Application of Rigid-Body-Linkage Static Balancing Techniques to Reduce Actuation Effort in Compliant Mechanisms

2015 ◽  
Vol 8 (2) ◽  
Author(s):  
Sangamesh R. Deepak ◽  
Amrith N. Hansoge ◽  
G. K. Ananthasuresh
Keyword(s):  
Rigid Body ◽  
General Framework ◽  
Compliant Mechanisms ◽  
Compliant Mechanism ◽  
Small Length ◽  
Element Analysis ◽  
Static Balancing ◽  
Free Length ◽  
First Order ◽  
Taylor’S Series

There are analytical methods in the literature where a zero-free-length spring-loaded linkage is perfectly statically balanced by addition of more zero-free-length springs. This paper provides a general framework to extend these methods to flexure-based compliant mechanisms through (i) the well know small-length flexure model and (ii) approximation between torsional springs and zero-free-length springs. We use first-order truncated Taylor's series for the approximation between the torsional springs and zero-free-length springs so that the entire framework remains analytical, albeit approximate. Three examples are presented and the effectiveness of the framework is studied by means of finite-element analysis and a prototype. As much as 70% reduction in actuation effort is demonstrated. We also present another application of static balancing of a rigid-body linkage by treating a compliant mechanism as the spring load to a rigid-body linkage.

Using Rigid-Body Mechanism Topologies to Design Shape-Changing Compliant Mechanisms

2015 ◽  
Vol 8 (1) ◽  
Author(s):  
Kai Zhao ◽  
James P. Schmiedeler
Keyword(s):  
Rigid Body ◽  
Shape Matching ◽  
Compliant Mechanisms ◽  
Compliant Mechanism ◽  
Shape Change ◽  
Mesh Network ◽  
Adaptive Antenna ◽  
Optimal Size ◽  
Dimensional Synthesis ◽  
Element Analysis

This paper uses rigid-body mechanism topologies to synthesize fully distributed compliant mechanisms that approximate a shape change defined by a set of morphing curves in different positions. For a shape-change problem, a rigid-body mechanism solution is generated first to provide the base topology. This base topology defines a preselected design space for the structural optimization in one of two ways so as to obtain a compliant mechanism solution that is typically superior to the local minimum solutions obtained from searching more expansive design spaces. In the first strategy, the dimensional synthesis directly determines the optimal size and shape of the distributed compliant mechanism having exactly the base topology. In the second strategy, an initial mesh network established from the base topology is used to generate different topologies (in addition to the base), and an improved design domain parameterization scheme ensures that only topologies with well-connected structures are evaluated. The deformation of each generated compliant mechanism is evaluated using geometrically nonlinear finite element analysis (FEA). A two-objective genetic algorithm (GA) is employed to find a group of viable designs that trade off minimizing shape matching error with minimizing maximum stress. The procedure's utility is demonstrated with three practical examples—the first two approximating open-curve profiles of an adaptive antenna and the third approximating closed-curve profiles of a morphing wing.

Design of a Continuum Mechanism that Matches the Movement of an Eight-bar Linkage

2020 ◽  
pp. 1-11
Author(s):  
Xueao Liu ◽  
J. Michael McCarthy
Keyword(s):  
Finite Element Analysis ◽  
Rigid Body ◽  
Design Methodology ◽  
Compliant Mechanisms ◽  
Compliant Mechanism ◽  
Initial Structure ◽  
Element Analysis ◽  
Kinematic Synthesis ◽  
Generic Structure ◽  
Straight Line

Abstract This paper presents a design methodology for mechanisms consisting of a single continuous structure, continuum mechanisms, that blends the kinematic synthesis of rigid-body mechanisms with topology optimization for compliant mechanisms. Rather than start with a generic structure that is shaped to achieve a required force deflection task for a compliant mechanism, our approach shapes the initial structure based on kinematic synthesis of a rigid body mechanism for the required movement, then the structure is shaped using Finite Element Analysis to achieve the required force deflection relationship. The result of this approach is a continuum mechanism with the same workpiece movement as the rigid link mechanism when actuated. An example illustrates the design process to obtain an eight-bar linkage that guides its workpiece in straight-line rectilinear movement. We show that the resulting continuum mechanism provides the desired rectilinear movement. A 210 mm physical model machined from Nylon-6 is shown to achieve 21.5mm rectilinear movement with no perceived deviation from a straight-line.

scholarly journals Compliant Mechanism Road Bicycle Brake: A Rigid-Body Replacement Case Study

2011 ◽  
Author(s):  
Brian M. Olsen ◽  
Larry L. Howell ◽  
Spencer P. Magleby
Keyword(s):  
Rigid Body ◽  
High Performance ◽  
Compliant Mechanisms ◽  
Compliant Mechanism ◽  
Element Analysis ◽  
Low Weight ◽  
Rigid Body Model ◽  
Compliant Mechanism Design

This paper demonstrates rigid-body replacement synthesis in the design a mechanism with known design objectives. The design of high-performance bicycle brakes is complicated by a variety of competing design objectives, including increased performance and low weight. But this challenge also provides a good case study to demonstrate the design of compliant mechanisms to replace traditional rigid-link mechanisms. This paper briefly reviews current road brake designs, demonstrates the use of rigid-body replacement synthesis to design a compliant mechanism, and illustrates the combination of compliant mechanism design tools. The resulting concept was generated from the modified dual-pivot brake design and is a partially compliant mechanism where one pin has the dual role of a joint and a mounting pin. The pseudo-rigid-body model, finite element analysis, and optimization algorithms are used to generate design dimensions, and designs are considered for both titanium and E-glass flexures. The resulting design has the potential of reducing the part count and overall weight while maintaining a performance similar to the benchmark.

