A New Concept for High Temperature Fuel Cell Hybrid Systems Using Supercritical Carbon Dioxide

2009 ◽  
Vol 6 (2) ◽  
Author(s):  
D. Sánchez ◽  
R. Chacartegui ◽  
F. Jiménez-Espadafor ◽  
T. Sánchez
Keyword(s):  
Carbon Dioxide ◽  
Fuel Cells ◽  
High Temperature ◽  
Fuel Cell ◽  
Supercritical Carbon Dioxide ◽  
Hybrid Systems ◽  
Cell Hybrid ◽  
Gas Turbines ◽  
Solid Oxide ◽  
Molten Carbonate

Hybrid power systems based on high temperature fuel cells are a promising technology for the forthcoming distributed power generation market. For the most extended configuration, these systems comprise a fuel cell and a conventional recuperative gas turbine engine bottoming cycle, which recovers waste heat from the cell exhaust and converts it into useful work. The ability of these gas turbines to produce useful work relies strongly on a high fuel cell operating temperature. Thus, if molten carbonate fuel cells or the new generation intermediate temperature solid oxide fuel cells are used, the efficiency and power capacity of the hybrid system decrease dramatically. In this work, carbon dioxide is proposed as the working fluid for a closed supercritical bottoming cycle, which is expected to perform better for intermediate temperature heat recovery applications than the air cycle. Elementary fuel cell lumped-volume models for both solid oxide and molten carbonate are used in conjunction with a Brayton cycle thermodynamic simulator capable of working with open/closed and air/carbon dioxide systems. This paper shows that, even though the new cycle is coupled with an atmospheric fuel cell, it is still able to achieve the same overall system efficiency and rated power than the best conventional cycles being currently considered. Furthermore, under certain operating conditions, the performance of the new hybrid systems beats that of existing pressurized fuel cell hybrid systems with conventional gas turbines. From the results, it is concluded that the supercritical carbon dioxide bottoming cycle holds a very high potential as an efficient power generator for hybrid systems. However, costs and balance of plant analysis will have to be carried out in the future to check its feasibility.

Hybrid Gas Turbine and Fuel Cell Systems in Perspective Review

1999 ◽  
Author(s):  
David J. White
Keyword(s):  
Carbon Dioxide ◽  
Fuel Cells ◽  
High Temperature ◽  
Fuel Cell ◽  
Gas Turbine ◽  
Hybrid Systems ◽  
Gas Turbines ◽  
Energy Output ◽  
Net Energy ◽  
Cell Systems

The concept of hybrids combining fuel cell and gas turbine systems is without question neoteric, and probably is less than eight years old. However, this concept is in a sense a logical development derived from the many early systems that embodied the key features of rotating machinery to compress air. It was the introduction of high temperature fuel cells such as the solid oxide fuel cell (SOFC) that allowed the concept of hybrid gas turbine fuel cell systems to take root. The SOFC with an operating temperature circa 1000° C matched well with small industrial gas turbines that had firing temperatures on the same order. The recognition that the SOFC could be substituted for the gas turbine combustor was the first step into the realm of fuel cell topping systems. Fuel cells in general were recognized as having higher efficiencies at elevated pressures. Thus the hybrid topping system where the gas turbine pressurized the fuel cell and the fuel cell supplied the hot gases for expansion over the turbine promised to provide a high level of synergy between the two systems. Bottoming systems using the exhaust of a gas turbine as the working fluid of a fuel cell such as the molten carbonate fuel cell (MCFC) have been identified and are potential future power generation hybrid systems. The MCFC is especially well suited to the bottoming role because of the need to have carbon dioxide present in the inlet air stream. The carbon dioxide in the gas turbine exhaust allows the high temperature blower, normally used to recirculate and inject exhaust products into the inlet air, to be eliminated. Hybrid systems have the potential of achieving fossil fuel to electricity conversion efficiencies on the order of 70% and higher. The costs of hybrid systems in dollars per kilowatt are generally higher than say an advanced gas turbine that is available today but not by much. The net energy output over the life of a hybrid topping system is similar to that of a recuperated gas turbine but possibly lower than a high-efficiency simple-cycle machine, depending on the efficiency of the hybrid. Methodologies to aid in the selection of the hybrid system for future development have to be developed and used consistently. Life cycle analyses (LFA) provide a framework for such selection processes. In particular the concept of net energy output provides a mechanism to assign relative worth to competing concepts.

