Discussion: “Bureau of Mines Progress in Developing Open and Closed-Cycle Coal-Burning Gas Turbine Power Plants” (Smith, J., Strimbeck, D. C., Coates, N. H., and McGee, J. P., 1966, ASME J. Eng. Power, 88, pp. 313–320)

1966 ◽  
Vol 88 (4) ◽  
pp. 320-322
Author(s):  
F. Taygun
Keyword(s):  
Gas Turbine ◽  
Power Plants ◽  
Closed Cycle ◽  
Coal Burning

scholarly journals The Coal-Burning Closed-Cycle Gas Turbine

1961 ◽  
Author(s):  
C. Keller ◽  
W. Gaehler
Keyword(s):  
Gas Turbine ◽  
Solid Fuel ◽  
Power Plants ◽  
Oil And Gas ◽  
Closed Cycle ◽  
Ship Propulsion ◽  
Coal Burning

Since 1956, when the last report on closed-cycle gas-turbine development was presented in the U. S., six solid-fuel-fired plants, rated from 2 to 13.5-mw, have come into operation. Additional oil and gas-fired installations, both for stationary power plants and ship propulsion, have been built and operated or will soon start operation. Unfortunately, none of these are in the U. S.

Operating Experience and Design Features of Closed Cycle Gas Turbine Power Plants

1956 ◽  
Author(s):  
Curt Keller
Keyword(s):  
Gas Turbine ◽  
Power Plants ◽  
Operating Experience ◽  
Progress Report ◽  
Closed Cycle ◽  
Design Features ◽  
The Usa

This paper is the author’s third progress report in the USA on the AK-closed cycle gas turbine.

Closed Cycle Gas Turbines: An ECAS Update — Part 1

1979 ◽  
Author(s):  
H. C. Daudet ◽  
C. A. Kinney
Keyword(s):  
Heat Exchanger ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Power Plants ◽  
System Analysis ◽  
Public Utility ◽  
Department Of Energy ◽  
Closed Cycle ◽  
Study Program ◽  
Study Results

This paper presents a discussion of the significant results of a study program conducted for the Department of Energy to evaluate the potential for closed cycle gas turbines and the associated combustion heater systems for use in coal fired public utility power plants. Two specific problem areas were addressed: (a) the identification and analysis of system concepts which offer high overall plant efficiency consistent with low cost of electricity (COE) from coal-pile-to-bus-bar, and (b) the identification and conceptual design of combustor/heat exchanger concepts compatible for use as the cycle gas primary heater for those plant systems. The study guidelines were based directly upon the ground rules established for the ECAS studies to facilitate comparison of study results. Included is a discussion of a unique computer model approach to accomplish the system analysis and parametric studies performed to evaluate entire closed cycle gas turbine utility power plants with and without Rankine bottoming cycles. Both atmospheric fluidized bed and radiant/convective combustor /heat exchanger systems were addressed. Each incorporated metallic or ceramic heat exchanger technology. The work culminated in conceptual designs of complete coal fired, closed cycle gas turbine power plants. Critical component technology assessment and cost and performance estimates for the plants are also discussed.

Applying Combined Pinch and Exergy Analysis to Closed-Cycle Gas Turbine System Design

1995 ◽  
Vol 117 (1) ◽  
pp. 47-52 ◽  
Author(s):  
V. R. Dhole ◽  
J. P. Zheng
Keyword(s):  
Power Systems ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Power Plants ◽  
Exergy Analysis ◽  
Energy Savings ◽  
Design Guidelines ◽  
Closed Cycle ◽  
Practical Design ◽  
Pinch Technology

Pinch technology has developed into a powerful tool for thermodynamic analysis of chemical processes and associated utilities, resulting in significant energy savings. Conventional pinch analysis identifies the most economical energy consumption in terms of heat loads and provides practical design guidelines to achieve this. However, in analyzing systems involving heat and power, for example, steam and gas turbines, etc., pure heat load analysis is insufficient. Exergy analysis, on the other hand, provides a tool for heat and power analysis, although at times it does not provide clear practical design guidelines. An appropriate combination of pinch and exergy analysis can provide practical methodology for the analysis of heat and power systems. The methodology has been successfully applied to refrigeration systems. This paper introduces the application of a combined pinch and exergy approach to commercial power plants with a demonstration example of a closed-cycle gas turbine (CCGT) system. Efficiency improvement of about 0.82 percent (50.2 to 51.02 percent) can be obtained by application of the new approach. More importantly, the approach can be used as an analysis and screening tool for the various design improvements and is generally applicable to any commercial power generation facility.

Status Report on Closed-Cycle Power Plants in the Federal Republic of Germany

1977 ◽  
Vol 99 (1) ◽  
pp. 37-46 ◽  
Author(s):  
K. Bammert ◽  
G. Groschup
Keyword(s):  
Gas Turbine ◽  
Power Plants ◽  
District Heating ◽  
Status Report ◽  
Federal Republic Of Germany ◽  
Closed Cycle ◽  
Special Items ◽  
Air Turbine ◽  
Residential Quarters ◽  
Oil Gas

In recent years the constructors as well as the users of municipal and industrial power plants have shown a rising interest in the closed-cycle gas turbine. Because of its ability to deliver a large amount of heat without restrictions to the electric power generation, the closed-cycle gas turbine is most favorably qualified for central district heating of large residential quarters. In this paper these aspects of the closed-cycle will be illustrated in the frame of five closed air turbine plants, being in operation in the FRG. The layout of and the operation experience gained with these plants will be discussed. These municipal and industrial power plants are fueled by coal, oil, gas, or even mixtures of these. The special items in the layout of the heaters with respect to the different fuels are shown; the perspectives for further design are discussed.

