A New Approach to the Experimental Study of Turbomachinery Flow Phenomena

1977 ◽  
Vol 99 (1) ◽  
pp. 97-105 ◽  
Author(s):  
J. P. Gostelow
Keyword(s):  
Flow Field ◽  
Unsteady Flow ◽  
Axial Flow ◽  
Centrifugal Pumps ◽  
New Approach ◽  
Static Pressure Distribution ◽  
Compressor Rotor ◽  
Flow Phenomena ◽  
On Line ◽  
Flow Compressor

Measurements of the unsteady flow field over a rotor and within its wake are needed in the development of most turbomachines. The technique advocated is that of data acquisition by on-line computer, using the periodic passing of a blade as a phase reference. The phase-lock averaging process is described as is its use in reducing the noise of raw data traces. Measurements of the unsteady flow over a cascade and of the resulting boundary layer behavior are presented. The approach was used in interpreting the unsteady flow field of an axial-flow compressor rotor and the static pressure distribution over the rotor tip. Finally the application to centrifugal pumps is discussed, enabling the designer to obtain information on the suction pressures and the extent of any separated region.

scholarly journals 3D Flow Field Measurement Around a Rotating Stall Cell

1998 ◽  
Author(s):  
C. Palomba ◽  
P. Puddu ◽  
F. Nurzia
Keyword(s):  
Flow Field ◽  
Axial Flow ◽  
Rotating Stall ◽  
Operating Conditions ◽  
Field Pattern ◽  
Mean Flow ◽  
Axial Section ◽  
Average Technique ◽  
Compressor Rotor ◽  
Flow Compressor

Rotating stall is an unsteady phenomenon that arises in axial and radial flow compressors. Under certain operating conditions a more or less regular cell of turbulent flow develops and propagates around the annulus at a speed lower than rotor speed. Recently little work has been devoted to the understanding of the flow field pattern inside a rotating cell. However, this knowledge could be of help in the understanding of the interaction between the cell and the surrounding flow. Such information could be extremely important during the modelling process when some hypothesis have to be made about the cell behaviour. A detailed experimental investigation has been conducted during one cell operation of an isolated low-speed axial flow compressor rotor using a slanted hot wire and an ensemble average technique based on the cell revolution time. The three flow field components have been measured on 9 axial section for 800 circumferential points and on 21 radial stations to give a complete description of the flow field upstream and downstream of the rotor. Interpretation of data can give a description of the mean flow field patterns inside and around the rotating cell.

scholarly journals Laser Anemometer Measurements in a Transonic Axial Flow Compressor Rotor

1981 ◽  
Vol 103 (2) ◽  
pp. 430-437 ◽  
Author(s):  
A. J. Strazisar ◽  
J. A. Powell
Keyword(s):  
Three Dimensional ◽  
Axial Flow ◽  
Compressor Rotor ◽  
Laser Anemometer ◽  
Flow Phenomena ◽  
Conventional Instrumentation ◽  
Efficient Data ◽  
Shock System ◽  
Flow Compressor ◽  
Anemometer System

A laser anemometer system employing an efficient data acquisition technique has been used to make measurements upstream, within, and downstream of the compressor rotor. A fluorescent dye technique allowed measurements within endwall boundary layers. Adjustable laser beam orientation minimized shadowed regions and enabled radial velocity measurements outside of the blade row. The flow phenomena investigated include flow variations from passage to passage, the rotor shock system, three-dimensional flows in the blade wake, and the development of the outer endwall boundary layer. Laser anemometer measurements are compared to a numerical solution of the streamfunction equations and to measurements made with conventional instrumentation.

