scholarly journals Measurements in Separated and Transitional Boundary Layers Under Low-Pressure Turbine Airfoil Conditions

2000 ◽  
Author(s):  
Ralph J. Volino ◽  
Lennart S. Hultgren
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Pressure Gradient ◽  
Boundary Layers ◽  
Free Stream ◽  
Separation Bubble ◽  
Low Pressure ◽  
Mean Velocity ◽  
Free Stream Turbulence ◽  
Low Pressure Turbine

Detailed velocity measurements were made along a flat plate subject to the same dimensionless pressure gradient as the suction side of a modern low-pressure turbine airfoil. Reynolds numbers based on wetted plate length and nominal exit velocity were varied from 50, 000 to 300, 000, covering cruise to takeoff conditions. Low and high inlet free-stream turbulence intensities (0.2% and 7%) were set using passive grids. The location of boundary-layer separation does not depend strongly on the free-stream turbulence level or Reynolds number, as long as the boundary layer remains non-turbulent prior to separation. Strong acceleration prevents transition on the upstream part of the plate in all cases. Both free-stream turbulence and Reynolds number have strong effects on transition in the adverse pressure gradient region. Under low free-stream turbulence conditions transition is induced by instability waves in the shear layer of the separation bubble. Reattachment generally occurs at the transition start. At Re = 50, 000 the separation bubble does not close before the trailing edge of the modeled airfoil. At higher Re, transition moves upstream, and the boundary layer reattaches. With high free-stream turbulence levels, transition appears to occur in a bypass mode, similar to that in attached boundary layers. Transition moves upstream, resulting in shorter separation regions. At Re above 200,000, transition begins before separation. Mean velocity, turbulence and intermittency profiles are presented.

scholarly journals Measurements in Separated and Transitional Boundary Layers Under Low-Pressure Turbine Airfoil Conditions

2000 ◽  
Vol 123 (2) ◽  
pp. 189-197 ◽  
Author(s):  
Ralph J. Volino ◽  
Lennart S. Hultgren
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Pressure Gradient ◽  
Boundary Layers ◽  
Free Stream ◽  
Separation Bubble ◽  
Low Pressure ◽  
Mean Velocity ◽  
Free Stream Turbulence ◽  
Low Pressure Turbine

Detailed velocity measurements were made along a flat plate subject to the same dimensionless pressure gradient as the suction side of a modern low-pressure turbine airfoil. Reynolds numbers based on wetted plate length and nominal exit velocity were varied from 50,000 to 300,000, covering cruise to takeoff conditions. Low and high inlet free-stream turbulence intensities (0.2 and 7 percent) were set using passive grids. The location of boundary-layer separation does not depend strongly on the free-stream turbulence level or Reynolds number, as long as the boundary layer remains nonturbulent prior to separation. Strong acceleration prevents transition on the upstream part of the plate in all cases. Both free-stream turbulence and Reynolds number have strong effects on transition in the adverse pressure gradient region. Under low free-stream turbulence conditions, transition is induced by instability waves in the shear layer of the separation bubble. Reattachment generally occurs at the transition start. At Re=50,000 the separation bubble does not close before the trailing edge of the modeled airfoil. At higher Re, transition moves upstream, and the boundary layer reattaches. With high free-stream turbulence levels, transition appears to occur in a bypass mode, similar to that in attached boundary layers. Transition moves upstream, resulting in shorter separation regions. At Re above 200,000, transition begins before separation. Mean velocity, turbulence, and intermittency profiles are presented.

Separated Flow Transition in a Low Pressure Turbine Cascade: Mean Flow and Turbulence Spectra

2003 ◽  
Author(s):  
Ralph J. Volino ◽  
Christopher G. Murawski
Keyword(s):  
Boundary Layer ◽  
Free Stream ◽  
Separation Bubble ◽  
Suction Side ◽  
Low Pressure ◽  
Turbine Cascade ◽  
Mean Flow ◽  
Turbulence Spectra ◽  
Free Stream Turbulence ◽  
Low Pressure Turbine

Boundary layer separation, transition and reattachment have been studied experimentally in a low-pressure turbine cascade. Cases with Reynolds numbers (Re) ranging from 50,000 to 200,000 (based on suction surface length and exit velocity) have been considered under low free-stream turbulence conditions. Mean and fluctuating velocity profiles and turbulence spectra are presented for streamwise locations along the suction side of one airfoil and in the wake downstream of the airfoils. Hot film gages on the suction side surface of the airfoil are used to measure the fluctuation level and the spectra of the fluctuations on the surface. Higher Re moves transition upstream. Transition is initiated in the shear layer over the separation bubble and leads to boundary layer reattachment. Peak frequencies in the boundary layer spectra match those found in similar cases in the literature, indicating that the important frequencies may be predictable. Spectra in the wake downstream of the airfoils were similar to the spectra in the boundary layer near the trailing edge of the airfoil. Comparisons to the literature indicate that small but measurable differences in the spectra of the low free-stream turbulence can have a significant effect on boundary layer reattachment.

