Stress-Intensity Factors for Internal and External Surface Cracks in Cylindrical Vessels

1982 ◽  
Vol 104 (4) ◽  
pp. 293-298 ◽  
Author(s):  
I. S. Raju ◽  
J. C. Newman
Keyword(s):  
Stress Intensity Factor ◽  
Finite Element ◽  
Stress Intensity ◽  
Intensity Factor ◽  
Internal Pressure ◽  
Stress Intensity Factors ◽  
Crack Depth ◽  
Surface Cracks ◽  
Stress Distributions ◽  
Intensity Factors

The purpose of this paper is to present stress-intensity factor influence coefficients for a wide range of semi-elliptical surface cracks on the inside or outside of a cylinder. The crack surfaces were subjected to four stress distributions: uniform, linear, quadratic, and cubic. These four solutions can be superimposed to obtain stress-intensity factor solutions for other stress distributions, such as those caused by internal pressure and by thermal shock. The results for internal pressure are given herein. The ratio of crack depth to crack length from 0.2 to 1; the ratio of crack depth to wall thickness ranged from 0.2 to 0.8; and the ratio of wall thickness to vessel radius was 0.1 or 0.25. The stress-intensity factors were calculated by a three-dimensional finite-element method. The finite-element models employ singularity elements along the crack front and linear-strain elements elsewhere. The models had about 6500 degrees of freedom. The stress-intensity factors were evaluated from a nodal-force method. The present results were also compared to other analyses of surface cracks in cylinders. The results from a boundary-integral equation method agreed well (±2 percent), and those from other finite-element methods agreed fairly well (±10 percent) with the present results.

Stress Intensity Factors for Circular-Arc Cracks in Plates

2018 ◽  
Author(s):  
D. J. Shim ◽  
S. Tang ◽  
T. J. Kim ◽  
N. S. Huh
Keyword(s):  
Stress Intensity Factor ◽  
Stress Intensity ◽  
Intensity Factor ◽  
Stress Intensity Factors ◽  
Crack Model ◽  
Surface Cracks ◽  
Intensity Factors ◽  
Element Analysis ◽  
Crack Face ◽  
Circular Arc

Stress intensity factor solutions are readily available for flaws found in pipe to pipe welds or shell to shell welds (i.e., circumferential/axial crack in cylinder). In some situations, flaws can be detected in locations where an appropriate crack model is not readily available. For instance, there are no practical stress intensity factor solutions for circular-arc cracks which can form in circular welds (e.g., nozzle to vessel shell welds and storage cask closure welds). In this paper, stress intensity factors for circular-arc cracks in finite plates were calculated using finite element analysis. As a first step, stress intensity factors for circular-arc through-wall crack under uniform tension and crack face pressure were calculated. These results were compared with the analytical solutions which showed reasonable agreement. Then, stress intensity factors were calculated for circular-arc semi-elliptical surface cracks under the lateral and crack face pressure loading conditions. Lastly, to investigate the applicability of straight crack solutions for circular-arc cracks, stress intensity factors for circular-arc and straight cracks (both through-wall and surface cracks) were compared.

Propose of Simplified Stress Intensity Factor Equation for SCC Extension of the Pipe Welds

2008 ◽  
Author(s):  
Mayumi Ochi ◽  
Kiminobu Hojo ◽  
Itaru Muroya ◽  
Kazuo Ogawa
Keyword(s):  
Stress Intensity Factor ◽  
Stress Intensity ◽  
Intensity Factor ◽  
Stress Intensity Factors ◽  
Crack Extension ◽  
Crack Depth ◽  
Alloy 600 ◽  
Intensity Factors ◽  
Axial Crack ◽  
Extension Analysis

Alloy 600 weld joints have potential for primary water stress corrosion cracks (PWSCC). At the present time it has been understood that PWSCC generates and propagates in the Alloy 600 base metal and the Alloy 600 weld metal and there has been no observation of cracking the stainless and the low alloy steel. For the life time evaluation of the pipes or components the crack extension analysis is required. To perform the axial crack extension analysis the stress intensity database or estimation equation corresponding to the extension crack shape is needed. From the PWSCC extension nature mentioned above, stress intensity factors of the conventional handbooks are not suitable because most of them assume a semi-elliptical crack and the maximum aspect ratio crack depth/crack half length is one (The evaluation in this paper had been performed before API 579-1/ASME FFS was published). Normally, with the advance of crack extension in the thickness direction at the weld joint, the crack aspect ratio exceeds one and the K-value of the conventional handbook can not be applied. Even if those equations are applied, the result would be overestimated. In this paper, considering characteristics of PWSCC’s extension behavior in the welding material, the axial crack was modeled in the FE model as a rectangular shape and the stress intensity factors at the deepest point were calculated with change of crack depth. From the database of the stress intensity factors, the simplified equation of stress intensity factor with parameter of radius/thickness and thickness/weld width was proposed.