scholarly journals Performance Analyses and Evaluation of Co2 and N2 as Coolants in a Recuperated Brayton Gas Turbine Cycle for a Generation IV Nuclear Reactor Power Plant

2020 ◽  
Vol 6 (2) ◽  
Author(s):  
Emmanuel O. Osigwe ◽  
Arnold Gad-Briggs ◽  
Theoklis Nikolaidis ◽  
Pericles Pilidis ◽  
Suresh Sampath
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Reactor ◽  
Reactor Power ◽  
Critical Conditions ◽  
Working Fluid ◽  
Closed Cycle ◽  
Gas Turbine Cycle

Abstract As demands for clean and sustainable energy renew interests in nuclear power to meet future energy demands, generation IV nuclear reactors are seen as having the potential to provide the improvements required for nuclear power generation. However, for their benefits to be fully realized, it is important to explore the performance of the reactors when coupled to different configurations of closed-cycle gas turbine power conversion systems. The configurations provide variation in performance due to different working fluids over a range of operating pressures and temperatures. The objective of this paper is to undertake analyses at the design and off-design conditions in combination with a recuperated closed-cycle gas turbine and comparing the influence of carbon dioxide and nitrogen as the working fluid in the cycle. The analysis is demonstrated using an in-house tool, which was developed by the authors. The results show that the choice of working fluid controls the range of cycle operating pressures, temperatures, and overall performance of the power plant due to the thermodynamic and heat properties of the fluids. The performance results favored the nitrogen working fluid over CO2 due to the behavior CO2 below its critical conditions. The analyses intend to aid the development of cycles for generation IV nuclear power plants (NPPs) specifically gas-cooled fast reactors (GFRs) and very high-temperature reactors (VHTRs).

The Efficiency of Closed-Cycle Gas Turbines Controlled by Different Methods and Programs

2020 ◽  
pp. 51-63
Author(s):  
V.D. Molyakov ◽  
B.A. Kunikeev ◽  
N.I. Troitskiy
Keyword(s):  
Gas Turbine ◽  
Heat Exchangers ◽  
Gas Turbines ◽  
Power Plants ◽  
Control Method ◽  
Low Pressure ◽  
Working Fluid ◽  
Closed Cycle ◽  
Efficient Operation ◽  
Pressure Compressor

Closed-cycle gas turbine units can be used as power plants for advanced nuclear power stations, spacecraft, ground, surface and underwater vehicles. The purpose and power capacity of closed gas turbine units (CGTU) determine their specific design schemes, taking into account efficient operation of the units both in the nominal (design) mode and in partial power modes. Control methods of both closed and open gas turbine units depend on the scheme and design of the installation but the former differ from the latter mainly in their ability to change gas pressure at the entrance to the low-pressure compressor. This pressure can be changed by controlling the mass circulating in the CGTU circuit, adding or releasing part of the working fluid from the closed system as well as by internal bypassing of the working fluid. At a constant circulating mass in the single-shaft CGTU, the temperature of the gas before the turbines and the shaft speed can be adjusted depending on the type of load. The rotational speed of the turbine shaft, blocked with the compressor, can be adjusted in specific ways, such as changing the cross sections of the flow of the impellers. At a constant mass of the working fluid, the pressure at the entrance to the low-pressure compressor varies depending on the control program. The efficiency of the CGTU in partial power modes depends on the installation scheme, control method and program. The most economical control method is changing the pressure in the circuit. Extraction of the working fluid into special receivers while maintaining the same temperature in all sections of the unit leads to a proportional decrease in the density of the working fluid in all sections and the preservation of gas-dynamic similarity in the nodes (compressors, turbines and pipelines). Specific heat flux rates, and therefore, temperatures change slightly in heat exchangers. As the density decreases, heat fluxes change, as the heat transfer coefficient decreases more slowly than the density of the working fluid. With a decrease in power, this leads to a slight increase in the degree of regeneration and cooling in the heat exchangers. The underestimation of these phenomena in the calculations can be compensated by the underestimation of the growth of losses in partial power modes.

Bureau of Mines Progress in Developing Open and Closed-Cycle Coal-Burning Gas Turbine Power Plants

1966 ◽  
Vol 88 (4) ◽  
pp. 313-320 ◽  
Author(s):  
J. Smith ◽  
D. C. Strimbeck ◽  
N. H. Coates ◽  
J. P. McGee
Keyword(s):  
Gas Turbine ◽  
Refractory Metal ◽  
Power Plants ◽  
Turbine Blades ◽  
Coal Ash ◽  
Inert Gas ◽  
Working Fluid ◽  
Closed Cycle ◽  
Separation Systems ◽  
Open Cycle

Closed-cycle developments include tests of a turbocompressor with hydrodynamic gas bearings. The working fluid is inert gas, with turbine inlet temperatures to 1600 F. A refractory-metal turbine for tests at 1950 F is described. Open-cycle operations for 1963 hours with turbine blades specially designed to resist erosion by coal ash particles are described. Estimated life of the rotor and stator blading was 20,000 and 5000 hours, respectively. Efforts to increase blade life by reducing the amount of ash entering the turbine through improvements in combustion and ash separation systems are described.

Sign in / Sign up

Export Citation Format

Share Document