Rotating Stall Induced in Vaneless Diffusers of Very Low Specific Speed Centrifugal Blowers

1985 ◽  
Vol 107 (2) ◽  
pp. 514-519 ◽  
Author(s):  
Y. Kinoshita ◽  
Y. Senoo
Keyword(s):  
Flow Analysis ◽  
Rotating Stall ◽  
Experimental Results ◽  
Flow Coefficient ◽  
Critical Flow ◽  
Flow Rates ◽  
Small Flow ◽  
Low Specific Speed ◽  
Specific Speed ◽  
Vaneless Diffusers

The limit of rotating stall was experimentally determined for three very small specific speed centrifugal blowers. The impellers were specially designed for stall-free at very small flow rates, so that the cause of rotating stall could be attributed to the vaneless diffusers. Experimental results demonstrated that the blowers did not stall until the flow coefficient was reduced to very small values, which had never been reported in the literature. The critical flow coefficient for rotating stall agreed very well with the prediction based on a flow analysis and a criterion for rotating stall in vaneless diffusers developed by the authors.

Part Load Instability and Rotating Stall in a Multistage Low Specific Speed Pump

2020 ◽  
Author(s):  
E. M. A. Vermunt ◽  
K. A. J. Bruurs ◽  
M. S. van der Schoot ◽  
B. P. M. van Esch
Keyword(s):  
Flow Rate ◽  
Head Loss ◽  
Rotating Stall ◽  
Critical Flow ◽  
Flow Rates ◽  
Critical Flow Rate ◽  
Lower Flow ◽  
Low Specific Speed ◽  
Saddle Type ◽  
Specific Speed

Abstract A new diffuser design is developed for a low specific speed, multistage pump. In this design the diffuser and the de-swirl vanes are integrated into single vanes. This creates diffuser channels that extend from behind the impeller exit through the cross-over, up to the eye of the next stage impeller. Experiments show the occurrence of a saddle type instability in the head curve. At a critical flow rate of close to 50% of the flow rate at Best Efficiency Point (BEP), the head drops by 7% of the head at BEP. In this study Computational Fluid Dynamics (CFD) are used in an effort to understand the underlying flow phenomena. The head curve that is obtained with the transient CFD simulations contains a saddle type instability at a flow rate that is approximately the same as in the experiments, but with a lower magnitude. At flow rates higher than the critical flow rate, the predicted head and power are in very good agreement with the experimental data. At flow rates lower than the critical flow rate, the head and power are slightly over-predicted. An analysis of the pressure distribution in the pump reveals that the head loss at different flow rates in the diffuser shows a discontinuity at the critical flow rate. Since both the impeller head and the head loss in the vaneless gap increase continuously for decreasing flow rate, this is an indication that the cause of the head instability lies in the diffuser. Moreover, a strong increase in the variability of head and power at flow rates below the critical flow suggests that the phenomenon is unsteady. Flow patterns in the impeller and in the diffuser, as calculated by CFD, show a high degree of periodicity and are very similar for flow rates down to the critical flow rate. However, for lower flow rates the flow pattern changes completely. A single rotating stall cell is observed that causes two or three neighboring diffuser channels to stall, leading to a significantly lower flow rate or even a reversed flow. This stall pattern rotates in the direction of impeller rotation at a very low frequency of approximately 3.3% of the impeller rotation frequency.

Optimization of Inlet Ring Groove Arrangement for Suppression of Unstable Flow in a Centrifugal Impeller

2005 ◽  
Author(s):  
Masahiro Ishida ◽  
Daisaku Sakaguchi ◽  
Hironobu Ueki
Keyword(s):  
Flow Rate ◽  
The Other ◽  
Centrifugal Impeller ◽  
Shape Parameters ◽  
Unstable Flow ◽  
Ring Groove ◽  
Flow Rates ◽  
Small Flow ◽  
Specific Speed ◽  
Large Flow

