Computational Fluid Dynamics-Based Numerical Analysis of Acoustic Attenuation and Flow Resistance Characteristics of Perforated Tube Silencers

2013 ◽  
Vol 136 (2) ◽  
Author(s):  
Chen Liu ◽  
Zhenlin Ji
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Pressure Drop ◽  
Time Domain ◽  
Transmission Loss ◽  
Air Flow ◽  
Acoustic Attenuation ◽  
Pressure Drops ◽  
Wave Range ◽  
Perforated Tube

The 3D time-domain computational fluid dynamics (CFD) approach is used to calculate the acoustic attenuation performance of perforated tube silencers without and with flow. For the crossflow perforated tube silencer and straight-through perforated tube silencers, the transmission loss predictions agree well with the experimental measurements available in the literature. Then, the 3D time-domain CFD approach is employed to investigate the effects of flow velocity and temperature on the acoustic attenuation performance of perforated tube silencers. The numerical results demonstrated that the transmission loss is increased at most frequencies for the crossflow perforated tube silencer as the air flow increases, while the air flow has little influence on the acoustic attenuation in the plane wave range and increases the acoustic attenuation at higher frequencies for the straight-through perforated tube silencers. Increasing the air temperature shifts the transmission loss curve to higher frequency and lowers the resonance peaks somewhat. The pressure drops of perforated tube silencers are predicted by performing the 3D steady flow computation using CFD. The pressure drop of the crossflow perforated tube silencer is much higher than those of the straight-through perforated tube silencer at the same flow conditions, and the pressure drop of the straight-through perforated tube silencer increases gradually as the porosity increases.

Numerical Investigation of Dusts Removal from Tramway Surface by Street Vacuum Sweeper

2011 ◽  
Vol 236-238 ◽  
pp. 1619-1622 ◽  
Author(s):  
Bo Fu Wu ◽  
Jin Lai Men ◽  
Jie Chen
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Numerical Model ◽  
Pressure Drop ◽  
Removal Efficiency ◽  
Pressure Drops ◽  
Operational Safety ◽  
Airflow Field ◽  
Computational Fluid Dynamics Cfd ◽  
Cfd Method

In order to enhance the operational safety of tram vehicle and reduce the wear of guide wheels mounted on the vehicle, it is necessary to remove particles such as dusts and silts from tramway surface. The aim of this paper is to evaluate the effectiveness of street vacuum sweeper for sucking up dusts from tramway surface. A numerical model was developed based on dusts removal process. Under different pressure drops across the pickup head of the street vacuum sweeper, the flow field and dusts removal efficiency were analyzed with computational fluid dynamics (CFD) method. The numerical results show that a higher pressure drop can improve the airflow field in the pickup head and results in higher dusts removal efficiency, but higher pressure drop definitely need more energy. Therefore, a balance should be taken into consideration.

scholarly journals Influence of perforation and sound-absorbing material filling on acoustic attenuation performance of three-pass perforated mufflers

2018 ◽  
Vol 10 (1) ◽  
pp. 168781401774801 ◽  
Author(s):  
Hongpu Huang ◽  
Zhenlin Ji ◽  
Zhuoliang Li
Keyword(s):  
Finite Element Method ◽  
Transmission Loss ◽  
The Finite Element Method ◽  
Frequency Range ◽  
Acoustic Attenuation ◽  
Pressure Drops ◽  
Outlet Tube ◽  
Middle Chamber ◽  
Absorbing Material ◽  
Perforated Tube

