Measurement of Heat Transfer and Flow Structures in a Closed Rotating Cavity

2022 ◽  
Author(s):  
Richard Jackson ◽  
Hui Tang ◽  
James Scobie ◽  
J. Michael Owen ◽  
Gary Lock
Keyword(s):  
Heat Transfer ◽  
Gas Turbines ◽  
Pressure Sensors ◽  
Flow Structures ◽  
Closed Cavity ◽  
Experimental Range ◽  
Wide Range ◽  
Industrial Gas Turbines ◽  
Induced Flow ◽  
Compressibility Effects

Abstract Buoyancy-induced flow occurs inside the rotating compressor cavities of gas turbines. These cavities are usually open at the inner radius, but in some industrial gas turbines, they are effectively closed. This paper presents measurements of the disc heat transfer and rotating flow structures in a closed cavity over a wide range of engine relevant conditions. These experimentally derived distributions of disc temperature and heat flux are the first of their kind to be published. The radial distribution of the non-dimensional disc temperature virtually collapsed onto a single curve over the full experimental range. There was a small, monotonic departure from this common curve with increasing Reynolds number; this was attributed to compressibility effects where the core temperature increases as the rotational speed increases. These results imply that, if compressibility effects are negligible, all rotating closed cavities should have a disc temperature distribution uniquely related to the geometry and disc material; this is of important practical use to the engine designer. Unsteady pressure sensors detected either three or four vortex pairs across the experimental range. The number of pairs changed with Grashof number, and the structures slipped relative to the rotating discs by less than 1% of the disc speed.

Measurement of Heat Transfer and Flow Structures in a Closed Rotating Cavity

2021 ◽  
Author(s):  
Richard W. Jackson ◽  
Hui Tang ◽  
James A. Scobie ◽  
J. Michael Owen ◽  
Gary D. Lock
Keyword(s):  
Heat Transfer ◽  
Gas Turbines ◽  
Pressure Sensors ◽  
Flow Structures ◽  
Closed Cavity ◽  
Experimental Range ◽  
Wide Range ◽  
Industrial Gas Turbines ◽  
Induced Flow ◽  
Compressibility Effects

Abstract Buoyancy-induced flow occurs inside the rotating compressor cavities of gas turbines. These cavities are usually open at the inner radius, but in some industrial gas turbines, they are effectively closed. This paper presents measurements of the disc heat transfer and rotating flow structures in a closed cavity over a wide range of engine relevant conditions. These experimentally derived distributions of disc temperature and heat flux are the first of their kind to be published. The radial distribution of the non-dimensional disc temperature virtually collapsed onto a single curve over the full experimental range. There was a small, monotonic departure from this common curve with increasing Reynolds number; this was attributed to compressibility effects where the core temperature increases as the rotational speed increases. These results imply that, if compressibility effects are negligible, all rotating closed cavities should have a disc temperature distribution uniquely related to the geometry and disc material; this is of important practical use to the engine designer. Unsteady pressure sensors detected either three or four vortex pairs across the experimental range. The number of pairs changed with Grashof number, and the structures slipped relative to the rotating discs by less than 1% of the disc speed.

Theoretical Model of Buoyancy-Induced Heat Transfer in Closed Compressor Rotors

2017 ◽  
Author(s):  
Hui Tang ◽  
J. Michael Owen
Keyword(s):  
Heat Transfer ◽  
Gas Turbines ◽  
Gravitational Acceleration ◽  
Centripetal Acceleration ◽  
Closed Cavity ◽  
Nusselt Numbers ◽  
Industrial Gas Turbines ◽  
Induced Flow ◽  
Cooling Air ◽  
Buoyancy Induced Flow

