Time-Averaged Heat Transfer and Pressure Measurements and Comparison With Prediction for a Two-Stage Turbine

1994 ◽  
Vol 116 (1) ◽  
pp. 14-22 ◽  
Author(s):  
M. G. Dunn ◽  
J. Kim ◽  
K. C. Civinskas ◽  
R. J. Boyle
Keyword(s):  
Surface Pressure ◽  
Space Shuttle ◽  
Three Dimensional ◽  
Stanton Number ◽  
Navier Stokes ◽  
Pressure Measurements ◽  
Two Stage ◽  
Pressure Transducers ◽  
Pressure Distributions ◽  
Main Engine

Time-averaged Stanton number and surface-pressure distributions are reported for the first-stage vane row and the first-stage blade row of the Rocketdyne Space Shuttle Main Engine two-stage fuel-side turbine. These measurements were made at 10, 50, and 90 percent span on both the pressure and suction surfaces of the component. Stanton-number distributions are also reported for the second-stage vane at 50 percent span. A shock tube is used as a short-duration source of heated and pressurized air to which the turbine is subjected. Platinum thin-film gages are used to obtain the heat-flux measurements and miniature silicone-diaphragm pressure transducers are used to obtain the surface pressure measurements. The first-stage vane Stanton number distributions are compared with predictions obtained using a quasi-three dimensional Navier–Stokes solution and a version of STAN5. This same N–S technique was also used to obtain predictions for the first blade and the second vane.

Time-Averaged Heat Transfer and Pressure Measurements and Comparison With Prediction for a Two-Stage Turbine

1992 ◽  
Author(s):  
M. G. Dunn ◽  
J. Kim ◽  
K. C. Civinskas ◽  
R. J. Boyle
Keyword(s):  
Surface Pressure ◽  
Space Shuttle ◽  
Stanton Number ◽  
Navier Stokes ◽  
Pressure Measurements ◽  
Two Stage ◽  
Pressure Transducers ◽  
Pressure Distributions ◽  
Flux Measurements ◽  
Main Engine

Time-averaged Stanton number and surface-pressure distributions are reported for the first-stage vane row and the first-stage blade row of the Rocketdyne Space Shuttle Main Engine two-stage fuel-side turbine. These measurements were made at 10%, 50%, and 90% span on both the pressure and suction surfaces of the component. Stanton-number distributions are also reported for the second-stage vane at 50% span. A shock tube is used as a short-duration source of heated and pressurized air to which the turbine is subjected. Platinum thin-film pages are used to obtain the heat-flux measurements and miniature silicone-diaphragm pressure transducers are used to obtain the surface pressure measurements. The first-stage vane Stanton number distributions are compared with predictions obtained using a quasi-3D Navier-Stokes solution and a version of STAN5. This same N-S technique was also used to obtain predictions for the first blade and the second vane.

Phase-Resolved Surface Pressure and Heat-Transfer Measurements on the Blade of a Two-Stage Turbine

1995 ◽  
Vol 117 (4) ◽  
pp. 653-658 ◽  
Author(s):  
M. G. Dunn ◽  
C. W. Haldeman
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Surface Pressure ◽  
Space Shuttle ◽  
Pressure Measurements ◽  
Two Stage ◽  
Blade Row ◽  
Flux Measurements ◽  
Main Engine ◽  
Unsteady Pressure Measurements

Phase-resolved surface pressure, and unsteady pressure measurements are reported for the first-stage blade row of the Space Shuttle Main Engine two-stage fuel-side turbine. Measurements were made at 10, 50, and 90 percent span on both the pressure and suction surfaces of the blade. Phase-resolved and unsteady heat-flux measurements are also reported.

Three Dimensional Unsteady Pressure Measurements for an Oscillating Turbine Blade

1997 ◽  
Author(s):  
D. L. Bell ◽  
L. He
Keyword(s):  
Turbine Blade ◽  
Surface Pressure ◽  
Three Dimensional ◽  
Test Facility ◽  
Pressure Measurements ◽  
Blade Surface ◽  
Low Speed ◽  
Pressure Transducers ◽  
Bending Mode ◽  
Oscillation Frequencies

A complete set of unsteady blade surface pressure measurements is presented for a single turbine blade oscillating in a three dimensional bending mode. Results are provided for five spanwise sections at 10%, 30%, 50%, 70% and 90% of span. Steady blade pressure measurements and five-hole probe traverses at the inlet and exit planes of the test section, are also included. The test facility operates at low speed and the working section consists of a single turbine blade mounted in a profiled duct. A rigid blade with constant section was used, and a three dimensional bending mode realised by hinging the blade at root and driving the tip section. The low speed and scale of the test facility allowed low oscillation frequencies (5 to 20 Hz) to be employed, in order to match realistic reduced frequencies. This enabled the unsteady blade surface pressure response to be recorded with externally mounted pressure transducers. The validity of this technique is examined. Results from the test facility demonstrate a noticeable three dimensional behaviour of the unsteady flow.

The Effect of Vane Clocking on the Unsteady Flowfield in a One and a Half Stage Transonic Turbine

2007 ◽  
Author(s):  
O. Schennach ◽  
R. Pecnik ◽  
B. Paradiso ◽  
E. Go¨ttlich ◽  
A. Marn ◽  
...  
Keyword(s):  
Laser Doppler Velocimetry ◽  
Three Dimensional ◽  
Fast Response ◽  
Navier Stokes ◽  
Doppler Velocimetry ◽  
Pressure Transducers ◽  
Wake Interactions ◽  
Transonic Turbine ◽  
Response Pressure ◽  
Vane Clocking

The current paper presents the results of numerical and experimental clocking investigations performed in a high-pressure transonic turbine with a downstream vane row. The objective was a detailed analysis of shock and wake interactions in such a 1.5 stage machine while clocking the vanes. Therefore a transient 3D-Navier Stokes calculation was done for two clocking positions and the three dimensional results are compared with Laser-Doppler-Velocimetry measurements at midspan. Additionally the second vane was equipped with fast response pressure transducers to record the instantaneous surface pressure for 20 different clocking positions at midspan.