Using Rigid-Body Mechanism Topologies to Design Shape-Changing Compliant Mechanisms

2013 ◽  
Author(s):  
Kai Zhao ◽  
James P. Schmiedeler
Keyword(s):  
Rigid Body ◽  
Compliant Mechanisms ◽  
Compliant Mechanism ◽  
Shape Change ◽  
Adaptive Antenna ◽  
Dimensional Synthesis ◽  
Element Analysis ◽  
Initial Element ◽  
Multi Objective Genetic Algorithm ◽  
Improved Design

This paper uses rigid-body mechanism topologies to synthesize distributed compliant mechanisms that approximate a shape change defined by a set of morphing curves in different positions. A single-actuator compliant mechanism is synthesized from a single degree-of-freedom rigid-body mechanism’s base topology in one of two ways. In one case, the base topology is directly evaluated through dimensional synthesis to determine the compliant mechanism’s optimal dimensions. In the second, the base topology establishes an initial element network for an optimization routine that determines topologies and dimensions simultaneously, and an improved design domain parameterization scheme ensures that only topologies with well-connected structures are evaluated. A multi-objective genetic algorithm is employed to search the design space, and the deformation is evaluated using geometrically nonlinear finite element analysis. The procedure’s utility is demonstrated with two practical examples — one approximating open-curve profiles of an adaptive antenna and the other closed-curve profiles of a morphing wing.

Bistable Compliant Four-Bar Mechanisms With a Single Torsional Spring

2006 ◽  
Author(s):  
Adarsh Mavanthoor ◽  
Ashok Midha
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Mechanism Design ◽  
Compliant Mechanisms ◽  
Compliant Mechanism ◽  
Stored Energy ◽  
Element Analysis ◽  
Bistable Behavior ◽  
Torsional Spring ◽  
Bistable Mechanism

Significant reduction in cost and time of bistable mechanism design can be achieved by understanding their bistable behavior. This paper presents bistable compliant mechanisms whose pseudo-rigid-body models (PRBM) are four-bar mechanisms with a torsional spring. Stable and unstable equilibrium positions are calculated for such four-bar mechanisms, defining their bistable behavior for all possible permutations of torsional spring locations. Finite Element Analysis (FEA) and simulation is used to illustrate the bistable behavior of a compliant mechanism with a straight compliant member, using stored energy plots. These results, along with the four-bar and the compliant mechanism information, can then be used to design a bistable compliant mechanism to meet specified requirements.

A Simple and Accurate Method for Determining Large Deflections in Compliant Mechanisms Subjected to End Forces and Moments

1998 ◽  
Vol 120 (3) ◽  
pp. 392-400 ◽  
Author(s):  
A. Saxena ◽  
S. N. Kramer
Keyword(s):  
Rigid Body ◽  
Compliant Mechanisms ◽  
Compliant Mechanism ◽  
Elliptic Integral ◽  
Beam Equation ◽  
Large Deflections ◽  
Euler Beam ◽  
Body Model ◽  
Rigid Body Model ◽  
Analysis And Synthesis

Compliant members in flexible link mechanisms undergo large deflections when subjected to external loads. Because of this fact, traditional methods of deflection analysis do not apply. Since the nonlinearities introduced by these large deflections make the system comprising such members difficult to solve, parametric deflection approximations are deemed helpful in the analysis and synthesis of compliant mechanisms. This is accomplished by representing the compliant mechanism as a pseudo-rigid-body model. A wealth of analysis and synthesis techniques available for rigid-body mechanisms thus become amenable to the design of compliant mechanisms. In this paper, a pseudo-rigid-body model is developed and solved for the tip deflection of flexible beams for combined end loads. A numerical integration technique using quadrature formulae has been employed to solve the large deflection Bernoulli-Euler beam equation for the tip deflection. Implementation of this scheme is simpler than the elliptic integral formulation and provides very accurate results. An example for the synthesis of a compliant mechanism using the proposed model is also presented.

