Geometric Constraint and Mobility Variation of Two 3SvPSv Metamorphic Parallel Mechanisms

2012 ◽  
Vol 135 (1) ◽  
Author(s):  
Ketao Zhang ◽  
Jian S. Dai ◽  
Yuefa Fang
Keyword(s):  
Phase Change ◽  
Unique Feature ◽  
Kinematic Chain ◽  
Geometric Constraint ◽  
Parallel Mechanisms ◽  
Geometrical Condition ◽  
Revolute Joint ◽  
Underlying Principle ◽  
Source Phase ◽  
Hooke’S Joint

This paper presents a unique feature of geometric constraint of adjacent axes of the variable-axis (vA) joint and analyses the effectiveness in the constructed limb, resulting in variation of mobility configuration of two 3SvPSv metamorphic parallel mechanisms. The underlying principle of the metamorphosis of this vA joint is unravelled by investigating the dependence of the corresponding screw system comprising of line vectors, leading to evolution of the vA joint from the source phase Sv to the variable Hooke’s joint phase Uv and the variable revolute-joint phase Rv. The kinematic chain installed with the vA joint forms a reconfigurable limb and is then used to construct two 3SvPSv metamorphic parallel mechanisms proposed in this paper. The phase change of the vA joints incurs the constraint change of the SvPSv limb and subsequently results in the change of mobility configuration of the metamorphic parallel mechanisms. The paper further addresses the geometrical condition for constructing 3SvPSv metamorphic parallel mechanisms following the constraints delivered by the reconfigurable limbs, leading to the analysis of mobility change of the mechanisms induced by the phase change of the limbs.

scholarly journals Constraint and Mobility Change Analysis of Rubik’s Cube-inspired Reconfigurable Joints and Corresponding Parallel Mechanisms

2020 ◽  
Vol 33 (1) ◽  
Author(s):  
Duanling Li ◽  
Pu Jia ◽  
Jiazhou Li ◽  
Dan Zhang ◽  
Xianwen Kong
Keyword(s):  
Parallel Mechanism ◽  
Unique Feature ◽  
Theoretical Method ◽  
Geometric Constraint ◽  
Parallel Mechanisms ◽  
Change Analysis ◽  
Application Range ◽  
And Topology ◽  
Physical Experiments ◽  
Underlying Principle

Abstract The current research of reconfigurable parallel mechanism mainly focuses on the construction of reconfigurable joints. Compared with the method of changing the mobility by physical locking joints, the geometric constraint has good controllability, and the constructed parallel mechanism has more configurations and wider application range. This paper presents a reconfigurable axis (rA) joint inspired and evolved from Rubik's Cubes, which have a unique feature of geometric and physical constraint of axes of joint. The effectiveness of the rA joint in the construction of the limb is analyzed, resulting in a change in mobility and topology of the parallel mechanism. The rA joint makes the angle among the three axes inside the groove changed arbitrarily. This change in mobility is completed by the case illustrated by a 3(rA)P(rA) reconfigurable parallel mechanism having variable mobility from 1 to 6 and having various special configurations including pure translations, pure rotations. The underlying principle of the metamorphosis of this rA joint is shown by investigating the dependence of the corresponding screw system comprising of line vectors, leading to evolution of the rA joint from two types of spherical joints to three types of variable Hooke joints and one revolute joint. The reconfigurable parallel mechanism alters its topology by rotating or locking the axis of rA joint to turn all limbs into different phases. The prototype of reconfigurable parallel mechanism is manufactured and all configurations are enumerated to verify the validity of the theoretical method by physical experiments.