The finite element method is employed to calculate the transmission loss of three-pass perforated reactive and hybrid mufflers. The effects of perforated tubes and bulkheads on the transmission loss of three-pass reactive mufflers are investigated numerically. Two types of hybrid mufflers are considered, and the effects of sound-absorbing material filling and packed outlet tube on the acoustic attenuation performance of mufflers are analyzed. The perforations of the tubes and bulkheads and sound-absorbing material filling are demonstrated to have significant influence on the acoustic attenuation behaviors of the mufflers. The perforation of the tubes and bulkheads may shift the resonance from the low- to middle-frequency range. The sound-absorbing material filling in the middle chamber improves the acoustic attenuation performance at middle to higher frequencies and provides a relatively flat and broadband acoustic attenuation. It is found that the solid inlet or outlet tube replacing the perforated tube and sound-absorbing material filling in the middle chamber increases the pressure drops, while the rest configurations change the pressure drops slightly.

scholarly journals Computational Fluid Dynamics Simulation of Gas–Solid Hydrodynamics in a Bubbling Fluidized-Bed Reactor: Effects of Air Distributor, Viscous and Drag Models

Processes ◽  
2019 ◽  
Vol 7 (8) ◽  
pp. 524 ◽  
Author(s):  
Khezri ◽  
Ghani ◽  
Masoudi Soltani ◽  
Biak ◽  
RobiahYunus ◽  
...  
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Pressure Drop ◽  
Turbulence Models ◽  
Solid Particles ◽  
Dynamics Simulation ◽  
Actual Process ◽  
Momentum Exchange ◽  
Pressure Drops ◽  
Drag Models

In this work, we employed a computational fluid dynamics (CFD)-based model with a Eulerian multiphase approach to simulate the fluidization hydrodynamics in biomass gasification processes. Air was used as the gasifying/fluidizing agent and entered the gasifier at the bottom which subsequently fluidized the solid particles inside the reactor column. The momentum exchange related to the gas-phase was simulated by considering various viscous models (i.e., laminar and turbulence models of the re-normalisation group (RNG), k-ε and k-ω). The pressure drop gradient obtained by employing each viscous model was plotted for different superficial velocities and compared with the experimental data for validation. The turbulent model of RNG k-Ɛ was found to best represent the actual process. We also studied the effect of air distributor plates with different pore diameters (2, 3 and 5 mm) on the momentum of the fluidizing fluid. The plate with 3-mm pores showed larger turbulent viscosities above the surface. The effects of drag models (Syamlal–O’Brien, Gidaspow and energy minimum multi-scale method (EMMS) on the bed’s pressure drop as well as on the volume fractions of the solid particles were investigated. The Syamlal–O’Brien model was found to forecast bed pressure drops most consistently, with the pressure drops recorded throughout the experimental process. The formation of bubbles and their motion along the gasifier height in the presence of the turbulent flow was seen to follow a different pattern from with the laminar flow.

CFD Applications for Coal/Air Balancing in Power Plants

2003 ◽  
Author(s):  
Sowjanya Vijiapurapu ◽  
Jie Cui ◽  
Sastry Munukutla
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Pressure Drop ◽  
Power Plants ◽  
Air Flow ◽  
New Method ◽  
Industry Practice ◽  
Clean Air ◽  
Computational Fluid Dynamics Cfd ◽  
Cfd Applications

A new method for balancing coal / air flow to individual burners connected to a mill in a pulverized coal fired unit was proposed. A generalized calculation procedure based on this method was developed for sizing the orifices needed for balancing the coal / air flow. Efficient use of commercially available computational fluid dynamics (CFD) software was suggested for the calculation of the pressure drop in pipes with unclear specifications of geometries. The current industry practice is to balance the clean air flow and accept the resulting imbalance in the coal / air flow. By this new method the clean-air flow would be unbalanced in a tailored manner so that balanced coal / air flow would result. In order to implement this new method the power plants would still have to conduct clean air tests only.

scholarly journals Evaluation of Active Heat Sinks Design under Forced Convection—Effect of Geometric and Boundary Parameters

Materials ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2041
Author(s):  
Eva C. Silva ◽  
Álvaro M. Sampaio ◽  
António J. Pontes
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Additive Manufacturing ◽  
Pressure Drop ◽  
Forced Convection ◽  
Thermal Performance ◽  
Heat Sinks ◽  
Trapezoidal Shape ◽  
Computational Fluid Dynamics Simulations ◽  
Dynamics Simulations