The cavities between the rotating compressor discs in aeroengines are open, and there is an axial throughflow of cooling air in the annular space between the centre of the discs and the central rotating compressor shaft. Buoyancy-induced flow occurs inside these open rotating cavities, with an exchange of heat and momentum between the axial throughflow and the air inside the cavity. However, even where there is no opening at the centre of the compressor discs — as is the case in some industrial gas turbines — buoyancy-induced flow can still occur inside the closed rotating cavities. The closed cavity also provides a limiting case for an open cavity when the axial clearance between the cobs — the bulbous hubs at the centre of compressor discs — is reduced to zero. Bohn and his co-workers at the University of Aachen have studied three different closed-cavity geometries, and they have published experimental data for the case where the outer cylindrical surface is heated and the inner surface is cooled. In this paper, a buoyancy model is developed in which it is assumed that the heat transfer from the cylindrical surfaces is analogous to laminar free convection from horizontal plates, with the gravitational acceleration replaced by the centripetal acceleration. The resulting equations, which have been solved analytically, show how the Nusselt numbers depend on both the geometry of the cavity and its rotational speed. The theoretical solutions show that compressibility effects in the core attenuate the Nusselt numbers, and there is a critical Reynolds number at which the Nusselt number will be a maximum. For the three cavities tested, the predicted Nusselt numbers are in generally good agreement with the measured values of Bohn et al. over a large range of Raleigh numbers up to values approaching 1012. The fact that the flow remains laminar even at these high Rayleigh numbers is attributed to the Coriolis accelerations suppressing turbulence in the cavity, which is consistent with recently-published results for open rotating cavities.

Theoretical Model of Buoyancy-Induced Heat Transfer in Closed Compressor Rotors

2017 ◽  
Vol 140 (3) ◽  
Author(s):  
Hui Tang ◽  
J. Michael Owen
Keyword(s):  
Heat Transfer ◽  
Gas Turbines ◽  
Gravitational Acceleration ◽  
Centripetal Acceleration ◽  
Closed Cavity ◽  
Nusselt Numbers ◽  
Industrial Gas Turbines ◽  
Induced Flow ◽  
Aero Engines ◽  
Buoyancy Induced Flow

The cavities between the rotating compressor disks in aero-engines are open, and there is an axial throughflow of cooling air in the annular space between the center of the disks and the central rotating compressor shaft. Buoyancy-induced flow occurs inside these open rotating cavities, with an exchange of heat and momentum between the axial throughflow and the air inside the cavity. However, even where there is no opening at the center of the compressor disks—as is the case in some industrial gas turbines—buoyancy-induced flow can still occur inside the closed rotating cavities. The closed cavity also provides a limiting case for an open cavity when the axial clearance between the cobs—the bulbous hubs at the center of compressor disks—is reduced to zero. Bohn and his co-workers at the University of Aachen have studied three different closed-cavity geometries, and they have published experimental data for the case where the outer cylindrical surface is heated and the inner surface is cooled. In this paper, a buoyancy model is developed in which it is assumed that the heat transfer from the cylindrical surfaces is analogous to laminar free convection from horizontal plates, with the gravitational acceleration replaced by the centripetal acceleration. The resulting equations, which have been solved analytically, show how the Nusselt numbers depend on both the geometry of the cavity and its rotational speed. The theoretical solutions show that compressibility effects in the core attenuate the Nusselt numbers, and there is a critical Reynolds number at which the Nusselt number will be a maximum. For the three cavities tested, the predicted Nusselt numbers are in generally good agreement with the measured values of Bohn et al. over a large range of Raleigh numbers up to values approaching 1012. The fact that the flow remains laminar even at these high Rayleigh numbers is attributed to the Coriolis accelerations suppressing turbulence in the cavity, which is consistent with recently published results for open rotating cavities.

The Design and Development of an Electrically Operated Fuel Control Valve for Industrial Gas Turbines

1991 ◽  
Author(s):  
A. G. Salsi ◽  
F. S. Bhinder
Keyword(s):  
Gas Turbines ◽  
Entire Range ◽  
Control Valve ◽  
Performance Characteristics ◽  
Design And Development ◽  
Wide Range ◽  
Industrial Gas Turbines

Industrial gas turbines operate over a wide range of combinations of loads and speeds. The fuel control valve must be designed to cover the entire range precisely. The design of an electrically operated fuel control valve is described and comparison between the predicted and measured performance characteristics is shown.

