Temperature of Grinding Carbide with Castor Oil-based MoS2 Nanofluid Minimum Quantity Lubrication

2021 ◽  
pp. 1-30
Author(s):  
Menghua Sui ◽  
Changhe Li ◽  
Wentao Wu ◽  
Min Yang ◽  
Hafiz Muhammad Ali ◽  
...  
Keyword(s):  
Working Conditions ◽  
Minimum Quantity Lubrication ◽  
Grinding Force ◽  
Cemented Carbide ◽  
Machining Process ◽  
Minimum Quantity ◽  
Lubrication Performance ◽  
Nanofluid Minimum Quantity Lubrication ◽  
G Ratio ◽  
Specific Grinding Force

Abstract Nanofluid minimum quantity lubrication (NMQL) has better stability, higher thermal conductivity, and excellent lubrication performance compared with traditional flood lubrication. The heat transfer model and finite difference model were established to verify the feasibility of NMQL conditions in grinding cemented carbide. Based on them, the grinding temperature of cemented carbide is calculated numerically. Results show that the grinding zone temperatures of flood grinding and NMQL are lower, 85.9 °C and 143.2 °C, respectively. Surface grinding experiments of cemented carbide YG8 under different working conditions are carried out. Dry grinding (227.2 °C) is used as the control group. Grinding zone temperatures of flood grinding, minimum quantity lubrication, and NMQL decrease by 64.2%, 39.5%, and 20.4% respectively. The error is 6.3% between theoretical calculation temperature and experimental measurement temperature. Based on machining process parameters (specific grinding force, force ratio) and experimental results (microstructure of grinding wheel, workpiece, and grinding debris), the effects of different working conditions on wheel wear are studied. NMQL achieves the highest G ratio of 6.45, the smallest specific grinding force, and the smallest Fn/Ft ratio of 2.84, which further proves that NMQL is suitable for grinding cemented carbide.

A Review of Minimum Quantity Lubrication (MQL) based on Bibliometry

2020 ◽  
Vol 13 ◽  
Author(s):  
Gaurav Gaurav ◽  
Abhay Sharma ◽  
G S Dangayach ◽  
M L Meena
Keyword(s):  
Descriptive Analysis ◽  
Minimum Quantity Lubrication ◽  
Citation Network ◽  
Machining Process ◽  
Cutting Fluid ◽  
Future Research ◽  
Research Directions ◽  
Minimum Quantity ◽  
Research Areas ◽  
Future Research Directions

Background: Minimum quantity lubrication (MQL) is one of the most promising machining techniques that can yield a reduction in consumption of cutting fluid more than 90 % while ensuring the surface quality and tool life. The significance of the MQL in machining makes it imperative to consolidate and analyse the current direction and status of research in MQL. Objective: This study aims to assess global research publication trends and hot topics in the field of MQL among machining process. The bibliometric and descriptive analysis are the tools that the investigation aims to use for the data analysis of related literature collected from Scopus databases. Methods: Various performance parameters are extracted, such as document types and languages of publication, annual scientific production, total documents, total citations, and citations per article. The top 20 of the most relevant and productive sources, authors, affiliations, countries, word cloud, and word dynamics are assessed. The graphical visualisation of the bibliometric data is presented in terms of bibliographic coupling, citation, and co-citation network. Results: The investigation reveals that the International Journal of Machine Tools and Manufacture (2611 citations, 31 hindex) is the most productive journal that publishes on MQL. The most productive institution is the University of Michigan (32 publications), the most cited country is Germany (1879 citations), and the most productive country in MQL is China (124 publications). The study shows that ‘Cryogenic Machining’, ‘Sustainable Machining’, ‘Sustainability’, ‘Nanofluid’ and ‘Titanium alloy’ are the most recent keywords and indications of the hot topics and future research directions in the MQL field. Conclusion: The analysis finds that MQL is progressing in publications and the emerging with issues that are strongly associated with the research. This study is expected to help the researchers to find the most current research areas through the author’s keywords and future research directions in MQL and thereby expand their research interests.