Compositional Submanifolds of Prismatic–Universal–Prismatic and Skewed Prismatic–Revolute– Prismatic Kinematic Chains and Their Derived Parallel Mechanisms

2018 ◽  
Vol 10 (3) ◽  
Author(s):  
Xinsheng Zhang ◽  
Pablo López-Custodio ◽  
Jian S. Dai
Keyword(s):  
Parallel Mechanism ◽  
Kinematic Chain ◽  
Planar Motion ◽  
Helical Motion ◽  
Parallel Mechanisms ◽  
Motion Group ◽  
Revolute Joint ◽  
Kinematic Chains ◽  
Prismatic Joint ◽  
Joint Axis

The kinematic chains that generate the planar motion group in which the prismatic-joint direction is always perpendicular to the revolute-joint axis have shown their effectiveness in type synthesis and mechanism analysis in parallel mechanisms. This paper extends the standard prismatic–revolute–prismatic (PRP) kinematic chain generating the planar motion group to a relatively generic case, in which one of the prismatic joint-directions is not necessarily perpendicular to the revolute-joint axis, leading to the discovery of a pseudo-helical motion with a variable pitch in a kinematic chain. The displacement of such a PRP chain generates a submanifold of the Schoenflies motion subgroup. This paper investigates for the first time this type of motion that is the variable-pitched pseudo-planar motion described by the above submanifold. Following the extraction of a helical motion from this skewed PRP kinematic chain, this paper investigates the bifurcated motion in a 3-prismatic–universal–prismatic (PUP) parallel mechanism by changing the active geometrical constraint in its configuration space. The method used in this contribution simplifies the analysis of such a parallel mechanism without resorting to an in-depth geometrical analysis and screw theory. Further, a parallel platform which can generate this skewed PRP type of motion is presented. An experimental test setup is based on a three-dimensional (3D) printed prototype of the 3-PUP parallel mechanism to detect the variable-pitched translation of the helical motion.

Geometry and Constraint Based Design of Metamorphic Parallel Mechanisms

2011 ◽  
Author(s):  
Ketao Zhang ◽  
Jian S. Dai ◽  
Yuefa Fang
Keyword(s):  
Phase Change ◽  
Independent Set ◽  
Parallel Mechanisms ◽  
Revolute Joints ◽  
Geometric Conditions ◽  
Underlying Principle ◽  
Limb Structure

This paper presents two general metamorphic kinematic units which employ only revolute joints. The two kinematic units with reconfigurability are mapped from independent set of line vectors with different geometry. The underlying principle of the metamorphosis of this kind of reconfigurable kinematic units is unraveled by investigating the dependency of corresponding screw system comprised with line vectors. Limb structure that can be used for constructing new parallel mechanisms is proposed. Subphases of the limb are enumerated accompanying to the phase change of the embodied metamorphic units and constraints corresponding to each phase are analyzed based on reciprocity of screws. Two metamorphic parallel mechanisms which can change their configuration from fully 6-DOF phase to 3-DOF translational subphase and 3-DOF spherical subphase are proposed according to geometric conditions that must be met by limbs. The mobility changes of the platform induced by phase change of limbs are addressed.

scholarly journals Structural-Parametric Synthesis of the RoboMech Class Parallel Mechanism with Two Sliders

2021 ◽  
Vol 11 (21) ◽  
pp. 9831
Author(s):  
Zhumadil Baigunchekov ◽  
Med Amine Laribi ◽  
Giuseppe Carbone ◽  
Azamat Mustafa ◽  
Bekzat Amanov ◽  
...  
Keyword(s):  
Parallel Mechanism ◽  
Kinematic Chain ◽  
Geometric Parameters ◽  
Least Square ◽  
Geometric Constraint ◽  
Parallel Mechanisms ◽  
Parametric Synthesis ◽  
Input And Output ◽  
The Given ◽  
Cold Stamping

