Heat Transfer Characteristics of a Swirling Laminar Impinging Jet

2009 ◽  
Vol 132 (1) ◽  
Author(s):  
Koichi Ichimiya ◽  
Koji Tsukamoto
Keyword(s):  
Heat Transfer ◽  
Three Dimensional ◽  
Local Heat Transfer ◽  
Impinging Jet ◽  
Local Heat ◽  
Experimental Results ◽  
Governing Equations ◽  
Constant Wall Temperature ◽  
Numerical Heat Transfer ◽  
Narrow Space

This paper describes the characteristics of the heat transfer and flow of a swirling laminar impinging jet in a comparatively narrow space with a confined wall. Air is impinged on a flat surface with constant wall temperature. The heat transfer and flow field were analyzed numerically by solving three-dimensional governing equations. Heat transfer experiment and flow visualization were also performed. Numerical heat transfer was compared with experimental results. Temperature distribution and velocity vectors in the space were obtained for various swirl numbers at Reynolds number Re=2000. The numerical and experimental results show that the swirling jet enhances or depresses the local heat transfer, and the average Nusselt number ratio with and without swirl takes a peak at a certain swirl number.

scholarly journals Numerical heat transfer analysis of micro-scale jet-impingement cooling in a high-pressure turbine vane

2021 ◽  
Author(s):  
Karan Anand
Keyword(s):  
Heat Transfer ◽  
Three Dimensional ◽  
Jet Impingement ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Heat Transfer Analysis ◽  
Transfer Rates ◽  
Numerical Heat Transfer ◽  
Turbine Vane ◽  
Single Jet

This research provides a computational analysis of heat transfer due to micro jet-impingement inside a gas turbine vane. A preliminary-parametric analysis of axisymmetric single jet was reported to better understand micro jet-impingement. In general, it was seen that as the Reynolds number increased the Nusselt number values increased. The jet to target spacing had a considerably lower impact on the heat transfer rates. Around 30% improvement was seen by reducing the diameter to half while changing the shape to an ellipse saw 20.8% improvement in Nusselt value. The numerical investigation was then followed by studying the heat transfer characteristics in a three-dimensional, actual-shaped turbine vane. Effects of jet inclination showed enhanced mixing and secondary heat transfer peaks. The effect of reducing the diameter of the jets to 0.125 mm yielded 55% heat transfer improvements compared to 0.51 mm; the tapering effect also enhanced the local heat transfer values as local velocities at jet exit increased.

Numerical Analysis of Local Heat Transfer From a Flat Plate to a Swirling Air Impingining Jet

2006 ◽  
Author(s):  
X. Terry Yan ◽  
Rahul S. Kalvakota
Keyword(s):  
Heat Transfer ◽  
Flat Plate ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Local Heat Transfer ◽  
Impinging Jet ◽  
Local Heat ◽  
Flow Profile ◽  
Transfer Coefficients ◽  
Stagnation Region

Local heat transfer from a flat plate to a swirling circular air impinging jet is investigated numerically. Reynolds Averaged Navier-Stokes equations (RANS) and energy equation are solved for the axisymmetric, three dimensional flow. Eddy-viscosity based turbulence models, RNG and V2F, are used. Non-uniform meshes are used for the three dimensional flows and mesh independent solutions are obtained. The flow Reynolds number, which is based on the jet diameter, is kept at 23,000. In the analysis, local heat transfer coefficients are obtained for different swirl numbers, S = 0.21, 0.35 and 0.47 and jet-to-plate distance, L/D, ranging from 2 to 9. Investigation of the effect of swirl flow profile at the exiting plane of the jet on heat transfer is also presented. It is found that different swirl profiles with the same swirl number lead to very different heat transfer behaviors in the stagnation region of the impinging jet.

scholarly journals Numerical heat transfer analysis of micro-scale jet-impingement cooling in a high-pressure turbine vane

2021 ◽  
Author(s):  
Karan Anand
Keyword(s):  
Heat Transfer ◽  
Three Dimensional ◽  
Jet Impingement ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Heat Transfer Analysis ◽  
Transfer Rates ◽  
Numerical Heat Transfer ◽  
Turbine Vane ◽  
Single Jet

