Investigation of Combustion Phasing Control Strategy During Reactivity Controlled Compression Ignition (RCCI) Multicylinder Engine Load Transitions

2014 ◽  
Vol 136 (9) ◽  
Author(s):  
Yifeng Wu ◽  
Reed Hanson ◽  
Rolf D. Reitz
Keyword(s):  
Steady State ◽  
Control Strategy ◽  
High Efficiency ◽  
Operating Conditions ◽  
Intake Manifold ◽  
Injection Timing ◽  
Compression Ignition ◽  
Reactivity Controlled Compression Ignition ◽  
Phasing Control ◽  
Intake Manifold Pressure

The dual fuel reactivity controlled compression ignition (RCCI) concept has been successfully demonstrated to be a promising, more controllable, high efficiency, and cleaner combustion mode. A multidimensional computational fluid dynamics (CFD) code coupled with detailed chemistry, KIVA-CHEMKIN, was applied to develop a strategy for phasing control during load transitions. Steady-state operating points at 1500 rev/min were calibrated from 0 to 5 bar brake mean effective pressure (BMEP). The load transitions considered in this study included a load-up and a load-down load change transient between 1 bar and 4 bar BMEP at 1500 rev/min. The experimental results showed that during the load transitions, the diesel injection timing responded in two cycles while around five cycles were needed for the diesel common-rail pressure to reach the target value. However, the intake manifold pressure lagged behind the pedal change for about 50 cycles due to the slower response of the turbocharger. The effect of these transients on RCCI engine combustion phasing was studied. The CFD model was first validated against steady-state experimental data at 1 bar and 4 bar BMEP. Then the model was used to develop strategies for phasing control by changing the direct port fuel injection (PFI) amount during load transitions. Specific engine operating cycles during the load transitions (six cycles for the load-up transition and seven cycles for the load-down transition) were selected based on the change of intake manifold pressure to represent the transition processes. Each cycle was studied separately to find the correct PFI to diesel fuel ratio for the desired CA50 (the crank angle at which 50% of total heat release occurs). The simulation results showed that CA50 was delayed by 7 to 15 deg for the load-up transition and advanced by around 5 deg during the load-down transition if the precalibrated steady-state PFI table was used. By decreasing the PFI ratio by 10% to 15% during the load-up transition and increasing the PFI ratio by around 40% during the load-down transition, the CA50 could be controlled at a reasonable value during transitions. The control strategy can be used for closed-loop control during engine transient operating conditions. Combustion and emission results during load transitions are also discussed.

Investigation of Combustion Phasing Control Strategy During Reactivity Controlled Compression Ignition (RCCI) Multi-Cylinder Engine Load Transitions

2013 ◽  
Author(s):  
Yifeng Wu ◽  
Reed Hanson ◽  
Rolf D. Reitz
Keyword(s):  
Steady State ◽  
Control Strategy ◽  
High Efficiency ◽  
Operating Conditions ◽  
Intake Manifold ◽  
Injection Timing ◽  
Compression Ignition ◽  
Reactivity Controlled Compression Ignition ◽  
Phasing Control ◽  
Intake Manifold Pressure

The dual fuel reactivity controlled compression ignition (RCCI) concept has been successfully demonstrated to be a promising, more controllable, high efficiency and cleaner combustion mode. A multi-dimensional computational fluid dynamics (CFD) code coupled with detailed chemistry, KIVA-CHEMKIN, was applied to develop a strategy for phasing control during load transitions. Steady-state operating points at 1500 rev/min were calibrated from 0 to 5 bar brake mean effective pressure (BMEP). The load transitions considered in this study included a load-up and a load-down load change transient between 1 bar and 4 bar BMEP at 1500 rev/min. The experimental results showed that during the load transitions, the diesel injection timing responded in 2 cycles while around 5 cycles were needed for the diesel common-rail pressure to reach the target value. However, the intake manifold pressure lagged behind the pedal change for about 50 cycles due to the slower response of the turbocharger. The effect of these transients on RCCI engine combustion phasing was studied. The CFD model was first validated against steady-state experimental data at 1 bar and 4 bar BMEP. Then the model was used to develop strategies for phasing control by changing the direct port fuel injection (PFI) amount during load transitions. Specific engine operating cycles during the load transitions (6 cycles for the load-up transition and 7 cycles for the load-down transition) were selected based on the change of intake manifold pressure to represent the transition processes. Each cycle was studied separately to find the correct PFI to diesel fuel ratio for the desired CA50 (the crank angle at which 50 % of total heat release occurs). The simulation results showed that CA50 was delayed by 7 to 15 degrees for the load-up transition and advanced by around 5 degrees during the load-down transition if the pre-calibrated steady-state PFI table was used. By decreasing the PFI ratio by 10 % to 15 % during the load-up transition and increasing the PFI ratio by around 40 % during the load-down transition, the CA50 could be controlled at a reasonable value during transitions. The control strategy can be used for closed-loop control during engine transient operating conditions. Combustion and emission results during load transitions are also discussed.