This paper addresses the structural-parametric synthesis and kinematic analysis of the RoboMech class of parallel mechanisms (PM) having two sliders. The proposed methods allow the synthesis of a PM with its structure and geometric parameters of the links to obtain the given laws of motions of the input and output links (sliders). The paper outlines a possible application of the proposed approach to design a PM for a cold stamping technological line. The proposed PM is formed by connecting two sliders (input and output objects) using one passive and one negative closing kinematic chain (CKC). The passive CKC does not impose a geometric constraint on the movements of the sliders and the geometric parameters of its links are varied to satisfy the geometric constraint of the negative CKC. The negative CKC imposes one geometric constraint on the movements of the sliders and its geometric parameters are determined on the basis of the Chebyshev and least-square approximations. Problems of positions and analogues of velocities and accelerations of the considered PM are solved to demonstrate the feasibility and effectiveness of the proposed formulations and case of study.

Control Strategy and Trajectory Planning for Reconfiguration of a vA Based Metamorphic Parallel Manipulator

2013 ◽  
Author(s):  
Evangelos Emmanouil ◽  
Ketao Zhang ◽  
Jian S. Dai
Keyword(s):  
Phase Change ◽  
Trajectory Planning ◽  
Control Strategy ◽  
Parallel Manipulator ◽  
Redundant Actuation ◽  
Planning Algorithm ◽  
Source Phase

Mechanisms with reconfigurability have become a trend in development of multi-functional robots which can adapt to unexpected environments and perform complicated tasks. This paper presents a novel metamorphic parallel manipulator with the ability to change its mobility through the phase change of a variable-axis (vA) joint integrated in each limb. The platform has 6 DOFs in the source phase and can reconfigure its mobility to 5, 4 and 3 resorting to redundant actuation. This leads to reconfigurability and multi-functionality of the parallel manipulator characterized by the mobility configuration variation. A control strategy and a trajectory planning algorithm for reconfiguring the mobility configuration of the manipulator are proposed and simulations are carried out to identify a proper way of reconfiguration.

Jacobian Derivation of 5-DOF 3R2T Parallel Mechanisms

2004 ◽  
Author(s):  
Qinchuan Li ◽  
Xudong Hu ◽  
Zhen Huang
Keyword(s):  
Degrees Of Freedom ◽  
Jacobian Matrix ◽  
Screw Theory ◽  
Kinematic Chain ◽  
Parallel Mechanisms ◽  
Mobility Analysis

This paper presents a method for the Jacobian derivation of 5-DOF 3R2T PMs (parallel mechanisms), where 3R denotes three rotational DOFs (degrees of freedom) and 2T denotes two translational DOFs. First the mobility analysis of such kind of parallel mechanisms is reviewed briefly. The Jacobian matrix of the single limb kinematic chain is obtained via screw theory, which is a 6 × 5 matrix. Then it is shown that the mobility analysis of such kind of PM is important when simplifying the 6 × 5 matrix into a 5 × 5 Jacobian matrix. After obtaining the 5 × 5 Jacobian matrix for each limb, a 5 × 5 Jacobian matrix for the whole mechanism can be established.

Reconfigurable Mechanisms From the Intersection of Surfaces

2016 ◽  
Vol 8 (2) ◽  
Author(s):  
P. C. López-Custodio ◽  
J. M. Rico ◽  
J. J. Cervantes-Sánchez ◽  
G. I. Pérez-Soto
Keyword(s):  
Degrees Of Freedom ◽  
Kinematic Chain ◽  
Mobility Analysis ◽  
Revolute Joint ◽  
Revolute Joints ◽  
Reconfigurable Mechanisms ◽  
Three Degrees Of Freedom

The method of intersection of surfaces generated by kinematic dyads is applied to obtain mechanisms that are able to shift from one mode of motion to another. Then a mobility analysis shows that the singularities of the generated surfaces can be used to obtain mechanisms which can change their number of degrees-of-freedom depending on its configuration. The generator dyads are connected as usually done by a spherical pair. However, in the cases shown in this contribution the three-degrees-of-freedom of the spherical pair are not all necessary to keep the kinematic chain closed and movable, and the spherical pair can be substituted by either a pair of intersecting revolute joints or a single revolute joint. This substitution can be obtained by means of two methods presented in this contribution.

