Secondary Flow Measurements in a Turbine Cascade With High Inlet Turbulence

1992 ◽  
Vol 114 (1) ◽  
pp. 173-183 ◽  
Author(s):  
D. G. Gregory-Smith ◽  
J. G. E. Cleak
Keyword(s):  
Flow Field ◽  
Secondary Flow ◽  
Flow Region ◽  
Shear Stresses ◽  
Reynolds Stresses ◽  
Mean Flow ◽  
Flow Measurements ◽  
Frequency Spectra ◽  
The Mean ◽  
End Wall

Measurements of the mean and turbulent flow field have been made in a cascade of high turning turbine rotor blades. The inlet turbulence was raised to 5 percent by a grid placed upstream of the cascade, and the secondary flow region was traversed within and downstream of the blades using a five-hole probe and crossed hot wires. Flow very close to the end wall was measured using a single wire placed at several orientations. Some frequency spectra of the turbulence were also obtained. The results show that the mean flow field is not affected greatly by the high inlet turbulence. The Reynolds stresses were found to be very high, particularly in the loss core. Assessment of the contributions to production of turbulence by the Reynolds stresses shows that the normal stresses have significant effects, as do the shear stresses. The calculation of eddy viscosity from two independent shear stresses shows it to be fairly isotropic in the loss core. Within the blade passage, the flow close to the end wall is highly skewed and exhibits generally high turbulence. The frequency spectra show no significant resonant peaks, except for one at very low frequency, attributable to an acoustic resonance.

Secondary Flow Measurements in a Turbine Cascade With High Inlet Turbulence

1990 ◽  
Author(s):  
D. G. Gregory-Smith ◽  
J. G. E. Cleak
Keyword(s):  
Flow Field ◽  
Secondary Flow ◽  
Flow Region ◽  
Shear Stresses ◽  
Reynolds Stresses ◽  
Mean Flow ◽  
Flow Measurements ◽  
Frequency Spectra ◽  
The Mean ◽  
End Wall

Measurements of the mean and turbulent flow field have been made in a cascade of high turning turbine rotor blades. The inlet turbulence was raised to 5% by a grid placed upstream of the cascade, and the secondary flow region was traversed within and downstream of the blades using a 5 hole probe and crossed hot-wires. Flow very close to the end wall was measured using a single wire placed at several orientations. Some frequency spectra of the turbulence were also obtained. The results shows that the mean flow field is not affected greatly by the high inlet turbulence. The Reynolds stresses were found to be very high, particularly in the loss core. Assessment of the contributions to production of turbulence by the Reynolds stresses show that the normal stresses have significant affects as well as the shear stresses. The calculation of eddy viscosity from two independent shear stresses show it to be fairly isotropic in the loss core. Within the blade passage, the flow close to the end wall is highly skewed and exhibits generally high turbulence. The frequency spectra show no significant resonant peaks, except for one at very low frequency, attributable to an acoustic resonance.

M. J. Hartmann Memorial Session Paper: Turbulence Characteristics in a Supersonic Cascade Wake Flow

1994 ◽  
Vol 116 (4) ◽  
pp. 586-596 ◽  
Author(s):  
P. L. Andrew ◽  
Wing-fai Ng
Keyword(s):  
Boundary Layer ◽  
Incidence Angle ◽  
Reynolds Numbers ◽  
Wake Flow ◽  
Shear Stresses ◽  
State University ◽  
Mean Flow ◽  
Flow Measurements ◽  
The Mean ◽  
Supersonic Wake

