Aerodynamic Performance Improvement of a Wing Model Using an Array of Slotted Synthetic Jets

2020 ◽  
Vol 142 (10) ◽  
Author(s):  
Pramod Salunkhe ◽  
Yanhua Wu ◽  
Hui Tang
Keyword(s):  
Flow Separation ◽  
Performance Enhancement ◽  
Lift Coefficient ◽  
Power Spectra ◽  
Leading Edge ◽  
Aerodynamic Performance ◽  
Synthetic Jets ◽  
Force Balance ◽  
Flow Separation Control ◽  
Wing Model

Abstract This work deals with the improvement in aerodynamic performance of a NACA0025 wing model using an array of slotted synthetic jets (SJs). A novel SJ actuator was designed and located at 30% of the chord from the leading edge (LE). Time-resolved particle image velocimetry (TR-PIV), force balance, static pressure distribution, and hotwire measurements were carried out in a subsonic wind tunnel to assess the performance enhancement due to the slotted SJ array. Initially, the SJ velocity was measured in quiescent flow condition at different actuation frequencies and amplifier voltages. Actuation at 1000 Hz and 200 V resulted in the highest blowing velocity of 10.5 m/s. Experiments were performed at various actuation frequencies, namely, 200, 600, and 1000 Hz. It was observed that actuation at 1000 Hz led to the highest increase in lift coefficient by 35.6% and reduction in average drag coefficient by 33%. TR-PIV measurements showed flow separation with flow reversal in the baseline case. After switching on the SJ array at 1000 Hz, the flow separation was completely eliminated. The momentum transfer from the highenergy primary flow to the retarding boundarylayer flow and actuation of SJ in a particular frequency range was observed to be the mechanisms for the flow separation control. Subsequently, fast Fourier transform (FFT) power spectra of hotwire data were computed from 40% to 80% of the chord. The FFT power spectra showed the successful stabilization of the flow field at the actuation of 1000 Hz.

A New Class of Synthetic Jet Actuators—Part II: Application to Flow Separation Control

2005 ◽  
Vol 127 (2) ◽  
pp. 377-387 ◽  
Author(s):  
J. L. Gilarranz ◽  
L. W. Traub ◽  
O. K. Rediniotis
Keyword(s):  
Flow Separation ◽  
Lift Coefficient ◽  
Surface Flow ◽  
Synthetic Jet ◽  
Force Balance ◽  
Separation Control ◽  
Stream Velocity ◽  
Moderate Amount ◽  
Flow Separation Control ◽  
Synthetic Jet Actuator

In this work we present the application of the new synthetic jet actuator (SJA) to flow separation control over a NACA 0015 wing. The actuator is compact enough to fit in the interior of the wing that has a chord of 0.375 m. The wing was tested in the Texas A&M University Aerospace Engineering 3 ft×4 ft wind tunnel. An experimental investigation into the effects of the synthetic jet actuator on the performance of the wing is described. Emphasis is placed on the capabilities of the actuator to control the separation of the flow over the wing at high angles of attack. The results include force balance measurements, on surface and off surface flow visualization, surface pressure measurements, and wake surveys. All of the reported tests were performed at a free-stream velocity of 35 m/s, corresponding to a Reynolds number of 8.96×105. The angle of attack was varied from −2.0 deg to 29.0 deg. For the results presented, at angles of attack lower than 10 deg, the actuator has minimal effects. At higher angles of attack, the SJA delays the onset of stall. The use of the actuator causes an 80% increase in the maximum lift coefficient, while the angle at which stall occurs is increased from 12 to 18 deg. The drag on the wing is decreased as a consequence of SJA actuation. For angles of attack larger than 18 deg, where the wing experiences massive separation, the SJA still provides a moderate amount of lift augmentation compared to the unforced case. At angles of attack larger than 25°, a larger frequency of actuation is required to produce significant effects.

scholarly journals Flow Separation Control of Backward-Facing Step Airfoil NACA0015 by Blowing Technique

2019 ◽  
Vol 12 (1) ◽  
pp. 99-119
Author(s):  
Khuder N. Abed
Keyword(s):  
Flow Separation ◽  
Numerical Study ◽  
Leading Edge ◽  
Distribution Coefficients ◽  
Open Circuit ◽  
Experimental Investigations ◽  
Backward Facing Step ◽  
Ansys Fluent ◽  
Flow Separation Control ◽  
Naca 0015