Numerical and Experimental Studies on Separated Boundary Layers Over Ultra-High Lift Low-Pressure Turbine Cascade Airfoils With Variable Solidity: Effects of Free-Stream Turbulence

2008 ◽  
Author(s):  
Ken-Ichi Funazaki ◽  
Kazutoyo Yamada ◽  
Yasuhiro Chiba ◽  
Nozomi Tanaka
Keyword(s):  
Boundary Layers ◽  
Free Stream ◽  
Separation Bubble ◽  
Experimental Studies ◽  
Low Pressure ◽  
Freestream Turbulence ◽  
High Lift ◽  
Free Stream Turbulence ◽  
Low Pressure Turbine ◽  
Turbine Airfoils

This paper deals with LES investigation, along with measurements, on the interaction between inlet freestream turbulence and boundary layers with separation bubble over ultra-high lift low-pressure turbine airfoils. The cross section of the test airfoils is typical for highly-loaded LP turbines for civil aeroengines. The solidity of the cascade can be reduced by increasing the airfoil pitch by at least 25%, while maintaining the throat in the blade-to-blade passage. Reynolds number examined is 57,000, based on chord length and averaged exit velocity. Free-stream turbulence is about 0.85% (no grid condition) and 2.1% (with grid condition). Hot-wire probe measurements of the boundary layer are carried out to obtain time-averaged and time-resolved characteristics of the boundary layers under the influence of the freestream turbulence. A newly developed probe positioning tool, which is installed downstream of the cascade with minimal blockage, enables precise probe positioning along lines normal to the airfoil surface. Numerical analysis based on high-resolution LES (Large-Eddy Simulation) is executed to enhance the understanding of the flow field around the Ultra-High Lift and High Lift LP turbine airfoils. Emphasis is placed on the relationship of inherent instability of the shear layer of the separation bubble and the free-stream turbulence. Standard Smagorinsky model is employed for subgrid scale modeling. The flow solver used is an in-house code that was originally developed by one of the authors as FVM (Finite Volume Method)-based fully implicit and time-accurate Reynolds-Averaged Navier-Stokes code. Homogeneous isotropic turbulence created with SNGR (Stochastic Noise Generation and Radiation) method using von Karman-Pao turbulent energy spectrum is applied in the present study for the emulation of inlet turbulence.

Transition Mechanisms in Laminar Separated Flow Under Simulated Low Pressure Turbine Aerofoil Conditions

2012 ◽  
Vol 135 (1) ◽  
Author(s):  
Jerrit Dähnert ◽  
Christoph Lyko ◽  
Dieter Peitsch
Keyword(s):  
Reynolds Number ◽  
Separation Bubble ◽  
Separated Flow ◽  
Low Pressure ◽  
Main Flow ◽  
Test Facility ◽  
Flow Conditions ◽  
Laminar Separation ◽  
Free Stream Turbulence ◽  
Low Pressure Turbine

Based on detailed experimental work conducted at a low speed test facility, this paper describes the transition process in the presence of a separation bubble with low Reynolds number, low free-stream turbulence, and steady main flow conditions. A pressure distribution has been created on a long flat plate by means of a contoured wall opposite of the plate, matching the suction side of a modern low-pressure turbine aerofoil. The main flow conditions for four Reynolds numbers, based on suction surface length and nominal exit velocity, were varied from 80,000 to 300,000, which covers the typical range of flight conditions. Velocity profiles and the overall flow field were acquired in the boundary layer at several streamwise locations using hot-wire anemometry. The data given is in the form of contours for velocity, turbulence intensity, and turbulent intermittency. The results highlight the effects of Reynolds number, the mechanisms of separation, transition, and reattachment, which feature laminar separation-long bubble and laminar separation-short bubble modes. For each Reynolds number, the onset of transition, the transition length, and the general characteristics of separated flow are determined. These findings are compared to the measurement results found in the literature. Furthermore, the experimental data is compared with two categories of correlation functions also given in the literature: (1) correlations predicting the onset of transition and (2) correlations predicting the mode of separated flow transition. Moreover, it is shown that the type of instability involved corresponds to the inviscid Kelvin-Helmholtz instability mode at a dominant frequency that is in agreement with the typical ranges occurring in published studies of separated and free-shear layers.