The turbulent character of the supersonic wake of a linear cascade of fan airfoils has been studied using a two-component laser-doppler anemometer. The cascade was tested in the Virginia Polytechnic Institute and State University intermittent wind tunnel facility, where the Mach and Reynolds numbers were 2.36 and 4.8 × 106, respectively. In addition to mean flow measurements, Reynolds normal and shear stresses were measured as functions of cascade incidence angle and streamwise locations spanning the near-wake and the far-wake. The extremities of profiles of both the mean and turbulent wake properties´ were found to be strongly influenced by upstream shock-boundary -layer interactions, the strength of which varied with cascade incidence. In contrast, the peak levels of turbulence properties within the shear layer were found to be largely independent of incidence, and could be characterized in terms of the streamwise position only. The velocity defect turbulence level was found to be 23 percent, and the generally accepted value of the turbulence structural coefficient of 0.30 was found to be valid for this flow. The degree of similarity of the mean flow wake profiles was established, and those profiles demonstrating the most similarity were found to approach a state of equilibrium between the mean and turbulent properties. In general, this wake flow may be described as a classical free shear flow, upon which the influence of upstream shock-boundary-layer interactions has been superimposed.

Effect of a Simulated Free Surface on the Wake of a Slender Body

1986 ◽  
Vol 30 (04) ◽  
pp. 242-255
Author(s):  
P. Mitra ◽  
W. Neu ◽  
J. Schetz
Keyword(s):  
Free Surface ◽  
Turbulent Flow ◽  
Normal Component ◽  
Image Plane ◽  
Axisymmetric Body ◽  
Transverse Component ◽  
Reynolds Stresses ◽  
Mean Flow ◽  
Flow Measurements ◽  
The Mean

Turbulent flow measurements were performed in the wake of a slender axisymmetric body in the presence of a flat plate strut and an image plane crudely representing the "rigid lid" approximation to a free surface. The tests were performed in a wind tunnel at a nominal Reynolds number of 6.0 ⨯ 105. A Yawhead probe was used for the mean flow measurements, and a Constant Temperature Anemometer System with an x-wire probe was used to obtain the turbulent flow characteristics. The presence of the image plane was found to increase the velocity defect and the static pressure as the image plane was approached. A redistribution among the various components of velocity fluctuations was noted near the image plane. The transverse component was enhanced at the expense of the normal component. The image plane also was found to influence the magnitudes and radial spread of turbulence intensities and Reynolds stresses. Some interactions between the wake of the axisymmetric body and that of the plate strut were observed. Overall, the mean velocities and the turbulence quantities indicated symmetry about the image plane throughout the wake.

scholarly journals Evolution and structure of sink-flow turbulent boundary layers

2001 ◽  
Vol 428 ◽  
pp. 1-27 ◽  
Author(s):  
M. B. JONES ◽  
IVAN MARUSIC ◽  
A. E. PERRY
Keyword(s):  
Boundary Layers ◽  
Velocity Profiles ◽  
Turbulent Boundary Layers ◽  
Reynolds Stresses ◽  
Mean Flow ◽  
Mean Velocity ◽  
Flow Measurements ◽  
Law Of The Wall ◽  
The Mean ◽  
Logarithmic Law

An experimental and theoretical investigation of turbulent boundary layers developing in a sink-flow pressure gradient was undertaken. Three flow cases were studied, corresponding to different acceleration strengths. Mean-flow measurements were taken for all three cases, while Reynolds stresses and spectra measurements were made for two of the flow cases. In this study attention was focused on the evolution of the layers to an equilibrium turbulent state. All the layers were found to attain a state very close to precise equilibrium. This gave equilibrium sink flow data at higher Reynolds numbers than in previous experiments. The mean velocity profiles were found to collapse onto the conventional logarithmic law of the wall. However, for profiles measured with the Pitot tube, a slight ‘kick-up’ from the logarithmic law was observed near the buffer region, whereas the mean velocity profiles measured with a normal hot wire did not exhibit this deviation from the logarithmic law. As the layers approached equilibrium, the mean velocity profiles were found to approach the pure wall profile and for the highest level of acceleration Π was very close to zero, where Π is the Coles wake factor. This supports the proposition of Coles (1957), that the equilibrium sink flow corresponds to pure wall flow. Particular interest was also given to the evolutionary stages of the boundary layers, in order to test and further develop the closure hypothesis of Perry, Marusic & Li (1994). Improved quantitative agreement with the experimental results was found after slight modification of their original closure equation.