A Simple and Accurate Method for Determining Large Deflections in Complaint Mechanisms Subjected to End Forces and Moments

1998 ◽  
Author(s):  
A. Saxena ◽  
Steven N. Kramer
Keyword(s):  
Rigid Body ◽  
Numerical Integration ◽  
Compliant Mechanisms ◽  
Compliant Mechanism ◽  
Beam Equation ◽  
Integration Scheme ◽  
Large Deflections ◽  
Body Model ◽  
Rigid Body Model ◽  
Analysis And Synthesis

Abstract Compliant members in flexible link mechanisms undergo large deflections when subjected to external loads for which, traditional methods of deflection analysis do not apply Nonlinearities introduced by these large deflections make the system comprising such members difficult to solve Parametric deflection approximations are then deemed helpful in the analysis and synthesis of compliant mechanisms This is accomplished by seeking the pseudo-rigid-body model representation of the compliant mechanism A wealth of analysis and synthesis techniques available for rigid-body mechanisms thus become amenable to the design of compliant mechanisms In this paper, a pseudo-rigid-body model is developed and solved for the tip deflection of flexible beams for combined end loads with positive end moments A numerical integration technique using quadrature formulae has been employed to solve the nonlinear Bernoulli-Euler beam equation for the tip deflection Implementation of this scheme is relatively simpler than the elliptic integral formulation and provides nearly accurate results Results of the numerical integration scheme are compared with the beam finite element analysis An example for the synthesis of a compliant mechanism using the proposed model is also presented.

Evaluation of Equivalent Spring Stiffness for Use in a Pseudo-Rigid-Body Model of Large-Deflection Compliant Mechanisms

1994 ◽  
Author(s):  
Larry L. Howell ◽  
Ashok Midha
Keyword(s):  
Rigid Body ◽  
Large Deflection ◽  
Compliant Mechanisms ◽  
Compliant Mechanism ◽  
Spring Stiffness ◽  
Model Concept ◽  
Analysis And Design ◽  
Body Model ◽  
Rigid Body Model ◽  
Body Joints

Abstract Compliant mechanisms gain some or all of their mobility from the flexibility of their members rather than from rigid-body joints only. More efficient and usable analysis and design techniques are needed before the advantages of compliant mechanisms can be fully utilized. In an earlier work, a pseudo-rigid-body model concept, corresponding to an end-loaded geometrically nonlinear, large-deflection beam, was developed to help fulfill this need. In this paper, the pseudo-rigid-body equivalent spring stiffness is investigated and new modeling equations are proposed. The result is a simplified method of modeling the force/deflection relationships of large-deflection members in compliant mechanisms. Flexible segments which maintain a constant end angle are discussed, and an example mechanism is analyzed. The resulting models are valuable in the visualization of the motion of large-deflection systems, as well as the quick and efficient evaluation and optimization of compliant mechanism designs.

Type Synthesis of Compliant Mechanisms Employing a Simplified Approach to Segment Type

1994 ◽  
Author(s):  
Morgan D. Murphy ◽  
Ashok Midha ◽  
Larry L. Howell
Keyword(s):  
Rigid Body ◽  
Compliant Mechanisms ◽  
Compliant Mechanism ◽  
Type Synthesis ◽  
Simplified Approach ◽  
Design Procedures ◽  
Synthesis Techniques ◽  
Design Solutions ◽  
Synthesis Methodology

Abstract The formulation of design procedures for rigid-body mechanisms has benefited from the application of type-synthesis techniques. Therefore, with modifications to allow for inclusions of compliance, type synthesis is seen as a useful tool in the design of compliant mechanisms. Previous efforts have developed methods that result in a large number of possible design solutions to a given problem. This paper deals primarily with the development of a simplified compliant-mechanism type-synthesis methodology that limits the number of design solutions considered. The techniques are derived by modifying existing compliant mechanism type-synthesis techniques to yield a simpler model with greater pragmatic value.

Compliant Pantographs via the Pseudo-Rigid-Body Model

1998 ◽  
Author(s):  
Andrew J. Nielson ◽  
Larry L. Howell
Keyword(s):  
Rigid Body ◽  
Compliant Mechanisms ◽  
Compliant Mechanism ◽  
Test Results ◽  
Rigid Link ◽  
Body Model ◽  
Design Flexibility ◽  
Model Predictions ◽  
Rigid Body Model ◽  
Classical Mechanism

Abstract This paper uses a familiar classical mechanism, the pantograph, to demonstrate the utility of the pseudo-rigid-body model in the design of compliant mechanisms to replace rigid-link mechanisms, and to illustrate the advantages and limitations of the resulting compliant mechanisms. To demonstrate the increase in design flexibility, three different compliant mechanism configurations were developed for a single corresponding rigid-link mechanism. The rigid-link pantograph consisted of six links and seven joints, while the corresponding compliant mechanisms had no more than two links and three joints (a reduction of at least four links and four joints). A fourth compliant pantograph, corresponding to a rhomboid pantograph, was also designed and tested. The test results showed that the pseudo-rigid-body model predictions were accurate over a large range, and the mechanisms had displacement characteristics of rigid-link mechanisms in that range. The limitations of the compliant mechanisms included reduced range compared to their rigid-link counterparts. Also, the force-deflection characteristics were predicted by the pseudo-rigid-body model, but they did not resemble those for a rigid-link pantograph because of the energy storage in the flexible segments.

Sign in / Sign up

Export Citation Format

Share Document