Endwall Effects at Two Tip Clearances in a Multistage Axial Flow Compressor With Controlled Diffusion Blading

1994 ◽  
Vol 116 (4) ◽  
pp. 635-645 ◽  
Author(s):  
M. A. Howard ◽  
P. C. Ivey ◽  
J. P. Barton ◽  
K. F. Young
Keyword(s):  
Unsteady Flow ◽  
Axial Flow ◽  
Tip Clearance ◽  
Exit Angle ◽  
Controlled Diffusion ◽  
The Third ◽  
Flow Phenomena ◽  
Multistage Compressor ◽  
Flow Compressor ◽  
Stage Efficiency

Effects of tip clearance, secondary flow, skew, and corner stall on the performance of a multistage compressor with controlled diffusion blading have been studied experimentally. Measurements between 1 and 99 percent annulus height were carried out in both the first and the third stages of a four-stage low-speed compressor with repeating-stage blading. Measurements were obtained at a datum rotor tip clearance and at a more aerodynamically desirable lower clearance. The consequences of the modified rotor tip clearance on both rotor and stator performance are examined in terms of loss coefficient and gas exit angle. Stator losses close to the casing are found to increase significantly when the clearance of an upstream rotor is increased. These increased stator losses cause 30 percent of the stage efficiency reduction that arises with increased rotor tip clearance. The deviation angles due to tip clearance from the multistage measurements are found to be similar to data from single-stage machines with conventional blading, which suggests that the unsteady flow phenomena associated with the multistage environment do not dominate the physics of the flow.

Unsteady flow field under surge and rotating stall in a three-stage axial flow compressor

2011 ◽  
Vol 20 (1) ◽  
pp. 6-12 ◽  
Author(s):  
Takayuki Hara ◽  
Daisuke Morita ◽  
Yutaka Ohta ◽  
Eisuke Outa
Keyword(s):  
Flow Field ◽  
Unsteady Flow ◽  
Axial Flow ◽  
Rotating Stall ◽  
Axial Flow Compressor ◽  
Flow Compressor

J051054 Effects of Tip Leakage Vortex Breakdown on Unsteady Flow Fields in an Axial Flow Compressor Rotor at Near-Stall Condition

2011 ◽  
Vol 2011 (0) ◽  
pp. _J051054-1-_J051054-5
Author(s):  
Hiroaki KIKUTA ◽  
Kazutoyo YAMADA ◽  
Satoshi Gunjishima ◽  
Goki OKADA ◽  
Yasunori HARA ◽  
...  
Keyword(s):  
Unsteady Flow ◽  
Vortex Breakdown ◽  
Axial Flow ◽  
Flow Fields ◽  
Tip Leakage Vortex ◽  
Tip Leakage ◽  
Axial Flow Compressor ◽  
Compressor Rotor ◽  
Flow Compressor

Research on the Unsteady Flow in an Axial Flow Compressor Rotor Based on PVDF Piezoelectric-Film Sensor Array

2017 ◽  
Author(s):  
Jiqing Cong ◽  
Jianping Jing
Keyword(s):  
Unsteady Flow ◽  
Sensor Array ◽  
Pressure Field ◽  
Axial Flow ◽  
Acoustic Resonance ◽  
Piezoelectric Film ◽  
Film Sensor ◽  
Compressor Rotor ◽  
Blade Tip ◽  
Flow Compressor

The unsteady flow in an axial flow compressor rotor is responsible for noise generation and unexpected excitation of blade vibration; therefore, compressors may suffer from fatigue failure of blades and eventually become unable to operate. At present, a set of Kulite pressure transducers mounted on the casing wall is widely used to acquire the pressure field of unsteady flow. However, it will affect the compressor structure and it is physically impossible to mount at a small spacing to capture the variation of casing wall pressure precisely because of the size of transducers. For the requirement of measurement, a self-developed PVDF (polyvinylidene fluoride) piezoelectric-film sensor array measurement system was applied to measure and capture the pressure field distribution over the compressor rotor blade tip clearance. In this system, a multi-measuring points PVDF array, in which 40 measuring points was contained in a 70mm by 40mm rectangle area, was attached on the casing wall of the rotor blade tip. This new technique has great advantages over traditional measurement technique, such as wide frequency response, high space resolution, less impact on the compressor, easy installation and so on. Based on a multistage axial compressor rig test, the unsteady flow pattern on the casing wall was well captured by the PVDF array. And it is revealed in all measuring points that the resonance occurs all over the compressor is under one single frequency, and the pressure level of the acoustic resonance exceeds the level of the usually dominated blade passing frequency when close to the stability limit. At the same time, the acoustic resonance will be modulated with the blade passing frequency.