Measurement of the Reynolds stresses and the mean-flow field in a three-dimensional pressure-driven boundary layer

1982 ◽  
Vol 119 ◽  
pp. 121-153 ◽  
Author(s):  
Udo R. Müller
Keyword(s):  
Boundary Layer ◽  
Shear Stress ◽  
Flow Field ◽  
Three Dimensional ◽  
Turbulent Shear ◽  
Reynolds Stresses ◽  
Mean Flow ◽  
Mean Velocity ◽  
Flow Acceleration ◽  
The Mean

An experimental study of a steady, incompressible, three-dimensional turbulent boundary layer approaching separation is reported. The flow field external to the boundary layer was deflected laterally by turning vanes so that streamwise flow deceleration occurred simultaneous with cross-flow acceleration. At 21 stations profiles of the mean-velocity components and of the six Reynolds stresses were measured with single- and X-hot-wire probes, which were rotatable around their longitudinal axes. The calibration of the hot wires with respect to magnitude and direction of the velocity vector as well as the method of evaluating the Reynolds stresses from the measured data are described in a separate paper (Müller 1982, hereinafter referred to as II). At each measuring station the wall shear stress was inferred from a Preston-tube measurement as well as from a Clauser chart. With the measured profiles of the mean velocities and of the Reynolds stresses several assumptions used for turbulence modelling were checked for their validity in this flow. For example, eddy viscosities for both tangential directions and the corresponding mixing lengths as well as the ratio of resultant turbulent shear stress to turbulent kinetic energy were derived from the data.

LDV Measurements of the Flow Field in the Nozzle Region of a Confined Double Annular Burner

2001 ◽  
Vol 123 (2) ◽  
pp. 228-236 ◽  
Author(s):  
Francois Schmitt ◽  
Birinchi K. Hazarika ◽  
Charles Hirsch
Keyword(s):  
Flow Field ◽  
Turbulent Flow ◽  
Turbulence Intensity ◽  
Meridional Plane ◽  
Reynolds Stresses ◽  
Mean Flow ◽  
Fine Grid ◽  
Contour Plots ◽  
The Mean ◽  
Grid Points

A database for the complex turbulent flow of a confined double annular burner in cold conditions is presented here. In the region close to the exit of the annular nozzles LDV measurements at 5515 grid points in the meridional plane were conducted. At each measurement position, validated data for 3000–16,000 particles were recorded, and the mean axial and radial velocities, axial and radial turbulence intensity and Reynolds stresses were computed. The resulting mean flow field is axisymmetric within an uncertainty of 2 percent. The contour plots of turbulent quantities on the fine grid, as well as the streamlines based on the mean flow field, are presented for the flow.

Some Effects of Non-Axisymmetric End Wall Profiling on Axial Flow Compressor Aerodynamics: Part I—Linear Cascade Investigation

2008 ◽  
Author(s):  
N. W. Harvey
Keyword(s):  
Flow Field ◽  
Secondary Flow ◽  
Computational Study ◽  
Design Method ◽  
Axial Flow ◽  
Flow Region ◽  
Original Design ◽  
Suction Surface ◽  
Secondary Loss ◽  
End Wall

Non-axisymmetric end wall profiling is now a well established design methodology in axial flow turbines, used principally to improve their aerodynamic efficiency by reducing secondary loss. However, profiled end walls (PEWs) have yet to find an in-service application in a gas turbine compressor. This two-part paper presents the results of a number of studies, both experimental and computational, into the potential aerodynamic benefits of applying PEWs in axial flow compressors. The first paper reports research carried out using a linear compressor stator cascade at Cambridge University. The datum geometry was based on previous research with this cascade. The PEW geometry was generated using a method that had been proven to reduce secondary loss in turbine blade rows. Data was taken on the datum and PEW geometries in the form of exit area traverses and surface static pressure measurements. The experiments demonstrated improvements to the exit flow field in terms of local reductions in the loss and under-turning in the secondary flow region due to the PEW. It was found that the original design method had over estimated the benefits of the PEW. The datum and PEW geometries were further analysed using state-of-the-art CFD (Computational Fluid Dynamics). The CFD is shown to achieve very good agreement with measurement at the design condition and a reasonable, qualitative match at off-design. It is concluded that the PEW geometry, though not optimum, effected predictable changes to the compressor stator flow field. The mechanisms for these effects are discussed and conclusions are drawn for taking the work forward. In particular, a mechanism is identified whereby the PEW enhances the cross-flow on the end wall and the subsequent radial migration of the secondary flow adjacent to the aerofoil suction surface. The control of corner stall by means of this flow mechanism is highlighted as a possible area for further investigation. This is followed up in the second paper, which presents a computational study of applying PEWs to a multi-stage HP compressor.