A Comparison of Low-Load Efficiency Optimization on a Heavy-Duty Engine Operated With Gasoline-Diesel RCCI and CDC

2019 ◽  
Author(s):  
R. C. Willems ◽  
F. P. T. Willems ◽  
N. G. Deen ◽  
L. M. T. Somers
Keyword(s):  
Nitrogen Oxides ◽  
Combustion Regime ◽  
Intake Manifold ◽  
Substantial Contribution ◽  
Diesel Combustion ◽  
Compression Ignition ◽  
Heavy Duty ◽  
Lower Efficiency ◽  
Reactivity Controlled Compression Ignition ◽  
Intake Manifold Pressure

Abstract Upcoming CO2 legislation in Europe is driving heavy-duty vehicle manufacturers to develop highly efficient engines more than ever before. Further improvements to conventional diesel combustion, or adopting the reactivity controlled compression ignition concept are both plausible strategies to comply with mandated targets. This work compares these two combustion regimes by performing an optimization on both using Design of Experiments. The tests are conducted on a heavy-duty, single-cylinder engine fueled with either only diesel, or a combination of diesel and gasoline. Analysis of variance is used to reveal the most influential operating parameters with respect to indicated efficiency. Attention is also directed towards the distribution of fuel energy to quantify individual loss channels. A load-speed combination typical for highway cruising is selected given its substantial contribution to the total fuel consumption of long haul trucks. Experiments show that when the intake manifold pressure is limited to levels that are similar to contemporary turbocharger capabilities, the conventional diesel combustion regime outperforms the dual fuel mode. Yet, the latter displays superior low levels of nitrogen oxides. Suboptimal combustion phasing was identified as main cause for this lower efficiency. By leaving the intake manifold pressure unrestricted, reactivity controlled compression ignition surpasses conventional diesel combustion regarding both the emissions of nitrogen oxides and indicated efficiency.

Investigation of the Effect of Injection and Control Strategies on Combustion Instability in Reactivity-Controlled Compression Ignition Engines

2015 ◽  
Vol 138 (1) ◽  
Author(s):  
David T. Klos ◽  
Sage L. Kokjohn
Keyword(s):  
Direct Injection ◽  
Combustion Instability ◽  
Pressure Rise ◽  
Operating Conditions ◽  
Combustion Stability ◽  
Cfd Modeling ◽  
Surface Model ◽  
Injection Timing ◽  
Compression Ignition ◽  
Reactivity Controlled Compression Ignition

This paper uses detailed computational fluid dynamics (CFD) modeling with the kiva-chemkin code to investigate the influence of injection timing, combustion phasing, and operating conditions on combustion instability. Using detailed CFD simulations, a large design of experiments (DOE) is performed with small perturbations in the intake and fueling conditions. A response surface model (RSM) is then fit to the DOE results to predict cycle-to-cycle combustion instability. Injection timing had significant tradeoffs between engine efficiency, emissions, and combustion instability. Near top dead center (TDC) injection timing can significantly reduce combustion instability, but the emissions and efficiency drop close to conventional diesel combustion levels. The fuel split between the two direct injection (DI) injections has very little effect on combustion instability. Increasing exhaust gas recirculation (EGR) rate, while making adjustments to maintain combustion phasing, can significantly reduce peak pressure rise rate (PPRR) variation until the engine is on the verge of misfiring. Combustion phasing has a very large impact on combustion instability. More advanced phasing is much more stable, but produces high PPRRs, higher NOx levels, and can be less efficient due to increased heat transfer losses. The results of this study identify operating parameters that can significantly improve the combustion stability of dual-fuel reactivity-controlled compression ignition (RCCI) engines.