Effect of Weld Residual Stress Fitting on Stress Intensity Factor for Circumferential Surface Cracks in Pipe

2012 ◽  
Author(s):  
Do-Jun Shim ◽  
Matthew Kerr ◽  
Steven Xu
Keyword(s):  
Residual Stress ◽  
Stress Intensity Factor ◽  
Stress Intensity ◽  
Intensity Factor ◽  
Wall Thickness ◽  
Stress Intensity Factors ◽  
Surface Cracks ◽  
Intensity Factors ◽  
Weld Residual Stress ◽  
Order Polynomial

Recent studies have shown that the crack growth of PWSCC is mainly driven by the weld residual stress (WRS) within the dissimilar metal weld. The existing stress intensity factor (K) solutions for surface cracks in pipe typically require a 4th order polynomial stress distribution through the pipe wall thickness. However, it is not always possible to accurately represent the through thickness WRS with a 4th order polynomial fit and it is necessary to investigate the effect of the WRS fitting on the calculated stress intensity factors. In this paper, two different methods were used to calculate the stress intensity factor for a semi-elliptical circumferential surface crack in a pipe under a given set of simulated WRS. The first method is the Universal Weight Function Method (UWFM) where the through thickness WRS distribution can be represented as a piece-wise cubic fit. In the second method, the through thickness WRS profiles are represented as a 4th order polynomial curve fit (both using the entire wall thickness data and only using data up to the crack-tip). In addition, three-dimensional finite element (FE) analyses (using the simulated weld residual stress) were conducted to serve as a reference solution. The results of this study demonstrate the potential sensitivity of stress intensity factors to 4th order polynomial fitting artifacts. The piece-wise WRS representations used in the UWFM was not sensitive to these fitting artifacts and the UWFM solutions were in good agreement with the FE results.

Finite Element Analysis of Polyethylene Pipe Butt Fusion Joints with Circumferential Surface Cracks

2013 ◽  
Vol 785-786 ◽  
pp. 1151-1158
Author(s):  
Zhi Bin Zhu ◽  
Xiao Xiang Yang ◽  
Li Jing Chen ◽  
Nai Chang Lin ◽  
Zhi Tuo Wang ◽  
...  
Keyword(s):  
Stress Intensity Factor ◽  
Finite Element ◽  
Stress Intensity ◽  
Intensity Factor ◽  
Viscoelastic Material ◽  
Surface Crack ◽  
Crack Depth ◽  
Surface Cracks ◽  
Element Analysis ◽  
Polyethylene Pipe

Based on the viscoelastic material property of polyethylene pipe, software ANSYS was used to simulate and analyze the mechanical property of polyethylene pipe butt fusion joints with circumferential surface crack defects. The viscoelastic material creep parameters were characterized as Prony series and 1/4 node singular element was selected for meshing along the boundaries of the crack, then the stress intensity factor of polyethylene pipe butt fusion joints with circumferential surface crack was calculated under the uniform internal pressure. Through the finite element simulation, the result showed that polyethylene pipe were most likely to fracture failure when crack initiated. Thus the viscoelasticity of materials can be ignored when analyzing the stress intensity factor of circumferential surface cracks of polyethylene pipe. the main influencing factor of the circumferential crack defects was the ratio of the crack depth to the thickness of polyethylene pipe.

scholarly journals Calculation of Outer Crack Stress Intensity Factors for Nozzle Junctions in Cylindrical Pressure Vessels Using FCPAS

2021 ◽  
Author(s):  
Murat Bozkurt ◽  
David Nash ◽  
Asraf Uzzaman
Keyword(s):  
Stress Intensity Factor ◽  
Finite Element ◽  
Stress Intensity ◽  
Intensity Factor ◽  
Stress Intensity Factors ◽  
Pressure Vessel ◽  
Pressure Vessels ◽  
Stress System ◽  
Parameter Study ◽  
Intensity Factors

