Closure to “Discussion of ‘An Augmented, Small-Parameter Equation for the Squeeze-Film Journal Bearing’” (1970, ASME J. Lubr. Technol., 92, pp. 449–450)

1970 ◽  
Vol 92 (3) ◽  
pp. 450-450
Author(s):  
C. L. Strodtman
Keyword(s):  
Small Parameter ◽  
Journal Bearing ◽  
Squeeze Film ◽  
Parameter Equation

An Augmented, Small-Parameter Equation for the Squeeze-Film Journal Bearing

1970 ◽  
Vol 92 (3) ◽  
pp. 442-449 ◽  
Author(s):  
C. L. Strodtman
Keyword(s):  
Small Parameter ◽  
Shape Factor ◽  
Radial Displacement ◽  
Journal Bearing ◽  
Numerical Procedure ◽  
Squeeze Film ◽  
Mean Square ◽  
Root Mean Square Amplitude ◽  
Parameter Equation ◽  
Good Agreement

The asymptotic gas film equation for the squeeze-film journal bearing is solved for the quadratic and cubic terms in the series expansion in terms of the radial displacement. The load support calculated from this augmented, small parameter equation is compared to calculations from an all numerical procedure. Good agreement is shown to exist for large values of the radial displacement. A method of treating nonuniform excursion of the driving member by a root-mean-square amplitude and a shape factor is also given.

Optimization of Clearance in a Squeeze-Film Journal Bearing

1971 ◽  
Vol 93 (2) ◽  
pp. 246-251
Author(s):  
C. L. Strodtman
Keyword(s):  
Numerical Methods ◽  
Small Parameter ◽  
Shape Factor ◽  
Journal Bearing ◽  
Diameter Ratio ◽  
Parameter Analysis ◽  
Squeeze Film ◽  
Clearance Ratio ◽  
Proper Selection ◽  
Selection Of

It is shown that a squeeze-film journal bearing supporting a mass completely contained within the bearing can be designed with the optimum value of minimum clearance by proper selection of the drive amplitude to nominal clearance ratio, the length to diameter ratio, and the shape factor of the excursion. Both a small parameter and an augmented, small parameter analysis are given. In the latter case, numerical methods are employed to solve the resulting equations. The results of the analysis are illustrated in application to an accelerometer design.

Load Support of the Squeeze-Film Journal Bearing of Finite Length

1968 ◽  
Vol 90 (1) ◽  
pp. 157-161 ◽  
Author(s):  
J. V. Beck ◽  
C. L. Strodtman
Keyword(s):  
Finite Difference ◽  
Small Parameter ◽  
Pressure Distribution ◽  
Journal Bearing ◽  
Unit Area ◽  
Parameter Analysis ◽  
Squeeze Film ◽  
Axial Pressure ◽  
Finite Difference Technique ◽  
Additive Term

Despite intuition, the squeeze-film bearing of finite dimensions produces much more load support per unit area than is found from a solution based on an infinite bearing. The load support is shown to be made up of two components—that due to the infinite journal plus an additive term due to the axial pressure distribution. Two methods of solution of the governing equation are applied: (a) A small-parameter analysis and (b) a numerical finite-difference technique. In the limit, the infinitely short journal is shown to have a load support 2.5 times that of the infinitely long journal.

Numerical investigation of dynamic and hydrodynamic characteristics of the pad in the fluid pivot journal bearing

2021 ◽  
pp. 135065012110330
Author(s):  
Tuyen Vu Nguyen ◽  
Weiguang Li
Keyword(s):  
Computational Models ◽  
Journal Bearing ◽  
Squeeze Film ◽  
Hydrodynamic Characteristics ◽  
Hydrodynamic Properties ◽  
Squeeze Film Damper ◽  
Lubricant Oil ◽  
Oil Flow ◽  
Flow Through ◽  
Bearing System

The dynamic and hydrodynamic properties of the pad in the fluid pivot journal bearing are investigated in this paper. Preload coefficients, recess area, and size gap, which were selected as input parameters to investigate, are important parameters of fluid pivot journal bearing. The pad’s pendulum angle, lubricant oil flow through the gap, and recess pressure which characterizes the squeeze film damper were investigated with different preload coefficients, recess area, and gap sizes. The computational models were established and numerical methods were used to determine the equilibrium position of the shaft-bearing system. Since then, the pendulum angle of the pad, liquid flow, and recess pressure were determined by different eccentricities.

Dynamic Behavior of Pure Squeeze Films in Narrow Porous Bearings

1974 ◽  
Vol 96 (3) ◽  
pp. 361-364 ◽  
Author(s):  
P. R. K. Murti
Keyword(s):  
Dynamic Behavior ◽  
Cyclic Load ◽  
Journal Bearing ◽  
Load Capacity ◽  
Squeeze Film ◽  
Closed Form Expression ◽  
Cyclic Loads ◽  
Eccentricity Ratio ◽  
Form Expression ◽  
Bearing Material

The dynamic behavior of squeeze film in a narrow porous journal bearing under a cyclic load is analyzed. A thin-walled bearing with a nonrotating journal is considered and a closed form expression for the pressure distribution is derived. The locus of the journal center is found by numerical methods and it is established with an example that actual contact between the journal and bearing can be avoided by appropriate design of the bearing. Consequently, it is proved that pure squeeze films have a load capacity only under cyclic loads. The analysis also reveals that the permeability of the bearing material and the wall thickness of the bearing influence significantly the operating eccentricity ratio.

Sign in / Sign up

Export Citation Format

Share Document