Heat Transfer Associated With Air-Water Spray Cooling of Forgings From High Temperatures

2001 ◽  
Author(s):  
J. Ward ◽  
M. de Oliveira ◽  
D. R. Garwood ◽  
R. A. Wallis
Keyword(s):  
Heat Transfer ◽  
Water Flow ◽  
Gas Turbines ◽  
Spray Cooling ◽  
Solution Temperature ◽  
Air Cooling ◽  
Water Spray ◽  
Transfer Rates ◽  
Wide Range ◽  
Water Spray Cooling

Abstract The desired mechanical properties of the nickel-based or titanium forgings used in gas turbines for aircraft and power generation applications can be controlled by varying the rate of cooling from the so-called solution temperature during an initial heat treatment process. The use of dilute air-water spray cooling of these forgings is a technique which can provide heat transfer rates lying between those associated with conventional oil quenching or convective air-cooling. Air assisted atomisation can result in fine sprays over a wide range of water flow rates and it has a further advantage in that the air “sweeps” the surface and hence helps to prevent the build up of deleterious vapour films at high surface temperatures. The paper presents experimental data for the heat transfer rates associated with the use of these sprays to cool surfaces from temperatures of approximately 800°C. Many forgings contain surface recesses, which can lead to build up or “pooling” of the water so that the effect of variations in surface geometry is also reported. Periodic interruption of the water flow is a technique which can be employed to provide additional control of the heat transfer rate, particularly at temperatures below 500°C so that data is also presented for pulsed sprays.

Experimental Identification of Steady-State Turbomachinery Heat Transfer Using Nondimensional Groups

2020 ◽  
Vol 142 (6) ◽  
Author(s):  
Markus Baumann ◽  
Christian Koch ◽  
Stephan Staudacher
Keyword(s):  
Heat Transfer ◽  
Steady State ◽  
Gas Turbines ◽  
Experimental Identification ◽  
Wide Range ◽  
Nonsteady State ◽  
Data Points ◽  
Steady State Heat ◽  
Steady State Heat Transfer ◽  
Turboshaft Engine

Abstract Diabatic performance modeling is a prerequisite for engine condition monitoring based on nonsteady-state data points (e.g., Putz et al. 2017, “Jet Engine Gas Path Analysis Based on Takeoff Performance Snapshots,” ASME J. Eng. Gas Turbines Power, 139(11), p. 111201.). The importance of diabatic effects increases with decreasing engine size. Steady-state diabatic modeling of turbomachinery components is presented using nondimensional parameters derived from a dimensional analysis. The resulting heat transfer maps are approximated using the analytic solution for a pipe. Experimental identification of the maps requires the measurement of casing and gas path temperatures. This approach is demonstrated successfully using a small turboshaft engine as a test vehicle. A limited amount of measurements was needed to generate a steady-state heat transfer map which is valid for a wide range of operating points.

Studies on Wake-Affected Heat Transfer Around the Circular Leading Edge of Blunt Body

1994 ◽  
Author(s):  
K. Funazaki
Keyword(s):  
Heat Transfer ◽  
Strouhal Number ◽  
Gas Turbines ◽  
Blunt Body ◽  
Leading Edge ◽  
Test Model ◽  
Flow Conditions ◽  
Transfer Enhancement ◽  
Wide Range ◽  
Experimental Works

Detailed measurements are performed about time-averaged beat transfer distributions around the leading edge of a blunt body which is affected by incoming periodic wakes from the upstream moving bars. The blunt body is a test model of a front portion of a turbine blade in gas turbines and consists of a semicircular cylindrical leading edge and a flat plate afterbody. A wide range of the steady and unsteady flow conditions are adopted as for the Reynolds number based on the diameter of the leading edge and the bar-passing Strouhal number. The measured heat transfer distributions indicate that the wakes passing over the leading edge cause significant increase in beat transfer before the separation and the higher Strouhal number results in higher heat transfer. From this experiment, a correlation for the heat transfer enhancement around the leading edge due to the periodic wakes is deduced as a function of the Stanton number and it is reviewed by comparison with the other experimental works.