This study shows the performance of heat sinks (HS) with different designs under forced convection, varying geometric and boundary parameters, via computational fluid dynamics simulations. Initially, a complete and detailed analysis of the thermal performance of various conventional HS designs was taken. Afterwards, HS designs were modified following some additive manufacturing approaches. The HS performance was compared by measuring their temperatures and pressure drop after 15 s. Smaller diameters/thicknesses and larger fins/pins spacing provided better results. For fins HS, the use of radial fins, with an inverted trapezoidal shape and with larger holes was advantageous. Regarding pins HS, the best option contemplated circular pins in combination with frontal holes in their structure. Additionally, lattice HS, only possible to be produced by additive manufacturing, was also studied. Lower temperatures were obtained with a hexagon unit cell. Lastly, a comparison between the best HS in each category showed a lower thermal resistance for lattice HS. Despite the increase of at least 38% in pressure drop, a consequence of its frontal area, the temperature was 26% and 56% lower when compared to conventional pins and fins HS, respectively, and 9% and 28% lower when compared to the best pins and best fins of this study.

scholarly journals Coupling Computational Fluid Dynamics Simulations and Statistical Moments for Designing Healthy Indoor Spaces

2019 ◽  
Vol 16 (5) ◽  
pp. 800 ◽  
Author(s):  
Shamia Hoque ◽  
Firoza Omar
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Air Flow ◽  
Particle Dispersion ◽  
Statistical Moments ◽  
Dispersion Pattern ◽  
Case Scenario ◽  
Worst Case ◽  
Site Specific ◽  
Indoor Spaces

Cross-contamination between occupants in an indoor space may occur due to transfer of infectious aerosols. Computational fluid dynamics (CFD) provides detailed insight into particle transport in indoor spaces. However, such simulations are site-specific. This study couples CFD with statistical moments and establishes a framework that transitions site-specific results to generating guidelines for designing “healthy” indoor spaces. Eighteen cases were simulated, and three parameters were assessed: inlet/outlet location, air changes per hour, and the presence/absence of desks. Aerosol release due to a simulated “sneeze” in a two-dimensional ventilated space was applied as a test case. Mean, standard deviation, and skewness of the velocity profiles and particle locations gave an overall picture of the spread and movement of the air flow in the domain. A parameter or configuration did not dominate the values, confirming the significance of considering the combined influence of multiple parameters for determining localized air-flow characteristics. Particle clustering occurred more when the inlet was positioned above the outlet. The particle dispersion pattern could be classified into two time zones: “near time”, <60 s, and “far time”, >120 s. Based on dosage, the 18 cases were classified into three groups ranging from worst case scenario to best case scenario.

Construction Ventilation Scheme Optimization of Underground Main Powerhouse Based on CFD

2013 ◽  
Vol 368-370 ◽  
pp. 619-623
Author(s):  
Zhen Liu ◽  
Xiao Ling Wang ◽  
Ai Li Zhang
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Flow Field ◽  
Air Flow ◽  
Scheme Optimization ◽  
Pressure Distributions ◽  
Air Volume ◽  
Computational Fluid Dynamics Cfd ◽  
Traditional Construction ◽  
Ventilation Scheme

For the purpose of avoiding the deficiency of the traditional construction ventilation, the ventilation of the underground main powerhouse is simulated by the computational fluid dynamics (CFD) to optimize ventilation parameters. A 3D unsteady RNG k-ε model is performed for construction ventilation in the underground main powerhouse. The air-flow field and CO diffusion in the main powerhouse are simulated and analyzed. The two construction ventilation schemes are modelled for the main powerhouse. The optimized ventilation scheme is obtained by comparing the air volume and pressure distributions of the different ventilation schemes.

Sign in / Sign up

Export Citation Format

Share Document