Abstract Pressure vessels can be subjected to various external local forces and moments acting in combination with main internal pressure. As a result of the stress system set up, and in the presence of attachment welds, surface cracks can occur on the interior and exterior walls. If these cracks cannot be detected at an early stage, there is a real potential for the vessel to rupture with obvious dangerous consequences. The behavior of fractured or geometric discontinuity structures can be investigated with linear elastic fracture mechanics (LEFM) parameters. The stress intensity factor (SIF) is the leading one, and with correct calculations, it can produce the stress intensity in the crack tip region. In cylinder-cylinder intersections subject to local loads, the maximum stress distribution occurs in and around these opening areas and failure in the system usually occurs in this region. Using this approach, the present study develops three-dimensional mixed mode stress intensity factor solutions on for external cracks on nozzle joints in cylindrical pressure vessels nozzle junctions for a variety of geometrical configurations. This was undertaken using a finite element approach and employing a bespoke software tool and solver, FCPAS - Fracture and Crack Propagation Analysis System — to create the finite element mesh and propagation characteristics. From this, a parameter study examining the influence of the crack shape, size and position was carried out with a fixed pressure vessel nozzle cylinder intersection geometry configuration and the appropriate stress intensity factors identified and reported. The FCPAS tool is shown to be an effective approach to modelling and characterizing cracks in pressure vessel nozzles.

Stress Intensity Factors for Complex-Cracked Pipes Based on Elastic Finite Element Analyses

2015 ◽  
Author(s):  
Jae-Uk Jeong ◽  
Jae-Boong Choi ◽  
Nam-Su Huh ◽  
Yun-Jae Kim
Keyword(s):  
Stress Intensity Factor ◽  
Finite Element ◽  
Stress Intensity ◽  
Fracture Mechanics ◽  
Intensity Factor ◽  
Stress Intensity Factors ◽  
Intensity Factors ◽  
Integrity Assessment ◽  
Complex Crack ◽  
Leak Before Break

A complex crack is one of severe crack that can occur at the dissimilar metal weld of nuclear piping. A relevant fracture mechanics assessment for a pipe with a complex crack has become interested in structural integrity of nuclear piping. A stress intensity factor is not only an important parameter in the linear elastic fracture mechanics to predict the stress state at the crack tip, but also one of variables to calculate the J-integral in the elastic plastic fracture mechanics. The accurate calculation of stress intensity factor is required for integrity assessment of nuclear piping system based on Leak-Before-Break concept. In the present paper, stress intensity factors of complex-cracked pipes were calculated by using detailed 3-dimensional finite element analysis. As loading conditions, global bending, axial tension and internal pressure were considered. Based on the present FE works, the values of shape factors for stress intensity factor of complex-cracked pipes are suggested according to a variables change of complex crack geometries and pipes size. Furthermore, the closed-form expressions based on correction factor are newly suggested as a function of geometric variables. These new solutions can be used to Leak-Before-Break evaluation for complex-cracked pipes in the step of elastic J calculation.

scholarly journals Stress-Intensity Factors for Internal Surface Cracks in Cylindrical Pressure Vessels

1980 ◽  
Vol 102 (4) ◽  
pp. 342-346 ◽  
Author(s):  
J. C. Newman ◽  
I. S. Raju
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Stress Intensity ◽  
Wall Thickness ◽  
Stress Intensity Factors ◽  
Crack Depth ◽  
Internal Surface ◽  
Surface Cracks ◽  
Intensity Factors ◽  
Wide Range

The purpose of this paper is to present stress-intensity factors for a wide range of semi-elliptical surface cracks on the inside of pressurized cylinders. The ratio of crack depth to crack length ranged from 0.2 to 1; the ratio of crack depth to wall thickness ranged from 0.2 to 0.8; and the ratio of wall thickness to vessel radius was 0.1 to 0.25. The stress-intensity factors were calculated by a three-dimensional finite-element method. The finite-element models employ singularity elements along the crack front and linear-strain elements elsewhere. The models had about 6500 degrees of freedom. The stress-intensity factors were evaluated from a nodal-force method. An equation for the stress-intensity factors was obtained from the results of the present analysis. The equation applies over a wide range of configuration parameters and was within about 5 percent of the present results. A comparison was also made between the present results and other analyses of internal surface cracks in cylinders. The results from a boundary-integral equation method were in good agreement (± 2 percent) and those from another finite-element method were in fair agreement (± 8 percent) with the present results.