Performance Analysis on SOFC-HCCI Engine Hybrid System

2012 ◽  
Author(s):  
Sung Ho Park ◽  
Young Duk Lee ◽  
Sang Gyu Kang ◽  
Kook Young Ahn
Keyword(s):  
Fuel Cells ◽  
Fuel Cell ◽  
Hybrid Systems ◽  
Hybrid System ◽  
Gas Turbines ◽  
Waste Heat ◽  
Metal Catalyst ◽  
Molten Carbonate ◽  
Hcci Engine ◽  
Ci Engines

Fuel cell systems are currently regarded as a promising type of energy conversion system. Various types of fuel cell have been developed and investigated worldwide for portable, automotive, and stationary applications. In particular, in the case of large-scale stationary applications, the high-temperature fuel cells known as the molten carbonate fuel cell (MCFC) and the solid oxide fuel cell (SOFC) have been used as a power source due to their higher efficiency compared to low-temperature fuel cells. Because SOFCs have many advantages, including a high power density, low corrosion, and operability without a metal catalyst, many efforts to develop a SOFC hybrid system have been undertaken. SOFC hybrid systems with a gas turbine or engine show improved system efficiency through their utilization of waste heat and unreacted fuel. Especially, the internal combustion engine has the advantage of robustness, easy maintenance, and a low cost compared to gas turbines, this type is more adaptable for use in a hybrid system with a SOFC. However, the engine should be operated stably at a high air fuel ratio because the SOFC anode exhaust gas has a low fuel concentration. The homogeneous charge compression ignition (HCCI) engine has both the advantages of SI and CI engines. Moreover, the lean burn characteristics of the HCCI engine make it a strong candidate for SOFC hybrid systems. The objective of this work is to develop a novel cycle composed of a SOFC and a HCCI engine. In order to optimize the SOFC-HCCI hybrid system, a system analysis is conducted here using the commercial software Aspen Plus®. The SOFC model is validated with experimental data. The engine model is developed based on an empirical equation that considers the ignition delay time. The performance of the hybrid system is compared with that of a SOFC stand-alone system to confirm the optimization of the system. This study will be useful for the development of a new type of hybrid system which uses a fuel cell and an optimized system.

Power Cycle Integration and Efficiency Increase of Molten Carbonate Fuel Cell Systems

2005 ◽  
Vol 3 (4) ◽  
pp. 375-383 ◽  
Author(s):  
Petar Varbanov ◽  
Jiří Klemeš ◽  
Ramesh K. Shah ◽  
Harmanjeet Shihn
Keyword(s):  
Fuel Cells ◽  
High Temperature ◽  
Fuel Cell ◽  
Gas Turbines ◽  
Waste Heat ◽  
Combined Cycle ◽  
Molten Carbonate Fuel Cell ◽  
Steam Turbines ◽  
Molten Carbonate ◽  
Carbonate Fuel Cell

A new view is presented on the concept of the combined cycle for power generation. Traditionally, the term “combined cycle” is associated with using a gas turbine in combination with steam turbines to better utilize the exergy potential of the burnt fuel. This concept can be broadened, however, to the utilization of any power-generating facility in combination with steam turbines, as long as this facility also provides a high-temperature waste heat. Such facilities are high temperature fuel cells. Fuel cells are especially advantageous for combined cycle applications since they feature a remarkably high efficiency—reaching an order of 45–50% and even close to 60%, compared to 30–35% for most gas turbines. The literature sources on combining fuel cells with gas and steam turbines clearly illustrate the potential to achieve high power and co-generation efficiencies. In the presented work, the extension to the concept of combined cycle is considered on the example of a molten carbonate fuel cell (MCFC) working under stationary conditions. An overview of the process for the MCFC is given, followed by the options for heat integration utilizing the waste heat for steam generation. The complete fuel cell combined cycle (FCCC) system is then analyzed to estimate the potential power cost levels that could be achieved. The results demonstrate that a properly designed FCCC system is capable of reaching significantly higher efficiency compared to the standalone fuel cell system. An important observation is that FCCC systems may result in economically competitive power production units, comparable with contemporary fossil power stations.