scholarly journals Effect of Injection Timing and Injection Duration of Manifold Injected Fuels in Reactivity Controlled Compression Ignition Engine Operated with Renewable Fuels

Energies ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4621
Author(s):  
P. A. Harari ◽  
N. R. Banapurmath ◽  
V. S. Yaliwal ◽  
T. M. Yunus Khan ◽  
Irfan Anjum Badruddin ◽  
...  
Keyword(s):  
Nitric Oxide ◽  
Injection Timing ◽  
Compression Ignition ◽  
Cylinder Pressure ◽  
Compression Ignition Engine ◽  
Compressed Natural Gas ◽  
Reactivity Controlled Compression Ignition ◽  
Brake Thermal Efficiency ◽  
Injection Duration ◽  
Fuel Mixtures

In the current work, an effort is made to study the influence of injection timing (IT) and injection duration (ID) of manifold injected fuels (MIF) in the reactivity controlled compression ignition (RCCI) engine. Compressed natural gas (CNG) and compressed biogas (CBG) are used as the MIF along with diesel and blends of Thevetia Peruviana methyl ester (TPME) are used as the direct injected fuels (DIF). The ITs of the MIF that were studied includes 45°ATDC, 50°ATDC, and 55°ATDC. Also, present study includes impact of various IDs of the MIF such as 3, 6, and 9 ms on RCCI mode of combustion. The complete experimental work is conducted at 75% of rated power. The results show that among the different ITs studied, the D+CNG mixture exhibits higher brake thermal efficiency (BTE), about 29.32% is observed at 50° ATDC IT, which is about 1.77, 3.58, 5.56, 7.51, and 8.54% higher than D+CBG, B20+CNG, B20+CBG, B100+CNG, and B100+CBG fuel combinations. The highest BTE, about 30.25%, is found for the D+CNG fuel combination at 6 ms ID, which is about 1.69, 3.48, 5.32%, 7.24, and 9.16% higher as compared with the D+CBG, B20+CNG, B20+CBG, B100+CNG, and B100+CBG fuel combinations. At all ITs and IDs, higher emissions of nitric oxide (NOx) along with lower emissions of smoke, carbon monoxide (CO), and hydrocarbon (HC) are found for D+CNG mixture as related to other fuel mixtures. At all ITs and IDs, D+CNG gives higher In-cylinder pressure (ICP) and heat release rate (HRR) as compared with other fuel combinations.

scholarly journals Octane Index Applicability over the Pressure-Temperature Domain

Energies ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 607
Author(s):  
Tommy R. Powell ◽  
James P. Szybist ◽  
Flavio Dal Forno Chuahy ◽  
Scott J. Curran ◽  
John Mengwasser ◽  
...  
Keyword(s):  
High Efficiency ◽  
National Laboratory ◽  
Operating Conditions ◽  
Dominant Factor ◽  
Compression Ignition ◽  
Oak Ridge ◽  
Operating Modes ◽  
Wide Range ◽  
Thermodynamic Conditions ◽  
Si Engines