This research provides a computational analysis of heat transfer due to micro jet-impingement inside a gas turbine vane. A preliminary-parametric analysis of axisymmetric single jet was reported to better understand micro jet-impingement. In general, it was seen that as the Reynolds number increased the Nusselt number values increased. The jet to target spacing had a considerably lower impact on the heat transfer rates. Around 30% improvement was seen by reducing the diameter to half while changing the shape to an ellipse saw 20.8% improvement in Nusselt value. The numerical investigation was then followed by studying the heat transfer characteristics in a three-dimensional, actual-shaped turbine vane. Effects of jet inclination showed enhanced mixing and secondary heat transfer peaks. The effect of reducing the diameter of the jets to 0.125 mm yielded 55% heat transfer improvements compared to 0.51 mm; the tapering effect also enhanced the local heat transfer values as local velocities at jet exit increased.

Three-Dimensional Heat Transfer of a Confined Circular Impinging Jet With Buoyancy Effects

2003 ◽  
Vol 125 (2) ◽  
pp. 250-256 ◽  
Author(s):  
Koichi Ichimiya ◽  
Yoshio Yamada
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Impinging Jet ◽  
Local Heat ◽  
Recirculation Flow ◽  
Narrow Space ◽  
Impingement Surface

This paper describes the heat transfer and flow characteristics of a single circular laminar impinging jet including buoyancy force in a comparatively narrow space with a confined wall. Temperature distribution and velocity vectors in the space were obtained numerically by solving three-dimensional governing equations for the Reynolds number Re=umD/ν=400-2000 and the dimensionless space, H=h/D=0.25-1.0. After impingement, heat transfer behavior on the impingement surface is divided into a forced convection region, a mixed convection region, and a natural convection region in the radial direction. The local heat flux corresponding to these three regions was visualized using a thermosensitive liquid crystal. Moreover, with the increase in Reynolds number, Re, and dimensionless space, H, the recirculation flow on the impingement surface moves downstream and its volume increases correspondingly. The Nusselt number averaged from r=0 to the minimum point of peripherally averaged Nusselt number, Num, was evaluated as a function of Re and H.

Three-Dimensional Natural Convection From Vertical Heated Plates With Adjoining Cool Surfaces

1992 ◽  
Vol 114 (1) ◽  
pp. 115-120 ◽  
Author(s):  
B. W. Webb ◽  
T. L. Bergman
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Control Volume ◽  
Three Dimensional ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Uniform Heat Flux ◽  
Infrared Thermal Imaging ◽  
Transfer Rates ◽  
Thermal Boundary Conditions

Natural convection in an enclosure with a uniform heat flux on two vertical surfaces and constant temperature at the adjoining walls has been investigated both experimentally and theoretically. The thermal boundary conditions and enclosure geometry render the buoyancy-induced flow and heat transfer inherently three dimensional. The experimental measurements include temperature distributions of the isoflux walls obtained using an infrared thermal imaging technique, while the three-dimensional equations governing conservation of mass, momentum, and energy were solved using a control volume-based finite difference scheme. Measurements and predictions are in good agreement and the model predictions reveal strongly three-dimensional flow in the enclosure, as well as high local heat transfer rates at the edges of the isoflux wall. Predicted average heat transfer rates were correlated over a range of the relevant dimensionless parameters.

Local Heat Transfer Characteristics in Simulated Electronic Modules

2003 ◽  
Vol 125 (3) ◽  
pp. 362-368 ◽  
Author(s):  
Seong-Yeon Yoo ◽  
Jong-Hark Park ◽  
Min-Ho Chung
Keyword(s):  
Heat Transfer ◽  
Mass Transfer ◽  
Three Dimensional ◽  
Vortex Generator ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Two Dimensional ◽  
Heat Transfer Characteristics ◽  
Dimensional Array ◽  
Transfer Characteristics