An optimization of the inlet ring groove arrangement has been pursued in the present study for obtaining better impeller characteristics and a wider operation range at both small and large flow rates in a high specific speed type centrifugal impeller with inducer. The effects of the shape parameters with respect to the inlet ring groove on the impeller characteristic and the flow incidence were analyzed mainly based on numerical simulations, but also compared to the experimental results. At small flow rates, a significant improvement in the impeller characteristic is achieved due to reduction in the excessive-positive flow incidence by optimizing both location and width of the rear groove near the inducer tip throat. On the other hand, the impeller characteristic is improved at large flow rates by implementing the corner radius at the rear groove edge and by placing another front ring groove in the suction pipe. As a result, by the optimized configuration of the front and rear ring grooves, the unstable flow range of the test impeller can be reduced by about 50% without deterioration of the impeller characteristic even at the 125% flow rate.

Study on Electromagnetic Vibration Pump

2013 ◽  
Vol 774-776 ◽  
pp. 312-315
Author(s):  
Zhan Xiong Lu
Keyword(s):  
Research Field ◽  
Pump Design ◽  
Positive Displacement ◽  
Low Viscosity ◽  
Electromagnetic Vibration ◽  
Displacement Pump ◽  
Small Flow ◽  
Working Principle ◽  
Low Specific Speed ◽  
Specific Speed

Electromagnetic vibration pump is one type of first proposed new household positive displacement pump.It is mainly used to transport water and other low viscosity liquid. It has many advantages including small flow, high head, simple structure,good self-priming performance. Electromagnetic driving method was combined with displacement pump in vibration pump for the first time. Its specific speed can reach below 10,and this is a breakthrough in super-low specific speed pump design. The working principle of electromagnetic vibration pump and its performance were studied in the paper. each of these problems is further discussed and explained in order to point out the research field for the development of electromagnetic vibration pump later.

Effects of short blades on performance and inner flow characteristics of a low-specific-speed centrifugal pump

2017 ◽  
Vol 231 (4) ◽  
pp. 290-302 ◽  
Author(s):  
Can Kang ◽  
Ning Mao ◽  
Chen Pan ◽  
Yang Zhu ◽  
Bing Li
Keyword(s):  
Centrifugal Pump ◽  
Flow Rate ◽  
Pressure Fluctuations ◽  
Flow Characteristics ◽  
Low Flow ◽  
Back Surface ◽  
Flow Rates ◽  
Pump Operation ◽  
Low Specific Speed ◽  
Specific Speed

A low-specific-speed centrifugal pump equipped with long and short blades is studied. Emphasis is placed on the pump performance and inner flow characteristics at low flow rates. Each short blade is intentionally shifted towards the back surface of the neighboring long blade, and the outlet parts of the short blades are uniformly shortened. Unsteady numerical simulation is conducted to disclose inner flow patterns associated with the modified design. Thereby, a comparison is enabled between the two schemes featured by different short blades. Both practical operation data and numerical results support that the deviation and cutting of the short blades can eliminate the positive slope of pump head curve at low flow rates. Therefore, the modification of short blades improves the pump operation stability. Due to the shortening of the outlet parts of the short blades, velocity distributions between impeller outlet and radial diffuser inlet exhibit explicitly altered circumferential flow periodicity. Pressure fluctuations in the radial diffuser are complex in terms of diversified periodicity and amplitudes. Flow rate influences pressure fluctuations in the radial diffuser considerably. As flow rate decreases, the regularity of the orbit of hydraulic loads exerted upon the impeller collapses while hydraulic loads exerted upon the short blades remain circumferentially periodic.