Modern boosted spark-ignition (SI) engines and emerging advanced compression ignition (ACI) engines operate under conditions that deviate substantially from the conditions of conventional autoignition metrics, namely the research and motor octane numbers (RON and MON). The octane index (OI) is an emerging autoignition metric based on RON and MON which was developed to better describe fuel knock resistance over a broader range of engine conditions. Prior research at Oak Ridge National Laboratory (ORNL) identified that OI performs reasonably well under stoichiometric boosted conditions, but inconsistencies exist in the ability of OI to predict autoignition behavior under ACI strategies. Instead, the autoignition behavior under ACI operation was found to correlate more closely to fuel composition, suggesting fuel chemistry differences that are insensitive to the conditions of the RON and MON tests may become the dominant factor under these high efficiency operating conditions. This investigation builds on earlier work to study autoignition behavior over six pressure-temperature (PT) trajectories that correspond to a wide range of operating conditions, including boosted SI operation, partial fuel stratification (PFS), and spark-assisted compression ignition (SACI). A total of 12 different fuels were investigated, including the Co-Optima core fuels and five fuels that represent refinery-relevant blending streams. It was found that, for the ACI operating modes investigated here, the low temperature reactions dominate reactivity, similar to boosted SI operating conditions because their PT trajectories lay close to the RON trajectory. Additionally, the OI metric was found to adequately predict autoignition resistance over the PT domain, for the ACI conditions investigated here, and for fuels from different chemical families. This finding is in contrast with the prior study using a different type of ACI operation with different thermodynamic conditions, specifically a significantly higher temperature at the start of compression, illustrating that fuel response depends highly on the ACI strategy being used.

Control Strategy and Realization of Dual Fuel Engine with Intake Premixed Methanol on Turbocharging Diesel Engine

2012 ◽  
Vol 614-615 ◽  
pp. 436-440
Author(s):  
Jia Yi Du ◽  
Hai Ling Li ◽  
Deng Pan Zhang ◽  
Yong Jia Lu
Keyword(s):  
Diesel Engine ◽  
Control Strategy ◽  
Interpolation Method ◽  
Intake Manifold ◽  
Bench Test ◽  
Dual Fuel ◽  
Operation Conditions ◽  
Di Diesel Engine ◽  
Table Data ◽  
Intake Manifold Pressure

Based on Methanol and diesel special combustion mode, a control strategy of methanol/diesel dual fuel engine on turbocharged DI diesel engine was introduced according to different operation conditions. A method of judging engine load by measuring intake manifold pressure was put forward. Bicubic interpolation method was adopted to optimize the control MAP for ensuring the coincidence between look-up table data and actual conditions. The feasibility of the control strategy is verified by bench test. And the results of test show that the economic performance of this dual fuel engine got a considerable improvement.

Parametric Study of Ignition and Combustion Characteristics From a Gasoline Compression Ignition Engine Using Two Different Reactivity Fuels

2016 ◽  
Author(s):  
Khanh Cung ◽  
Toby Rockstroh ◽  
Stephen Ciatti ◽  
William Cannella ◽  
S. Scott Goldsborough
Keyword(s):  
High Speed ◽  
Injection Pressure ◽  
Operating Conditions ◽  
Combustion Stability ◽  
Injection Timing ◽  
Strong Impact ◽  
Boost Pressure ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Ignition And Combustion

Unlike homogeneous charge compression ignition (HCCI) that has the complexity in controlling the start of combustion event, partially premixed combustion (PPC) provides the flexibility of defining the ignition timing and combustion phasing with respect to the time of injection. In PPC, the stratification of the charge can be influenced by a variety of methods such as number of injections (single or multiple injections), injection pressure, injection timing (early to near TDC injection), intake boost pressure, or combination of several factors. The current study investigates the effect of these factors when testing two gasoline-like fuels of different reactivity (defined by Research Octane Number or RON) in a 1.9-L inline 4-cylinder diesel engine. From the collection of engine data, a full factorial analysis was created in order to identify the factors that most influence the outcomes such as the location of ignition, combustion phasing, combustion stability, and emissions. Furthermore, the interaction effect of combinations of two factors or more was discussed with the implication of fuel reactivity under current operating conditions. The analysis was done at both low (1000 RPM) and high speed (2000 RPM). It was found that the boost pressure and air/fuel ratio have strong impact on ignition and combustion phasing. Finally, injection-timing sweeps were conducted whereby the ignition (CA10) of the two fuels with significantly different reactivity were matched by controlling the boost pressure while maintaining a constant lambda (air/fuel equivalence ratio).