The aim of this paper is to control the flow separation above backward-facing step (BFS) airfoil type NACA 0015 by blowing method. The flow field over airfoil has been studied both experimentally and computationally. The study was divided into two parts: a practical study through which NACA 0015 type with a backward -facing step (located at 44.4% c from leading edge) on the upper surface containing blowing holes parallel to the airfoil chord was used. The tests were done over two-dimensional airfoil in an open circuit suction subsonic wind tunnel with flow velocity 25m/s to obtain the pressure distribution coefficients. A numerical study was done by using ANSYS Fluent software version 16.0 on three models of NACA 0015, the first one has backward-facing step without blowing, the second with single blowing holes and the third have multi blowing holes technique. Both studies (experimental and numerical) were done at low Reynolds number (Re=4.4x105) and all models have chord length 0.27m.The experimental investigations and CFD simulations have been performed on the same geometry dimensions, it has been observed that the flow separation on the airfoil can be delayed by using  velocity blowing (30m/s) on the upper surface. The multi blowing holes with velocity improved the aerodynamics properties.The multi blowing holes and single blowing hole thesame effect onpressure distribution coefficients

scholarly journals Numerical Analysis of Wind Turbine Airfoil Aerodynamic Performance with Leading Edge Bump

2015 ◽  
Vol 2015 ◽  
pp. 1-8 ◽  
Author(s):  
Majid Asli ◽  
Behnam Mashhadi Gholamali ◽  
Abolghasem Mesgarpour Tousi
Keyword(s):  
Wind Turbine ◽  
Control Method ◽  
Flow Behavior ◽  
Renewable Energy Sources ◽  
Lift Coefficient ◽  
Turbine Blades ◽  
Vortex Generator ◽  
Leading Edge ◽  
Suction Side ◽  
Aerodynamic Performance

Aerodynamic performance improvement of wind turbine blade is the key process to improve wind turbine performance in electricity generated and energy conversion in renewable energy sources concept. The flow behavior on wind turbine blades profile and the relevant phenomena like stall can be improved by some modifications. In the present paper, Humpback Whales flippers leading edge protuberances model as a novel passive stall control method was investigated on S809 as a thick airfoil. The airfoil was numerically analyzed by CFD method in Reynolds number of 106and aerodynamic coefficients in static angle of attacks were validated with the experimental data reported by Somers in NREL. Therefore, computational results for modified airfoil with sinusoidal wavy leading edge were presented. The results revealed that, at low angles of attacks before the stall region, lift coefficient decreases slightly rather than baseline model. However, the modified airfoil has a smooth stall trend while baseline airfoil lift coefficient decreases sharply due to the separation which occurred on suction side. According to the flow physics over the airfoils, leading edge bumps act as vortex generator so vortices containing high level of momentum make the flow remain attached to the surface of the airfoil at high angle of attack and prevent it from having a deep stall.

scholarly journals Improvement of Aerodynamic Performance of Cambered Airfoils Using Leading-Edge Slots

2017 ◽  
Vol 139 (5) ◽  
Author(s):  
Saman Beyhaghi ◽  
Ryoichi S. Amano
Keyword(s):  
Lift Coefficient ◽  
Leading Edge ◽  
Aerodynamic Performance ◽  
Bottom Surface ◽  
Original Design ◽  
Local Pressure ◽  
Maximum Increase ◽  
Average Improvement ◽  
Length Width ◽  
Inlet Angle

Feasibility of increasing lift and decreasing drag by drilling narrow span-wide channels near the leading edge of NACA 4412 airfoils is investigated. It is proposed to drill two-segment slots that allow some of the incoming air to flow through them and then exit from the bottom surface of the airfoil. Such slots can result in an increased local pressure and thereby higher lift. Length, width, inlet angle, and exit angle of slots are varied to determine optimum configurations. Aerodynamic performance at different angles of attack (AoAs) and the chord-based Reynolds number of 1.6 × 106 is investigated. It is concluded that longer and narrower slots with exit streams more aligned with the air flowing below the airfoil can result in a higher lift. Also, in order to keep the slotted airfoils beneficial for AoAs greater than zero, it is proposed to (a) slightly lower the slot position with respect to the original design and (b) tilt up the first-leg by a few degrees. For the best design case considered, an average improvement of 8% is observed for lift coefficient over the entire range of AoA (with the maximum increase of 15% for AoA = 0), without any significant drag penalty.