Part Load Instability and Rotating Stall in a Multistage Low Specific Speed Pump

2021 ◽  
Author(s):  
Erik Vermunt ◽  
Martijn Van Der Schoot ◽  
Bruurs Bruurs ◽  
Bart Van Esch
Keyword(s):  
Rotating Stall ◽  
Part Load ◽  
Low Specific Speed ◽  
Specific Speed

scholarly journals Pressure fluctuation–vortex interaction in an ultra-low specific-speed centrifugal pump

2018 ◽  
Vol 38 (2) ◽  
pp. 527-543 ◽  
Author(s):  
Cong Wang ◽  
Yongxue Zhang ◽  
Zhiwei Li ◽  
Ao Xu ◽  
Chang Xu ◽  
...  
Keyword(s):  
Centrifugal Pump ◽  
Pressure Fluctuation ◽  
Leading Edge ◽  
Experimental Results ◽  
Vortex Interaction ◽  
Trailing Edge ◽  
Pressure Surface ◽  
Baroclinic Torque ◽  
Low Specific Speed ◽  
Specific Speed

To provide a comprehensive understanding of the pressure fluctuation–vortex interaction in non-cavitation and cavitation flow, in this article, the unsteady flow in an ultra-low specific-speed centrifugal pump was investigated by numerical simulation. The uncertainty of the numerical framework with three sets of successively refined mesh was verified and validated by a level of 1% of the experimental results. Then, the unsteady results indicate that the features of the internal flow and the pressure fluctuation were accurately captured in accordance with the closed-loop experimental results. The detailed pressure fluctuation at 16 monitoring points and the monitoring of the vorticity suggest that some inconsistent transient phenomena in frequency spectrums show strong correlation with the evolution of vortex, such as abnormal increasing amplitudes at the monitoring points near to the leading edge on the suction surface and the trailing edge on the pressure surface in the case of lower pressurization capacity of impeller after cavitation. Further analysis applies the relative vortex transport equation to intuitionally illustrate the pressure fluctuation–vortex interaction by the contribution of baroclinic torque, viscous diffusion and vortex convection terms. It reveals that the effect of viscous diffusion is weak when the Reynolds number is much greater than 1. Pressure fluctuation amplitude enlarges on the suction side of blade near to the leading edge due to the baroclinic torque in cavitation regions, whereas the abnormal increase of pressure fluctuation after cavitation on the pressure surface of blade approaching the trailing edge results from the vortex convection during vortices moving downstream with the decrease of available net positive suction head at the same instance.

Experimental Investigation of Rotating Stall Characteristics in a Radial Vaneless Diffuser

2000 ◽  
Author(s):  
K. B. Abidogun ◽  
S. A. Ahmed
Keyword(s):  
Flow Instability ◽  
Cell Structure ◽  
Rotating Stall ◽  
Flow Coefficient ◽  
Critical Flow ◽  
Vaneless Diffuser ◽  
Pressure Transducers ◽  
Mass Flowrate ◽  
Hot Wires ◽  
Good Agreement

Rotating stall characteristics in a radial vaneless diffuser model was investigated experimentally. Measurements were made using hot-wires and pressure transducers (static and dynamic). The mass flowrate through the blower, at constant impeller speed, was gradually reduced until flow instability occurred in the diffuser. This enabled the onset and propagation of rotating stall to be fully described. The blower was operated without the vaneless diffuser in order to ascertain the cause of the flow instability. It was discovered that the impeller did not stall at the flow rates at which the blower was operated with the diffuser. The critical flow angles measured at the diffuser inlet, and midway between the diffuser walls, were in good agreement with earlier reported values in the open literature. The maximum number of rotating stall cells found in this study was two. The single-stall cell structure was found to be dominant over the two-stall cell structure at flow coefficients much lower than the critical flow coefficient.

2432 Internal Flow Analysis of Low Specific Speed Centrifugal Pump with Circular Casing

2006 ◽  
Vol 2006.2 (0) ◽  
pp. 183-184
Author(s):  
Jun MATSUI ◽  
Junichi KUROKAWA ◽  
Kouichi NISHINO ◽  
Young-Do Choi ◽  
Kouichi MOURI
Keyword(s):  
Centrifugal Pump ◽  
Flow Analysis ◽  
Internal Flow ◽  
Low Specific Speed ◽  
Specific Speed
Sign in / Sign up

Export Citation Format

Share Document