Comparative Analysis of Hybrid Cycles Based on Molten Carbonate and Solid Oxide Fuel Cells

2001 ◽  
Author(s):  
Stefano Campanari ◽  
Ennio Macchi
Keyword(s):  
Fuel Cells ◽  
Fuel Cell ◽  
Gas Turbines ◽  
Solid Oxide ◽  
Molten Carbonate Fuel Cell ◽  
Small Scale ◽  
Oxide Fuel ◽  
Molten Carbonate ◽  
Successful Operation ◽  
Hybrid Plants

High temperature fuel cells are experiencing an increasing amount of attention thanks to the successful operation of prototype plants, including a multi-MW Molten Carbonate Fuel Cell (MCFC) demonstration plant and a hybrid Solid Oxide Fuel Cell (SOFC) gas turbine power plant. Both MCFCs and SOFCs are currently considered attractive for the integration with gas turbines in more complex “hybrid” plants, with projected performances that largely exceed combined cycles efficiencies even at a small-scale size and with an extremely low environmental impact. This paper compares the performances of MCFC and SOFC hybrid cycles. The comparison shows some advantages for the SOFC hybrid cycle in terms of plant simplicity and moderately higher efficiency.

scholarly journals Exploring the Possibility of Using Molten Carbonate Fuel Cell for the Flexible Coproduction of Hydrogen and Power

2021 ◽  
Vol 9 ◽  
Author(s):  
Utkarsh Shikhar ◽  
Kas Hemmes ◽  
Theo Woudstra
Keyword(s):  
Fuel Cells ◽  
High Temperature ◽  
Fuel Cell ◽  
Solid Oxide Fuel Cell ◽  
Solid Oxide ◽  
Oxide Fuel ◽  
Fuel Utilization ◽  
Molten Carbonate ◽  
Internal Reforming ◽  
Molten Carbonate Fuel Cells

Fuel cells are electrochemical devices that are conventionally used to convert the chemical energy of fuels into electricity while producing heat as a byproduct. High temperature fuel cells such as molten carbonate fuel cells and solid oxide fuel cells produce significant amounts of heat that can be used for internal reforming of fuels such as natural gas to produce gas mixtures which are rich in hydrogen, while also producing electricity. This opens up the possibility of using high temperature fuel cells in systems designed for flexible coproduction of hydrogen and power at very high system efficiency. In a previous study, the flowsheet software Cycle-Tempo has been used to determine the technical feasibility of a solid oxide fuel cell system for flexible coproduction of hydrogen and power by running the system at different fuel utilization factors (between 60 and 95%). Lower utilization factors correspond to higher hydrogen production while at a higher fuel utilization, standard fuel cell operation is achieved. This study uses the same basis to investigate how a system with molten carbonate fuel cells performs in identical conditions also using Cycle-Tempo. A comparison is made with the results from the solid oxide fuel cell study.

Parametric Analysis and Optimization of a High Temperature Fuel Cell: Supercritical CO2 Turbine Hybrid System

2008 ◽  
Author(s):  
D. Sa´nchez ◽  
R. Chacartegui ◽  
A. Mun˜oz ◽  
T. Sa´nchez
Keyword(s):  
Fuel Cells ◽  
High Temperature ◽  
Fuel Cell ◽  
Hybrid Systems ◽  
Hybrid System ◽  
Operating Temperature ◽  
Inlet Temperature ◽  
Brayton Cycle ◽  
Molten Carbonate ◽  
Turbine Inlet Temperature