scholarly journals Performance of Al2O3 nanofluids in minimum quantity lubrication in hard milling of 60Si2Mn steel using cemented carbide tools

2017 ◽  
Vol 9 (7) ◽  
pp. 168781401771061 ◽  
Author(s):  
Duc Tran Minh ◽  
Long Tran The ◽  
Ngoc Tran Bao
Keyword(s):  
Surface Roughness ◽  
Tool Life ◽  
Minimum Quantity Lubrication ◽  
High Hardness ◽  
Cemented Carbide ◽  
Cutting Fluid ◽  
Hard Milling ◽  
Minimum Quantity ◽  
Coated Carbide ◽  
Lubrication Conditions

In this article, an attempt has been made to explore the potential performance of Al2O3 nanoparticle–based cutting fluid in hard milling of hardened 60Si2Mn steel (50-52 HRC) under different minimum quantity lubrication conditions. The comparison of hard milling under minimum quantity lubrication conditions is done between pure cutting fluids and nanofluids (in terms of surface roughness, cutting force, tool wear, and tool life). Hard milling under minimum quantity lubrication conditions with nanofluid Al2O3 of 0.5% volume has shown superior results. The improvement in tool life almost 177%–230% (depending on the type of nanofluid) and the reduction in surface roughness and cutting forces almost 35%–60% have been observed under minimum quantity lubrication with Al2O3 nanofluids due to better tribological behavior as well as cooling and lubricating effects. The most outstanding result is that the uncoated cemented carbide insert can be effectively used in machining high-hardness steels (>50 HRC) while maintaining long tool life and good surface integrity (Ra = 0.08–0.35 µm; Rz = 0.5–2.0 µm, equivalent to finish grinding) rather than using the costlier tools like coated carbide, ceramic, and (P)CBN. Therefore, using hard nanoparticle–reinforced cutting fluid under minimum quantity lubrication conditions in practical manufacturing becomes very promising.

Performance of Low Cost 3D Printed Minimum Quantity Lubrication Applicator Using Palm Oil in Milling Steel

2020 ◽  
Vol 997 ◽  
pp. 85-92
Author(s):  
Abang Mohammad Nizam Abang Kamaruddin ◽  
Abdullah Yassin ◽  
Shahrol Mohamaddan ◽  
Syaiful Anwar Rajaie ◽  
Muhammad Isyraf Mazlan ◽  
...  
Keyword(s):  
Tool Wear ◽  
Cutting Forces ◽  
Cutting Tool ◽  
Low Cost ◽  
Minimum Quantity Lubrication ◽  
Machining Process ◽  
Cutting Condition ◽  
Dry Cutting ◽  
Minimum Quantity ◽  
Tool Performance

One of the most significant factors in machining process or metal cutting is the cutting tool performance. The rapid wear rate of cutting tools and cutting forces expend due to high cutting temperature is a critical problem to be solved in high-speed machining process, milling. Near-dry machining such as minimum quantity lubrication (MQL) is regarded as one of the solutions to solve this problem. However, the function of MQL in milling process is still uncertain so far which prevents MQL from widely being utilized in this specific machining process. In this paper, the mechanism of cutting tool performance such as tool wear and cutting forces in MQL assisted milling is investigated more comprehensively and the results are compared in three different cutting conditions which is dry cutting, wet cutting (flooding) and MQL. The MQL applicator is constructed from a household grade low-cost 3D printing technique. The chips surface of chips formation in each cutting condition is also observed using Scanning Electron Microscopy (SEM) machine. It is found out that wet cutting (flooding) is the best cutting performance compare to MQL and dry cutting. However, it can also be said that wet cutting and MQL produced almost the same value of tool wear and cutting forces as there is negligible differences in average tool wear and cutting forces between them based on the experiment conducted.

Sign in / Sign up

Export Citation Format

Share Document