Investigations of the Effect of Annulus Taper on Transonic Turbine Cascade Flow

1986 ◽  
Vol 108 (2) ◽  
pp. 285-292 ◽  
Author(s):  
W. Bra¨unling ◽  
F. Lehthaus
Keyword(s):  
Surface Pressure ◽  
Theoretical Calculations ◽  
Three Dimensional ◽  
Computer Code ◽  
Numerical Results ◽  
Test Facility ◽  
Turbine Cascade ◽  
Pressure Distributions ◽  
Aspect Ratios ◽  
Wide Range

In a test facility for rotating annular cascades with three conical test sections of different taper angles (0, 30, 45 deg), experiments are conducted for two geometrically different turbine cascade configurations, a hub section cascade with high deflection and a tip section cascade with low deflection. The evaluation of time-averaged data derived from conventional probe measurements upstream and downstream of the test wheel in the machine-fixed absolute system is based on the assumption of axisymmetric stream surfaces. The cascade characteristics, i.e., mass flow, deflection, and losses, for a wide range of inlet flow angles and outlet Mach numbers are provided in the blade-fixed relative system with respect to the influence of annulus taper. Some of the results are compared with simple theoretical calculations. To obtain some information about the spatial structure of the flow within the cascade passages, surface pressure distributions on the profiles of the rotating test wheels are measured at three different radial blade sections. For some examples those distributions are compared with numerical results on plane cascades of the same sweep and dihedral angles and the same aspect ratios. The computer code used is based on a three-dimensional time-marching finite-volume method solving the Euler equations. Both experimental and numerical results show a fairly good qualitative agreement in the three-dimensional blade surface pressure distributions. This work will be continued with detailed investigations on the spatial flow structure.

Shroud Leakage Modeling of the Flow in a Two Stage Axial Test Turbine

2008 ◽  
Author(s):  
M. Pau ◽  
F. Cambuli ◽  
N. Mandas
Keyword(s):  
Three Dimensional ◽  
Design Tool ◽  
Navier Stokes ◽  
Computational Time ◽  
Leakage Flow ◽  
Two Stage ◽  
Flow Paths ◽  
Flow Interaction ◽  
Full Calculation ◽  
Mainstream Flow

Three dimensional steady multistage calculations, using mixing plane approach, are presented for two different blade geometries in a two stage axial test turbine with shrouded blades. A 3D multiblock Navier-Stokes finite volume solver (TBLOCK) has been used in all the simulations. In order to study shroud leakage flow effects the whole shroud cavity geometry has been modeled, overcoming most of the limitations of simple shroud leakage model in calculating fluid flow over complex geometries. Numerical investigations are mainly focused on assessing the ability of the solver to be used as multistage design tool for modeling leakage-mainstream flow interaction. Several calculations are compared. The first computes the main blade flow path with no modeling of the shroud cavities. The second includes the modeling of the shroud cavities for a zero leakage mass flow rate. Finally a multiblock calculation which models all the leakage flow paths and shroud cavities has been carried out for two different levels of shroud seal clearance. It is found that neglecting shroud leakage significantly alters the computed velocity profiles and loss distributions, for both the computed blade geometries. A numerically predicted shroud leakage offset loss is presented for the two considered blade geometries, focusing on the relative importance of the leakage flow, re-entry mixing losses, and inlet and exit shroud cavity effect. Results demonstrates that full calculation of leakage flow paths and cavities is required to obtain reliable results, indicating the different effects of the leakage-to-mainstream flow interaction on the blade geometries computed. Despite a slight increase in the computational time, multiblock approach in handling leakage flow problem can now-days be used as a practical tool in the blade design process and routine shroud leakage calculations.

Centrifugal Compressor Impeller Aerodynamics: An Experimental Investigation

1990 ◽  
Author(s):  
H. David Joslyn ◽  
Joost J. Brasz ◽  
Robert P. Dring
Keyword(s):  
Flow Visualization ◽  
Centrifugal Compressor ◽  
Flow Analysis ◽  
Three Dimensional ◽  
Companion Paper ◽  
Surface Flow ◽  
Navier Stokes ◽  
Pressure Distributions ◽  
Compressor Impeller ◽  
Surface Flow Visualization

The ability to acquire blade loadings (surface pressure distributions) and surface flow visualization on an unshrouded centrifugal compressor impeller is demonstrated. Circumferential and streamwise static pressure distributions acquired on the stationary shroud are also presented. Data was acquired in a new facility designed for centrifugal compressor aerodynamic research. Blade loadings calculated with a blade–to–blade potential flow analysis are compared with the measured results. Surface flow visualization reveals some complex aspects of the flow on the surface of the impeller blading and hub. In a companion paper, Dorney and Davis (1990), a state–of–the–art, three–dimensional, time–accurate, Navier Stokes prediction of the flow through the impeller is presented.

Numerical analysis of the three-dimensional flow in the main injector assembly of the Space Shuttle Main Engine

1986 ◽  
Author(s):  
T. MUKERJEE ◽  
A. PRZKEWAS ◽  
R. HOLLAND ◽  
N. COSTES
Keyword(s):  
Numerical Analysis ◽  
Space Shuttle ◽  
Three Dimensional ◽  
Three Dimensional Flow ◽  
Dimensional Flow ◽  
Main Engine
Sign in / Sign up

Export Citation Format

Share Document