Large-Scale DES Analysis of Unsteady Flow Field in a Multi-Stage Axial Flow Compressor at Off-Design Condition Using K Computer

2015 ◽  
Author(s):  
Kazutoyo Yamada ◽  
Masato Furukawa ◽  
Satoshi Nakakido ◽  
Akinori Matsuoka ◽  
Kentaro Nakayama
Keyword(s):  
Boundary Condition ◽  
Unsteady Flow ◽  
Gas Turbines ◽  
Large Scale ◽  
Axial Flow ◽  
Axial Flow Compressor ◽  
Eddy Simulation ◽  
Multi Stage ◽  
Flow Phenomena ◽  
Flow Compressor

The paper presents the results of large-scale numerical simulations which were conducted for better understanding of unsteady flow phenomena in a multi-stage axial flow compressor at off-design condition. The compressor is a test rig compressor which was used for development of the industrial gas turbine, Kawasaki L30A. The compressor consists of 14 stages, the front two stages and the front half stages of which were investigated in the present study. The final goal of this study is to elucidate the flow mechanism of the rotating stall inception in the multi-stage axial compressor for actual gas turbines, and according to the test data it is considered that the 2nd stage and the 5th or 6th stage are suspected of leading to the stall. In order to capture precise flow physics in the compressor, a computational mesh for the simulation was generated to have at least several million cells per passage, which amounted to 650 million cells for the front 2-stage simulation and two billion cells for the front 7-stage simulation (about three hundred million cells for each stage). Since these were still not enough for the large-eddy simulation (LES), the detached-eddy simulation (DES) was employed, which can calculate flow fields except near-wall region by LES. The required computational resources were quite large for such simulations, so the computations were conducted on the K computer (RIKEN AICS in Japan). The simulations were well validated, showing good agreement with the measurement results obtained in the test. In the validation, the effect of the boundary condition for the casing wall was also investigated by comparing the results between the adiabatic boundary condition and the isothermal boundary condition. As for the unsteady effect, the wake/blade interaction was investigated in detail. In addition, unsteady flow phenomena in the present compressor at off-design condition were analyzed by using data mining techniques such as vortex identification and limiting streamline drawing with the LIC (line integral convolution) method. The simulation showed that they could be caused by the corner separation on the hub side.

scholarly journals Numerical Prediction of Wakes in Cascades and Compressor Rotors Including the Effects of Mixing: Part II — Rotor Passage Flow and Wakes Including the Effects of Spanwise Mixing

1991 ◽  
Author(s):  
N. Suryavamshi ◽  
B. Lakshminarayana
Keyword(s):  
Flow Field ◽  
Three Dimensional ◽  
Axial Flow ◽  
Radial Component ◽  
Navier Stokes ◽  
Mean Velocity ◽  
Compressor Rotor ◽  
Entire Flow ◽  
High Reynolds ◽  
Flow Compressor

The results of a numerical investigation to predict the flow field including wakes and mixing in axial flow compressor rotors has been presented in this paper. The wake behaviour in a moderately loaded compressor rotor has been studied numerically using a three-dimensional incompressible Navier-Stokes solver with a high Reynolds number form of the k–ε turbulence model. The equations are solved using a time dependent implicit technique. The agreement between the measured data and the predictions are good; including the blade boundary layer profiles, wake mean velocity profiles and decay. The ability of the pseudo-compressibility scheme to predict the entire flow field including the near and far wake profiles and its decay characteristics, effect of loading and the viscous losses of a three-dimensional rotor flow field has been demonstrated. An analysis of the passage averaged velocities and the pressure coefficients shows that the mixing in the downstream regions away from the hub and annulus walls is dominated by wake diffusion. In regions away from the walls, the radial mixing is predominantly caused by the transport of mass, momentum and energy by the radial component of velocity in the wake.

Sign in / Sign up

Export Citation Format

Share Document