Structural Kinematics of Partially-Parallel Robotic Mechanisms

1987 ◽  
Author(s):  
M. Gaber Mohamed
Keyword(s):  
Carrying Capacity ◽  
Kinematic Chain ◽  
Performance Criteria ◽  
Load Carrying Capacity ◽  
Parallel Mechanisms ◽  
Type Synthesis ◽  
Load Carrying ◽  
Parallel Kinematic ◽  
New Generation ◽  
Robotic Applications

Abstract This paper introduces a new generation of robotic mechanisms. Such mechanisms are intermediate between the familiar serial and the fully-parallel robotic mechanisms. They usually comprise several subassemblies that are serially connected to one another. Each subassembly is basically an over constrained fully parallel kinematic chain. Such mechanisms are called “Partially-Parallel Robotic Mechanisms.” A type synthesis of planar and spatial partially-parallel robotic mechanisms is performed. Several practical designs are then introduced and studied for future robotic applications. Several performance criteria of this type of mechanisms are discussed and compared with those of serial as well as fully-parallel robotic mechanisms. Partially-parallel mechanisms are superior than serial mechanisms in rigidity, strength precision positioning and load carrying capacity. Furthermore, they are relatively less complex and have larger range of motion than fully-parallel mechanisms.

The Manta and the Kanuk: Novel 4-DOF Parallel Mechanisms for Industrial Handling

1999 ◽  
Author(s):  
Luc H. Rolland
Keyword(s):  
Parallel Mechanism ◽  
Kinematic Chain ◽  
Parallel Robot ◽  
Chain Structure ◽  
Parallel Robots ◽  
Parallel Mechanisms ◽  
End Effector ◽  
Low Mass ◽  
Loading And Unloading ◽  
Very High

Abstract Two novel 4-DOF very fast parallel robots were designed. This paper introduces the new parallel mechanism designs which are named the Manta and the Kanuk. In order to reduce manipulator overall costs, the actuator and encoder numbers are minimized to the exact effective degrees-of-freedoms (DOF) which is usually not the case in most parallel robot designs. The robots allow end-effector displacements along the three Cartesian translations and one platform transversal rotation. The two remaining rotations are blocked by the intrinsic mechanical structure including the rotation along the platform normal which is always limited in range. The main advantages are high stiffness through the multiple kinematic chain structure which allow for low mass designs. Moreover, they feature simple mechanical construction. Thus, it shall be possible to achieve very high throughput since high accelerations are feasible. To circumvent the known workspace limitations, the actuators were selected to be prismatic along linear axes. The applications are automated warehouse manipulation, mediatheque manipulation, machine tool tool changers, loading and unloading.

Mobility Analysis of a Novel 3-5R Parallel Mechanism Family

2004 ◽  
Vol 126 (1) ◽  
pp. 79-82 ◽  
Author(s):  
Q. C. Li ◽  
Z. Huang
Keyword(s):  
Parallel Mechanism ◽  
Degrees Of Freedom ◽  
Screw Theory ◽  
Kinematic Chain ◽  
Parallel Mechanisms ◽  
Mobility Analysis

Mobility analysis of a novel 3-5R parallel mechanism family whose limb consists of a 2R and a 3R parallel subchain is performed by the aid of screw theory. A mobility criterion applicable to such 3-leg parallel mechanisms in which each kinematic chain contains five kinematic pairs is proposed. It is shown that under different structural conditions, the 3-5R parallel mechanism can have 3, 4, or 5 DOF (degrees of freedom). The structural conditions that guarantee the full-cycle mobility are analyzed. The analysis and the method presented in this paper will be helpful in using such a 3-5R parallel mechanism family and introduce new insights into the mobility analysis of parallel mechanisms.

Sign in / Sign up

Export Citation Format

Share Document