Transition Mechanisms in Laminar Separated Flow Under Simulated Low Pressure Turbine Airfoil Conditions

2011 ◽  
Author(s):  
Jerrit Da¨hnert ◽  
Christoph Lyko ◽  
Dieter Peitsch
Keyword(s):  
Reynolds Number ◽  
Separation Bubble ◽  
Separated Flow ◽  
Low Pressure ◽  
Main Flow ◽  
Test Facility ◽  
Flow Conditions ◽  
Laminar Separation ◽  
Free Stream Turbulence ◽  
Low Pressure Turbine

Based on detailed experimental work conducted at a low speed test facility, this paper describes the transition process in the presence of a separation bubble with low Reynolds number, low free-stream turbulence, and steady main flow conditions. A pressure distribution has been created on a long flat plate by means of a contoured wall opposite of the plate, matching the suction side of a modern low-pressure turbine aerofoil. The main flow conditions for four Reynolds numbers, based on suction surface length and nominal exit velocity, were varied from 80,000 to 300,000, which covers the typical range of flight conditions. Velocity profiles and the overall flow field were acquired in the boundary layer at several streamwise locations using hot-wire anemometry. The data given is in the form of contours for velocity, turbulence intensity, and turbulent intermittency. The results highlight the effects of Reynolds number, the mechanisms of separation, transition, and reattachment, which feature laminar separation-long bubble and laminar separation-short bubble modes. For each Reynolds number, the onset of transition, the transition length, and the general characteristics of separated flow are determined. These findings are compared to the measurement results found in the literature. Furthermore, the experimental data is compared with two categories of correlation functions also given in the open literature: (1) correlations predicting the onset of transition and (2) correlations predicting the mode of separated flow transition. Moreover, it is shown that the type of instability involved corresponds to the inviscid Kelvin-Helmholtz instability mode at a dominant frequency that is in agreement with the typical ranges occurring in published studies of separated and free-shear layers.

Separated Flow Measurements on a Highly Loaded Low-Pressure Turbine Airfoil

2008 ◽  
Author(s):  
Ralph J. Volino
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Separation Bubble ◽  
Boundary Layer Separation ◽  
Low Pressure ◽  
Transition To Turbulence ◽  
Suction Surface ◽  
Airfoil Surface ◽  
Flow Measurements ◽  
Low Pressure Turbine

Boundary layer separation, transition and reattachment have been studied on a new, very high lift, low-pressure turbine airfoil. Experiments were done under low freestream turbulence conditions on a linear cascade in a low speed wind tunnel. Pressure surveys on the airfoil surface and downstream total pressure loss surveys were documented. Velocity profiles were acquired in the suction side boundary layer at several streamwise locations using hot-wire anemometry. Cases were considered at Reynolds numbers (based on the suction surface length and the nominal exit velocity from the cascade) ranging from 25,000 to 330,000. In all cases the boundary layer separated, but at high Reynolds number the separation bubble remained very thin and quickly reattached after transition to turbulence. In the low Reynolds number cases, the boundary layer separated and did not reattach, even when transition occurred. This behavior contrasts with previous research on other airfoils, in which transition, if it occurred, always induced reattachment, regardless of Reynolds number.

Study of Flow Controlling on LP Turbine at Different Reynolds Number

2012 ◽  
Author(s):  
Muhammad Aqib Chishty ◽  
Hossein Raza Hamdani ◽  
Khalid Parvez ◽  
Muhammad Nafees Mumtaz Qadri
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Flow Separation ◽  
Separation Bubble ◽  
Low Pressure ◽  
Control Flow ◽  
Loss Coefficient ◽  
Shear Stresses ◽  
Low Pressure Turbine ◽  
Lp Turbine