Flow separation control of NACA-2412 airfoil with bio-inspired nose

2019 ◽  
Vol 91 (7) ◽  
pp. 1058-1066 ◽  
Author(s):  
Mohamed Arif Raj Mohamed ◽  
Ugur Guven ◽  
Rajesh Yadav
Keyword(s):  
Flow Control ◽  
Flow Separation ◽  
Control Method ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Separation Control ◽  
Cetacean Species ◽  
Aerodynamic Efficiency ◽  
Content Type ◽  
Flow Separation Control

Purpose The purpose of this paper is to achieve an optimum flow separation control over the airfoil using passive flow control method by introducing bio-inspired nose near the leading edge of the NACA 2412 airfoil. Design/methodology/approach Two distinguished methods have been implemented on the leading edge of the airfoil: forward facing step, which induces multiple accelerations at low angle of attack, and cavity/backward facing step, which creates recirculating region (axial vortices) at high angle of attack. Findings The porpoise airfoil (optimum bio-inspired nose airfoil) delays the flow separation and improves the aerodynamic efficiency by increasing the lift and decreasing the parasitic drag. The maximum increase in aerodynamic efficiency is 22.4 per cent, with an average increase of 8.6 per cent at all angles of attack. Research limitations/implications The computational analysis has been done for NACA 2412 airfoil at low subsonic speed. Practical implications This design improves the aerodynamic performance and increases structural strength of the aircraft wing compared to other conventional high-lift devices and flow-control devices. Originality/value Different bio-inspired nose designs which are inspired by the cetacean species have been analysed for NACA 2412 airfoil, and optimum nose design (porpoise airfoil) has been found.

Flow separation control using a bio-inspired nose for NACA 4 and 6 series airfoils

2021 ◽  
Vol 93 (2) ◽  
pp. 251-266
Author(s):  
Mohamed Arif Raj Mohamed ◽  
Rajesh Yadav ◽  
Ugur Guven
Keyword(s):  
Flow Control ◽  
Flow Separation ◽  
Control Method ◽  
Leading Edge ◽  
Aircraft Design ◽  
Separation Control ◽  
Cetacean Species ◽  
Aerodynamic Efficiency ◽  
Content Type ◽  
Flow Separation Control

Purpose This paper aims to achieve an optimum flow separation control over the airfoil using a passive flow control method by introducing a bio-inspired nose near the leading edge of the National Advisory Committee for Aeronautics (NACA) 4 and 6 series airfoil. In addition, to find the optimised leading edge nose design for NACA 4 and 6 series airfoils for flow separation control. Design/methodology/approach Different bio-inspired noses that are inspired by the cetacean species have been analysed for different NACA 4 and 6 series airfoils. Bio-inspired nose with different nose length, nose depth and nose circle diameter have been analysed on airfoils with different thicknesses, camber and camber locations to understand the aerodynamic flow properties such as vortex formation, flow separation, aerodynamic efficiency and moment. Findings The porpoise nose design that has a leading edge with depth = 2.25% of chord, length = 0.75% of chord and nose diameter = 2% of chord, delays the flow separation and improves the aerodynamic efficiency. Average increments of 5.5% to 6° in the lift values and decrements in parasitic drag (without affecting the pitching moment) for all the NACA 4 and 6 series airfoils were observed irrespective of airfoil geometry such as different thicknesses, camber and camber location. Research limitations/implications The two-dimensional computational analysis is done for different NACA 4 and 6 series airfoils at low subsonic speed. Practical implications This design improves aerodynamic performance and increases the structural strength of the aircraft wing compared to other conventional high lift devices and flow control devices. This universal leading edge flow control device can be adapted to aircraft wings incorporated with any NACA 4 and 6 series airfoil. Social implications The results would be of significant interest in the fields of aircraft design and wind turbine design, lowering the cost of energy and air travel for social benefits. Originality/value Different bio-inspired nose designs that are inspired by the cetacean species have been analysed for NACA 4 and 6 series airfoils and universal optimum nose design (porpoise airfoil) is found for NACA 4 and 6 series airfoils.

Sign in / Sign up

Export Citation Format

Share Document