Effect of Injection Timing on PPCI and MPCI Mode Fueled With Straight-Run Naphtha

2013 ◽  
Vol 136 (3) ◽  
Author(s):  
Hongqiang Yang ◽  
Shijin Shuai ◽  
Zhi Wang ◽  
Jianxin Wang
Keyword(s):  
Diesel Fuel ◽  
Single Injection ◽  
Operating Conditions ◽  
Premixed Combustion ◽  
Spray Combustion ◽  
Injection Timing ◽  
Soot Emission ◽  
Compression Ignition ◽  
Injection Strategy ◽  
Injection Strategies

Partially premixed compression ignition (PPCI) and multiple premixed compression ignition (MPCI) mode of straight-run naphtha have been investigated under different injection strategies. The MPCI mode is realized by the multiple premixed combustion processes in a sequence of “spray-combustion-spray-combustion” around the compression top dead center. The spray and combustion events are preferred to be completely separated, without any overlap in the temporal sequence in order to ensure the multiple-stage premixed compression ignition. The PPCI mode is well known as the “spray-spray-combustion” sequence, with the start of combustion separated from the end of injection. Straight-run naphtha with a research octane number (RON) of 58.8 is tested in a single cylinder compression ignition engine whose compression ratio is 16.7 and displacement is 0.5 l. Double and triple injection strategies are investigated as the last injection timing sweeping at 1.0 MPa IMEP and 1800 rpm conditions. The MPCI mode is achieved using the double injection strategy, but its soot emission is higher than the PPCI mode under triple injection strategy. This is mainly because of the lower RON of the straight-run naphtha and the ignition delay is too short to form an ideally premixed combustion process after the second injection of straight-run naphtha. Diesel fuel is also tested under the same operating conditions, except for employing a single injection strategy. The naphtha PPCI and MPCI mode both have lower fuel consumption and soot emission than diesel fuel single injection mode, but the THC emissions are both higher than that of diesel fuel.

Effects of EGR and Boost Pressure on Reactivity Controlled Compression Ignition (RCCI) Engine at High Load Operating Conditions

2014 ◽  
Author(s):  
Yifeng Wu ◽  
Rolf D. Reitz
Keyword(s):  
Peak Pressure ◽  
Pressure Rise ◽  
High Load ◽  
Operating Conditions ◽  
Boost Pressure ◽  
Compression Ignition ◽  
Effective Pressure ◽  
Reactivity Controlled Compression Ignition ◽  
Brake Mean Effective Pressure ◽  
Diesel Injection

Reactivity Controlled Compression Ignition (RCCI) at engine high load operating conditions is investigated in this study. The effects of EGR and boost pressure on RCCI combustion were studied by using a multi-dimensional computational fluid dynamics (CFD) code. The model was first compared with a previous CFD model, which has been validated against steady-state experimental data of gasoline-diesel RCCI in a multi-cylinder light duty engine. An RCCI piston with a compression ratio of 15:1 was then proposed to improve the combustion and emissions at high load. The simulation results showed that 18 bar indicated mean effective pressure (IMEP) could be achieved with gasoline-diesel RCCI at an EGR rate of 35 % and equivalence ratio of 0.96, while the peak pressure rise rate (PPRR) and engine combustion efficiency could both be controlled at reasonable levels. Simulations using both early and late direct-injection (DI) of diesel fuel showed that RCCI combustion at high load is very sensitive to variations of the exhaust gas recirculation (EGR) amount. Higher IMEP is obtained by using early diesel injection, and it is less sensitive to EGR variation compared to late diesel injection. Reduced unburned hydrocarbon (HC), carbon monoxide (CO), soot and slightly more nitrogen oxides (NOx) emissions were seen for early diesel injection. HC, CO and soot emissions were found to be more sensitive to EGR variation at late diesel injection timings. However, there was little difference in terms of peak pressure, efficiencies, PPRR and phasing under varying EGR rates. The effect of boost pressure on RCCI at high load operating conditions was also studied at different EGR rates. It was found that combustion and emissions were improved, and the sensitivity of the combustion and emission to EGR was reduced with higher boost pressures. In addition, cases with similar combustion phasing and reasonable PPRR were analyzed by using an experimentally validated GT-Power model. The results indicated that although higher IMEP was generated at higher boost pressures, the brake mean effective pressure (BMEP) was similar compared to that obtained with lower boost pressures due to higher pumping losses.

Sign in / Sign up

Export Citation Format

Share Document