The integration of high temperature fuel cells — molten carbonate and solid oxide — and gas turbine engines for efficient power generation is not new. Different strategies for integrating both systems have been proposed in the past ten years and there are some field tests being run presently. However, the commercial availability of such power systems seems to be continuously delayed, probably due to cost and reliability problems. The materials used in high temperature fuel cells are expensive and their cost is not decreasing at the expected pace. In fact, it looks as if they had reached stabilization. Therefore, there seems to be agreement that operating at a lower temperature might be the only way to achieve more competitive costs to enter the market, as metallic materials could then be used. From the point of view of conventional hybrid systems, decreasing the operating temperature of the cell would affect the efficiency of the bottoming cycle dramatically, as long as turbine inlet temperature is a critical parameter for the performance of a Brayton cycle. This is the reason why hybrid systems perform better with solid oxide fuel cells operating at 1000 °C than with molten carbonate cells at 650 °C typically. This work presents a hybrid system comprising a high temperature fuel cell, either SOFC or MCFC, and a bottoming Brayton cycle working with supercritical carbon dioxide. A parametric analysis is done where all the parameters affecting the performance of the hybrid system are studied, with emphasis in the bottoming cycle. For the Brayton cycle: pressure ratio, expansion and compression efficiencies, recuperator effectiveness, pressure losses, turbine inlet temperature... For the fuel cell: fuel utilization, current density, operating temperature, etc. From this analysis, optimum operating point and integration scheme are established and, after this, a comparison with conventional hybrid systems using similar fuel cells is done. Results show that, although the fuel cell is not pressurized in the CO2 based system, its performance is similar to the best conventional cycle. Furthermore, if lower operating temperatures are considered for the fuel cell, the new system performs better than any of the conventional.

Comparison of Molten Carbonate and Solid Oxide Fuel Cells for Integration in a Hybrid System for Cogeneration or Tri-Generation

2004 ◽  
Author(s):  
Georgia C. Karvountzi ◽  
Clifford M. Price ◽  
Paul F. Duby
Keyword(s):  
Fuel Cells ◽  
Fuel Cell ◽  
Solid Oxide Fuel Cells ◽  
Steam Turbine ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Solid Oxide ◽  
Oxide Fuel ◽  
Molten Carbonate ◽  
Hybrid Cycle

High temperature fuel cells, such as molten carbonate fuel cells (MCFC) and solid oxide fuel cells (SOFC) can be integrated in a hybrid cycle with a gas turbine and a steam turbine and achieve overall lower heating value (LHV) efficiencies of about 70%. A hybrid cycle designed for cogeneration or tri-generation applications could lead to even higher overall LHV efficiencies. Tri-generation is the combined generation of power, heat and cooling from the same fuel source. The purpose of the present paper is to compare the performance of a 20MW MCFC system and a 20MW tubular SOFC system and assess their potential to cogeneration and tri-generation applications. The system includes a fuel cell, a gas turbine, a multiple pressure heat recovery steam generator (HRSG), a steam turbine and an absorption chiller (for cooling). The systems were designed and sized using GatecycleTM heat balance software by GE Enter Software, LLC. In order to optimize each system we developed curves showing LHV “electric” and “cogeneration” efficiency versus power for different ratios of “MCFC and SOFC fuel cell-to-gas turbines size.” At atmospheric pressure and at 675°C (1247°F) the 20MW MCFC system achieves “electric” efficiency of 69.5%. The SOFC at the same pressure and at 980°C achieves 67.3% “electric” efficiency. The MCFC alone is more efficient (58%) than the SOFC alone (56%). However the SOFC produces more heat than the MCFC leading to slightly higher cogeneration and tri-generation efficiencies. Pressurized operation at 9atm boosts the performance of the SOFC system to higher efficiencies (70.5%). Pressurized operation is problematic for the MCFC due to increased cathode corrosion leading to cathode dissolution as well as sealant and interconnection problems. However we can pressurize the MCFC system independently of the fuel cell with the integration of a gas turbine with a compressor pressure ratio of 10 to 16. Thus we achieve efficiencies close to 69%. In conclusion SOFC is more efficiently integrated in a hybrid configuration with gas turbine and a steam turbine for trigeneration applications when pressurized. MCFC is more efficiently integrated at atmospheric and pressures below 6 atm.

Sign in / Sign up

Export Citation Format

Share Document