When heat is released by forced convection from electronic modules in a narrow printed circuit board channel, complex flow phenomena—such as stagnation and acceleration on the front surface, separation and reattachment on the top surface, wake or cavity flow near the rear surface—affect the heat transfer characteristics. The purpose of this study is to investigate how these flow conditions influence the local heat transfer from electronic modules. Experiments are performed on a three-dimensional array of hexahedral elements as well as on a two-dimensional array of rectangular elements. Naphthalene sublimation technique is employed to measure three-dimensional local mass transfer, and the mass transfer data are converted to their counterparts of the heat transfer process using the analogy equation between heat and mass transfer. Module location and streamwise module spacing are varied, and the effect of vortex generators on heat transfer enhancement is also examined. Dramatic change of local heat transfer coefficients is found on each surface of the module, and three-dimensional modules have a little higher heat transfer value than two-dimensional modules because of bypass flow. Longitudinal vortices formed by vortex generator enhance the mixing of fluids and thereby heat transfer, and the rectangular wing type vortex generator is found to be more effective than the delta wing type vortex generator.

Three-Dimensional Transient Heat Conduction Equation Solution for Accurate Quantification of Heat Transfer Coefficient in Transient Liquid Crystal Experiments

2019 ◽  
Author(s):  
Shoaib Ahmed ◽  
Prashant Singh ◽  
Srinath V. Ekkad
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Liquid Crystal ◽  
Transfer Coefficient ◽  
Three Dimensional ◽  
Jet Impingement ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Transfer Coefficients ◽  
Conduction Model

Abstract Liquid crystal thermography and infrared thermography techniques are typically employed to measure detailed surface temperatures, where local heat transfer coefficient (HTC) values are calculated by employing suitable conduction models. One such practice, which is very popular and easy to use, is the transient liquid crystal thermography using one-dimensional semi-infinite conduction model. In these experiments, a test surface with low thermal conductivity and low thermal diffusivity (e.g. acrylic) is used where a step-change in coolant air temperature is induced and surface temperature response is recorded. An error minimization routine is then employed to guess heat transfer coefficients of each pixel, where wall temperature evolution is known through an analytical expression. The assumption that heat flow in the solid is essentially in one-dimension, often leads to errors in HTC determination and this error depends on true HTC, wall temperature evolution and HTC gradient. A representative case of array jet impingement under maximum crossflow condition has been considered here. This heat transfer enhancement concept is widely used in gas turbine leading edge and electronics cooling. Jet impingement is a popular cooling technique which results in high convective heat rates and has steep gradients in heat transfer coefficient distribution. In this paper, we have presented a procedure for solution of three-dimensional transient conduction equation using alternating direction implicit method and an error minimization routine to find accurate heat transfer coefficients at relatively lower computational cost. The HTC results obtained using 1D semi-infinite conduction model and 3D conduction model were compared and it was found that the heat transfer coefficient obtained using the 3D model was consistently higher than the conventional 1D model by 3–16%. Significant deviations, as high as 8–20% in local heat transfer at the stagnation points of the jets were observed between h1D and h3D.

Heat Transfer Characteristics of an Inclined Impinging Jet on a Curved Surface in Crossflow

2014 ◽  
Vol 136 (8) ◽  
Author(s):  
X. L. Wang ◽  
H. B. Yan ◽  
T. J. Lu ◽  
S. J. Song ◽  
T. Kim
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Flat Plate ◽  
Local Heat Transfer ◽  
Impinging Jet ◽  
Local Heat ◽  
Curved Surface ◽  
Heat Transfer Characteristics ◽  
Potential Core ◽  
Transfer Characteristics

This study reports on heat transfer characteristics on a curved surface subject to an inclined circular impinging jet whose impinging angle varies from a normal position θ = 0 deg to θ = 45 deg at a fixed jet Reynolds number of Rej = 20,000. Three curved surfaces having a diameter ratio (D/Dj) of 5.0, 10.0, and infinity (i.e., a flat plate) were selected, each positioned systematically inside and outside the potential core of jet flow where Dj is the circular jet diameter. Present results clarify similar and dissimilar local heat transfer characteristics on a target surface due to the convexity. The role of the potential core is identified to cause the transitional response of the stagnation heat transfer to the inclination of the circular jet. The inclination and convexity are demonstrated to thicken the boundary layer, reducing the local heat transfer (second peaks) as opposed to the enhanced local heat transfer on a flat plate resulting from the increased local Reynolds number.

Sign in / Sign up

Export Citation Format

Share Document