Study of a Rich/Lean Staged Combustion Concept for Hydrogen at Gas Turbine Relevant Conditions

2013 ◽  
Author(s):  
Felipe Bolaños ◽  
Dieter Winkler ◽  
Felipe Piringer ◽  
Timothy Griffin ◽  
Rolf Bombach ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Carbon Capture ◽  
Flame Temperature ◽  
Nox Emissions ◽  
Hydrogen Fuel ◽  
Auto Ignition ◽  
Wide Range ◽  
The Rich

The combustion of hydrogen-rich fuels (> 80 % vol. H2), relevant for gas turbine cycles with “pre-combustion” carbon capture, creates great challenges in the application of standard lean premix combustion technology. The significant higher flame speed and drastically reduced auto-ignition delay time of hydrogen compared to those of natural gas, which is normally burned in gas turbines, increase the risk of higher NOX emissions and material damage due to flashback. Combustion concepts for gas turbines operating on hydrogen fuel need to be adapted to assure safe and low-emission combustion. A rich/lean (R/L) combustion concept with integrated heat transfer that addresses the challenges of hydrogen combustion has been investigated. A sub-scale, staged burner with full optical access has been designed and tested at gas turbine relevant conditions (flame temperature of 1750 K, preheat temperature of 400 °C and a pressure of 8 bar). Results of the burner tests have confirmed the capability of the rich/lean staged concept to reduce the NOx emissions for undiluted hydrogen fuel. The NOx emissions were reduced from 165 ppm measured without staging (fuel pre-conversion) to 23 ppm for an R/L design having a fuel-rich hydrogen pre-conversion of 50 % at a constant power of 8.7 kW. In the realized R/L concept the products of the first rich stage, which is ignited by a Pt/Pd catalyst (under a laminar flow, Re ≈ 1900) are combusted in a diffusion-flame-like lean stage (turbulent flow Re ≈ 18500) without any flashback risk. The optical accessibility of the reactor has allowed insight into the combustion processes of both stages. Applying OH-LIF and OH*-chemiluminescence optical techniques, it was shown that mainly homogeneous reactions at rich conditions take place in the first stage, questioning the importance of a catalyst in the system, and opening a wide range of optimization possibilities. The promising results obtained in this study suggest that such a rich/lean staged burner with integrated heat transfer could help to develop a new generation of gas turbine burners for safe and clean combustion of H2-rich fuels.

Advanced Catalytic Pilot for Low NOx Industrial Gas Turbines

2002 ◽  
Author(s):  
Hasan Karim ◽  
Kent Lyle ◽  
Shahrokh Etemad ◽  
Lance Smith ◽  
William Pfefferle ◽  
...  
Keyword(s):  
High Pressure ◽  
Surface Temperature ◽  
Gas Turbines ◽  
Lean Burn ◽  
Pressure Testing ◽  
Wide Range ◽  
Industrial Gas Turbines ◽  
Design And Testing ◽  
Pilot Burner ◽  
Load Conditions

This paper describes the design and testing of a catalytically-stabilized pilot burner for current and advanced Dry Low NOx (DLN) gas turbine combustors. In this paper, application of the catalytic pilot technology to industrial engines is described using Solar Turbines’ Taurus 70 engine. The objective of the work described is to develop the catalytic pilot technology and document the emission benefits of catalytic pilot technology when compared to higher, NOx producing pilots. The catalytic pilot was designed to replace the existing pilot in the existing DLN injector without major modification to the injector. During high pressure testing, the catalytic pilot showed no incidence of flashback or autoignition while operating over wide range of combustion temperatures. The catalytic reactor lit off at a temperature of approximately 598K (325°C/617°F) and operated at simulated 100% and 50% load conditions without a preburner. At high pressure, the maximum catalyst surface temperature was similar to that observed during atmospheric pressure testing and considerably lower than the surface temperature expected in lean-burn catalytic devices. In single injector rig testing, the integrated assembly of the catalytic pilot and Taurus 70 injector demonstrated NOx and CO emission less than 5 ppm @ 15% O2 for 100% and 50% load conditions along with low acoustics. The results demonstrate that a catalytic pilot burner replacing a diffusion flame or partially-premixed pilot in an otherwise DLN combustor can enable operation at conditions with substantially reduced NOx emissions.

Sign in / Sign up

Export Citation Format

Share Document