Turbulent Flow Over a NACA 4412 Airfoil at Angle of Attack 15 Degree

2003 ◽  
Author(s):  
O. O. Badran ◽  
H. H. Bruun
Keyword(s):  
Reverse Flow ◽  
Separation Bubble ◽  
Angle Of Attack ◽  
Flow Region ◽  
Shear Stresses ◽  
Separation Flow ◽  
Reynolds Stresses ◽  
Mean Flow ◽  
Trailing Edge ◽  
Short Period

This paper presents the measured mean flow and Reynolds stresses results, obtained on the center-line plane of the airfoil, covering the boundary layers over the upper surface, the potential flow region and the wake downstream of the trailing edge, at αa = 15°. The flying X-hot-wire probe was used to measure the U and V components of the flow field over the airfoil. An improved understanding of the physical characteristics of separation on the airfoil sections and in the region of the trailing edge is of direct value for the improvement of high lift wings for aircraft. From the study of the separation flow at angle of attack αa = 15°, the following can be concluded: (1) An intermittent reverse flow region occurred near the trailing edge of the airfoil. A separation bubble occurred for a short period of time and was then swept away with the stream wise flow. (2) The angle of attack αa = 15° corresponds to the position of maximum lift for a NACA 4412 airfoil section. (3) It is found that values of the Reynolds normal and shear stresses move away from the surface with downstream distance, and (4) In the wake region, relatively large values of Reynolds stresses occurred, which were related to the vertical oscillation in the lower wake.

Turbulence Characteristics in a Supersonic Cascade Wake Flow

1993 ◽  
Author(s):  
Philip L. Andrew ◽  
Wing-fai Ng
Keyword(s):  
Boundary Layer ◽  
Incidence Angle ◽  
Reynolds Numbers ◽  
Wake Flow ◽  
Shear Stresses ◽  
State University ◽  
Mean Flow ◽  
Flow Measurements ◽  
The Mean ◽  
Supersonic Wake

The turbulent character of the supersonic wake of a linear cascade of fan airfoils has been studied using a two–component Laser Doppler Anemometer. The cascade was tested in the Virginia Polytechnic Institute and State University intermittent wind tunnel facility, where the Mach and Reynolds numbers were 2.36 and 4.8 × 106, respectively. In addition to mean flow measurements, Reynolds normal and shear stresses were measured as functions of cascade incidence angle and streamwise locations spanning the near–wake and the far–wake. The extremities of profiles of both the mean and turbulent wake properties were found to be strongly influenced by upstream shock–boundary–layer–interactions, the strength of which varied with cascade incidence. In contrast, the peak levels of turbulence properties within the shear layer were found to be largely independent of incidence, and could be characterized in terms of the streamwise position only. The velocity defect turbulence level was found to be 23%, and the generally–accepted value of the turbulence structural coefficient of 0.30 was found to be valid for this flow. The degree of similarity of the mean flow wake profiles was established, and those profiles demonstrating the most similarity were found to approach a state of equilibrium between the mean and turbulent properties. In general, this wake flow may be described as a classical free shear flow, upon which the influence of upstream shock–boundary–layer–interactions has been superimposed.

Sign in / Sign up

Export Citation Format

Share Document