Rotating Instabilities in an Axial Compressor Originating From the Fluctuating Blade Tip Vortex

2000 ◽  
Author(s):  
R. Mailach ◽  
I. Lehmann ◽  
K. Vogeler
Keyword(s):  
Rotor Blade ◽  
Laser Doppler Anemometry ◽  
Stability Limit ◽  
Rotor Blades ◽  
Tip Clearance ◽  
Tip Vortex ◽  
Experimental Investigations ◽  
Flow Phenomenon ◽  
Low Speed ◽  
Blade Tip

Rotating instabilities (RI) have been observed in axial flow fans, centrifugal compressors as well as in low-speed and high-speed axial compressors. They are responsible for the excitation of high amplitude rotor blade vibrations and noise generation. This flow phenomenon moves relative to the rotor blades and causes periodic vortex separations at the blade tips and an axial reversed flow through the tip clearance of the rotor blades. The paper describes experimental investigations of RI in the Dresden Low-Speed Research Compressor (LSRC). The objective is to show that the fluctuation of the blade tip vortex is responsible for the origination of this flow phenomenon. RI have been found at operating points near the stability limit of the compressor with relatively large tip clearance of the rotor blades. The application of time-resolving sensors in both fixed and rotating frame of reference enables a detailed description of the circumferential structure and the spatial development of this unsteady flow phenomenon, which is limited to the blade tip region. Laser-Doppler-Anemometry (LDA) within the rotor blade passages and within the tip clearance as well as unsteady pressure measurements on the rotor blades show the structure of the blade tip vortex. It will be shown that the periodical interaction of the blade tip vortex of one blade with the flow at the adjacent blade is responsible for the generation of a rotating structure with high mode orders, termed as rotating instability (RI).

Rotating Instabilities in an Axial Compressor Originating From the Fluctuating Blade Tip Vortex

2000 ◽  
Vol 123 (3) ◽  
pp. 453-460 ◽  
Author(s):  
R. Mailach ◽  
I. Lehmann ◽  
K. Vogeler
Keyword(s):  
Rotor Blade ◽  
Laser Doppler Anemometry ◽  
Stability Limit ◽  
Rotor Blades ◽  
Tip Clearance ◽  
Tip Vortex ◽  
Experimental Investigations ◽  
Flow Phenomenon ◽  
Low Speed ◽  
Blade Tip

Rotating instabilities (RIs) have been observed in axial flow fans and centrifugal compressors as well as in low-speed and high-speed axial compressors. They are responsible for the excitation of high amplitude rotor blade vibrations and noise generation. This flow phenomenon moves relative to the rotor blades and causes periodic vortex separations at the blade tips and an axial reversed flow through the tip clearance of the rotor blades. The paper describes experimental investigations of RIs in the Dresden Low-Speed Research Compressor (LSRC). The objective is to show that the fluctuation of the blade tip vortex is responsible for the origination of this flow phenomenon. RIs have been found at operating points near the stability limit of the compressor with relatively large tip clearance of the rotor blades. The application of time-resolving sensors in both fixed and rotating frame of reference enables a detailed description of the circumferential structure and the spatial development of this unsteady flow phenomenon, which is limited to the blade tip region. Laser-Doppler-anemometry (LDA) within the rotor blade passages and within the tip clearance as well as unsteady pressure measurements on the rotor blades show the structure of the blade tip vortex. It will be shown that the periodical interaction of the blade tip vortex of one blade with the flow at the adjacent blade is responsible for the generation of a rotating structure with high mode orders, termed a rotating instability.

Periodical Unsteady Flow Within a Rotor Blade Row of an Axial Compressor: Part I — Flow Field at Midspan

2007 ◽  
Author(s):  
Ronald Mailach ◽  
Ingolf Lehmann ◽  
Konrad Vogeler
Keyword(s):  
Flow Field ◽  
Unsteady Flow ◽  
Pressure Distribution ◽  
Rotor Blade ◽  
Laser Doppler Anemometry ◽  
Pressure Sensors ◽  
Stability Limit ◽  
Rotor Blades ◽  
Experimental Investigations ◽  
Blade Row

In this two-part paper results of the periodical unsteady flow field within the third rotor blade row of the four-stage Dresden Low-Speed Research Compressor are presented. The main part of the experimental investigations was performed using Laser-Doppler-Anemometry. Results of the flow field at several spanwise positions between midspan and rotor blade tip will be discussed. In addition time-resolving pressure sensors at midspan of the rotor blades provide information about the unsteady profile pressure distribution. In part I of the paper the flow field at midspan of the rotor blade row will be discussed. Different aspects of the blade row interaction process are considered for the design point and an operating point near the stability limit. The periodical unsteady blade-to-blade velocity field is dominated by the incoming stator wakes, while the potential effect of the stator blades is of minor influence. The inherent vortex structures and the negative jet effect, which is coupled to the wake appearance, are clearly resolved. Furthermore the time-resolved profile pressure distribution of the rotor blades is discussed. Although the negative jet effect within the rotor blade passage is very pronounced the rotor blade pressure distribution is nearly independent from the convectively propagating chopped stator wakes.