The Singularity of Stress near the Tip of a Crack Perpendicular to an Elastically Mismatched Bimaterial Interface

2014 ◽  
Vol 574 ◽  
pp. 48-52
Author(s):  
Ming Song ◽  
Hao Yong Li ◽  
You Tang Li ◽  
Min Zheng
Keyword(s):  
Stress Intensity Factor ◽  
Finite Element ◽  
Stress Intensity ◽  
Intensity Factor ◽  
Finite Element Methods ◽  
Stress Intensity Factors ◽  
Bimaterial Interface ◽  
Intensity Factors ◽  
Material Combination ◽  
Single Material

This Based on the elastic theory of a crack perpendicular to and terminating at bimaterial interface, a generalized expression of the stress intensity factor is provided for a crack in single material and a crack perpendicular to bimaterial interface, finite element methods are used to calculate the stress intensity factors. The influences of the material combination and crack length on the the stress intensity factors were investigated. Results show that when the crack terminates at bimaterial interface, singular order ofKIis different from that of single material, and the values ofKIincrease with increasingE1/E2andμ1/μ2.

Stress Intensity Factors for Unequal Longitudinal-Radial Cracks in Thick-Walled Cylinders

1991 ◽  
Vol 113 (1) ◽  
pp. 22-27 ◽  
Author(s):  
J. L. Desjardins ◽  
D. J. Burns ◽  
R. Bell ◽  
J. C. Thompson
Keyword(s):  
Stress Intensity Factor ◽  
Finite Element ◽  
Stress Intensity ◽  
Finite Elements ◽  
Intensity Factor ◽  
Stress Intensity Factors ◽  
Two Dimensional ◽  
Intensity Factors ◽  
Radial Cracks ◽  
Good Agreement

Finite elements and two-dimensional photoelasticity have been used to analyze thick-walled cylinders which contain arrays of straight-fronted, longitudinal-radial cracks of unequal depth. The stress intensity factor K1 has been computed for the dominant crack and for some of the surrounding cracks. Cylinders with 2, 4, 6, 8, 16, 36 and 40 cracks have been considered. Good agreement has been obtained between the experimental and the numerical results and, for cylinders with 2 or 4 cracks, with previously published predictions. The results for all of the foregoing cases are used to develop simple, approximate techniques for estimating K1 for the dominant crack, when the total number of cracks is different from those that have been considered herein. Estimates of K1 obtained by these techniques agree well with corresponding finite element results.

Stress intensity factors for semi-elliptical internal surface cracks in autofrettaged thick-walled cylinders

1997 ◽  
Vol 32 (5) ◽  
pp. 351-363 ◽  
Author(s):  
X B Lin ◽  
R A Smith
Keyword(s):  
Stress Intensity Factor ◽  
Fatigue Life ◽  
Stress Intensity ◽  
Intensity Factor ◽  
Stress Intensity Factors ◽  
Inner Core ◽  
Yield Criterion ◽  
Interface Element ◽  
Surface Cracks ◽  
Intensity Factors

Stress intensity factors for internal semi-elliptical surface cracks in autofrettaged cylinders with and without internal pressures applied are presented. The three-dimensional finite element based displacement method with the crack tip square-root singularity of stresses and strains simulated is used to evaluate the stress intensity factors along the crack front. Both allowing and disallowing the overlapping of crack faces are considered in this investigation, the latter being simulated by considering crack surface contact through a kind of interface element introduced into the cracked area. The residual stress distribution assumed to act on the crack face is obtained according to Tresca's yield criterion with the material assumed to be elastic-perfectly plastic. Three different overstrains of autofrettage are chosen. The results show that the stress intensity factor is generally underestimated if the crack contact that has actually occurred is ignored, which may lead to a danger in the assessment of either fracture strength or fatigue life. Implications of the stress intensity factor results are also briefly discussed, particularly for the prediction of fatigue lives, and it is shown that the full autofrettage treatment might be the most beneficial for increasing the fatigue life of cracks initiated from the inner core.

Sign in / Sign up

Export Citation Format

Share Document