary ◽  
Wall Shear

SummaryIf surface fences are to be applied for measuring skin friction in three-dimensional boundary layers they must be calibrated for both magnitude and direction of the shear stress. Results of the calibration for fences of different height are given. Furthermore, a manufacturing process and a mounting procedure are described to obtain surface fences with identical calibration curves.

Three-dimensional laminar boundary layers in crosswise pressure gradients

1974 ◽  
Vol 66 (4) ◽  
pp. 641-655 ◽  
Author(s):  
J. H. Horlock ◽  
A. K. Lewkowicz ◽  
J. Wordsworth
Keyword(s):  
Boundary Layer ◽  
Pressure Gradient ◽  
Boundary Layers ◽  
Free Stream ◽  
Three Dimensional ◽  
Cross Flow ◽  
Free Stream Velocity ◽  
Stream Velocity ◽  
Laminar Boundary Layers ◽  
The Cross

Two attempts were made to develop a three-dimensional laminar boundary layer in the flow over a flat plate in a curved duct, establishing a negligible streamwise pressure gradient and, at the same time, an appreciable crosswise pressure gradient.A first series of measurements was undertaken keeping the free-stream velocity at about 30 ft/s; the boundary layer was expected to be laminar, but appears to have been transitional. As was to be expected, the cross-flow in the boundary layer decreased gradually as the flow became progressively more turbulent.In a second experiment, at a lower free-stream velocity of approximately 10 ft/s, the boundary layer was laminar. Its streamwise profile resembled closely the Blasius form, but the cross-flow near the edge of the boundary layer appears to have exceeded that predicted theoretically. However, there was a substantial experimental scatter in the measurements of the yaw angle, which in laminar boundary layers is difficult to obtain accurately.

Turbulent flow between a rotating and a stationary disk

2001 ◽  
Vol 426 ◽  
pp. 297-326 ◽  
Author(s):  
MAGNE LYGREN ◽  
HELGE I. ANDERSSON
Keyword(s):  
Shear Stress ◽  
Boundary Layers ◽  
Coherent Structures ◽  
Three Dimensional ◽  
Two Dimensional ◽  
Mean Flow ◽  
Mean Velocity ◽  
Stationary Disk ◽  
Dimensional Boundary ◽  
The Mean

Turbulent flow between a rotating and a stationary disk is studied. Besides its fundamental importance as a three-dimensional prototype flow, such flow fields are frequently encountered in rotor–stator configurations in turbomachinery applications. A direct numerical simulation is therefore performed by integrating the time-dependent Navier–Stokes equations until a statistically steady state is reached and with the aim of providing both long-time statistics and an exposition of coherent structures obtained by conditional sampling. The simulated flow has local Reynolds number r2ω/v = 4 × 105 and local gap ratio s/r = 0.02, where ω is the angular velocity of the rotating disk, r the radial distance from the axis of rotation, v the kinematic viscosity of the fluid, and s the gap width.The three components of the mean velocity vector and the six independent Reynolds stresses are compared with experimental measurements in a rotor–stator flow configuration. In the numerically generated flow field, the structural parameter a1 (i.e. the ratio of the magnitude of the shear stress vector to twice the mean turbulent kinetic energy) is lower near the two disks than in two-dimensional boundary layers. This characteristic feature is typical for three-dimensional boundary layers, and so are the misalignment between the shear stress vector and the mean velocity gradient vector, although the degree of misalignment turns out to be smaller in the present flow than in unsteady three-dimensional boundary layer flow. It is also observed that the wall friction at the rotating disk is substantially higher than at the stationary disk.Coherent structures near the disks are identified by means of the λ2 vortex criterion in order to provide sufficient information to resolve a controversy regarding the roles played by sweeps and ejections in shear stress production. An ensemble average of the detected structures reveals that the coherent structures in the rotor–stator flow are similar to the ones found in two-dimensional flows. It is shown, however, that the three-dimensionality of the mean flow reduces the inter-vortical alignment and the tendency of structures of opposite sense of rotation to overlap. The coherent structures near the disks generate weaker sweeps (i.e. quadrant 4 events) than structures in conventional two-dimensional boundary layers. This reduction in the quadrant 4 contribution from the coherent structures is believed to explain the reduced efficiency of the mean flow in producing Reynolds shear stress.

Sign in / Sign up

Export Citation Format

Share Document