Active and passive techniques have been used in the past, to control flow separation. Numerous studies were published on controlling and delaying the flow separation on low pressure turbine. In this study, a single dimple (i.e. passive device) is engraved on the suction side of LP turbine cascade T106A. The main aim of this research is to find out the optimum parameters of dimple i.e. diameter (D) and depth (h) which can produce strong enough vortex that can control the flow either in transition or fully turbulent phase. Furthermore, this optimal dimple is engraved to suppress the boundary layer separation at different Reynolds number (based on the chord length and inlet velocity). The dimple of different depth and diameter are used to find the optimal depth to diameter ratio. Computational results show that the optimal ratio of depth to diameter (h/D) for dimple is 0.0845 and depth to grid boundary layer (h/δ) is 0.5152. This optimized dimple efficiently reduces the normalized loss coefficient and it is found that the negative values of shear stresses found in uncontrolled case are being removed by the dimple. After that, dimple of optimized parameters are used to suppress the laminar separation bubble at different Re∼25000, 50000 and 91000. It was noticed that the dimple did not reduce the losses at Re∼25000. But at Re∼50000, it produced such a strong vortex that reduced the normalized loss coefficient to 25%, while 5% losses were reduced at Re∼91000. It can be concluded that the optimized dimple effectively controlled flow separation and reduced normalized loss coefficient from Re 25000 to 91000. As the losses are decreased, this will increase the low pressure turbine efficiency and reduce its fuel consumption.

scholarly journals Reynolds, Mach and free-stream turbulence effects on the flow in a low-pressure turbine

2021 ◽  
pp. 1-17
Author(s):  
Maxime Fiore ◽  
Nicolas Gourdain
Keyword(s):  
Reynolds Number ◽  
Mach Number ◽  
Free Stream ◽  
Guide Vane ◽  
Flow Behavior ◽  
Suction Side ◽  
Boundary Layer Separation ◽  
Low Pressure ◽  
Free Stream Turbulence ◽  
Low Pressure Turbine

Abstract This paper presents the Large Eddy Simulation of a Low-Pressure Turbine Nozzle Guide Vane for different Reynolds (Re) and Mach numbers (Ma) with or without inlet turbulence prescribed. The analysis is based on a slice of a LPT blading representative of a midspan flow. The characteristic Re of the LPT can vary by a factor of four between take-off and cruise conditions. In addition, the LPT operates at different Ma and the incident flow can have significant levels of turbulence due to upstream blade wakes. The paper investigates numerically using LES the flow around a LPT blading with three different Reynolds number Re = 175'000 (cruise), 280'000 (mid-level altitude) and 500'000 (take-off) keeping the same characteristic Mach number Ma = 0.2 and three different Mach number Ma = 0.2, 0.5 and 0.8 keeping the same Reynolds number Re= 280'000. These different simulations are performed with 0% Free Stream Turbulence (FST) followed by inlet turbulence (6% FST). The study focuses on different flow characteristics: pressure distribution around the blade, near-wall flow behavior, loss generation and Turbulent Kinetic Energy budget. The results show an earlier boundary layer separation on the aft of the blade suction side when the Re is increased while the free-stream turbulence delays separation. The TKE budget shows the predominant effect of the turbulent production and diffusion in the wake, the axial evolution of these different terms being relatively insensitive to Re and Ma.

Experimental Investigation of Free Stream Turbulence Effects on Flow Separation

2003 ◽  
Author(s):  
Mahmoud Ardebili ◽  
Yiannis Andreopoulos
Keyword(s):  
Boundary Layer ◽  
Experimental Investigation ◽  
Reynolds Number ◽  
Pressure Gradient ◽  
Flow Separation ◽  
Large Scale ◽  
Free Stream ◽  
Pressure Coefficient ◽  
Free Stream Turbulence ◽  
Vorticity Flux

An experimental investigation of a separated boundary layer flow has been attempted which has been created by perturbing a flat plate flow with a favorable pressure gradient immediately followed by an adverse pressure gradient. The aim of the research program is possible control of flow separation by means of free stream turbulence. The flow is configured in a large-scale low speed wind tunnel where measurements of turbulence can be obtained with high spatial and temporal resolution. A model has been designed by using CFD analysis. Mean wall pressure and vorticity flux measurements are reported in this paper. Twelve experiments with three different mesh size grids at three different Reynolds numbers have been carried out. Three bulk flow parameters seem to characterize the flow: The Reynolds number of the boundary layer, Re+, the Reynolds number of the flow through the grid, ReM, and the solidity of the grid. It was found that the pressure coefficient depends weakly on the solidity of the grids. Vorticity flux also depends on the grid used to generate free stream turbulence. The location of maximum or minimum vorticity flux moves upstream at higher ReM.

Sign in / Sign up

Export Citation Format

Share Document