Periodical Unsteady Flow Within a Rotor Blade Row of an Axial Compressor—Part II: Wake-Tip Clearance Vortex Interaction

2008 ◽  
Vol 130 (4) ◽  
Author(s):  
Ronald Mailach ◽  
Ingolf Lehmann ◽  
Konrad Vogeler
Keyword(s):  
Flow Field ◽  
Unsteady Flow ◽  
Rotor Blade ◽  
Laser Doppler Anemometry ◽  
Pressure Sensors ◽  
Tip Clearance ◽  
Experimental Investigations ◽  
Blade Row ◽  
Blade Tip ◽  
Tip Clearance Vortex

In this two-part paper, results of the periodical unsteady flow field within the third rotor blade row of the four-stage Dresden low-speed research compressor are presented. The main part of the experimental investigations was performed using laser Doppler anemometry. Results of the flow field at several spanwise positions between midspan and rotor blade tip will be discussed. In addition, time-resolving pressure sensors at midspan of the rotor blades provide information about the unsteady profile pressure distribution. In Part II of the paper, the flow field in the rotor blade tip region will be discussed. The experimental results reveal a strong periodical interaction of the incoming stator wakes and the rotor blade tip clearance vortices. Consequently, in the rotor frame of reference, the tip clearance vortices are periodical with the stator blade passing frequency. Due to the wakes, the tip clearance vortices are separated into different segments. Along the mean vortex trajectory, these parts can be characterized by alternating patches of higher and lower velocities and flow turning or subsequent counter-rotating vortex pairs. These flow patterns move downstream along the tip clearance vortex path in time. As a result of the wake influence, the orientation and extension of the tip clearance vortices as well as the flow blockage periodically vary in time.

Experimental Investigations Into Pressure Field in Tip Clearance of Shrouded Rotor Blades

2002 ◽  
Author(s):  
Krzysztof Kosowski ◽  
Marian Piwowarski
Keyword(s):  
Pressure Distribution ◽  
Pressure Pulsation ◽  
Pressure Field ◽  
Rotor Blades ◽  
Tip Clearance ◽  
Experimental Investigations ◽  
Pressure Pulsations ◽  
Blade Tip ◽  
Shrouded Rotor ◽  
Blade Tip Clearance

The experimental investigations into the pressure field in the shroud clearance were performed on a one-stage air model turbine of impulse type. Measurements of pressure distribution were carried out for different rotor eccentricities, different values of axial gap and of rotor-stator misalignment, different rotor speeds and different turbine load. The experimental investigations proved that: a) the pressure in the blade tip clearance is not stationary but it pulsates, b) the effect of nozzle trailing edge can be observed in the blade shroud clearance, c) for a given turbine output, the rotor-stator eccentricity and rotor-stator misalignment appear the most important parameters influencing the pressure distribution in the shroud clearance. Aiming to investigate the pressure pulsation transmission through the leakage flow in the blade shroud clearances, pulsations of different amplitudes and frequencies were excited in the turbine inlet duct and corresponding changes of pressure were measured along the shroud width, followed by appropriate harmonic analysis. The investigations were performed for forced pulsations with frequencies ranging from 1Hz to 8 Hz. In all the examined cases, the frequency of pressure pulsations remained unchanged, while the amplitude of the pulsation decreased gradually along the tip clearance. The frequency of these pressure pulsations in the tip clearance was equal to the frequency of the pressure pulsation at the turbine stage inlet and to the frequency of pressure pulsation at the turbine flow passage’s exit.

Periodical Unsteady Flow Within a Rotor Blade Row of an Axial Compressor: Part II — Wake–Tip Clearance Vortex Interaction

2007 ◽  
Author(s):  
Ronald Mailach ◽  
Ingolf Lehmann ◽  
Konrad Vogeler
Keyword(s):  
Flow Field ◽  
Unsteady Flow ◽  
Rotor Blade ◽  
Pressure Sensors ◽  
Tip Clearance ◽  
Experimental Investigations ◽  
Lower Velocity ◽  
Blade Row ◽  
Blade Tip ◽  
Tip Clearance Vortex

In this two-part paper results of the periodical unsteady flow field within the third rotor blade row of the four-stage Dresden Low-Speed Research Compressor are presented. The main part of the experimental investigations was performed using Laser-Doppler-Anemometry. Results of the flow field at several spanwise positions between midspan and rotor blade tip will be discussed. In addition time-resolving pressure sensors at midspan of the rotor blades provide information about the unsteady profile pressure distribution. In part II of the paper the flow field in the rotor blade tip region will be discussed. The experimental results reveal a strong periodical interaction of the incoming stator wakes and the rotor blade tip clearance vortices. Consequently, in the rotor frame of reference the tip clearance vortices are periodical with the stator blade passing frequency. Due to the wakes the tip clearance vortices are separated into different segments. Along the mean vortex trajectory these parts can be characterised by alternating patches of higher and lower velocity and flow turning or subsequent counterrotating vortex pairs. These flow patterns move downstream along the tip clearance vortex path in time. As a result of the wake influence the orientation and extension of the tip clearance vortices as well as the flow blockage periodically vary in time.

Effects of 3D Aerofoil Tip Clearance Variation on a 4-Stage Low Speed Compressor

2006 ◽  
Author(s):  
Thomas Tschirner ◽  
Erik Johann ◽  
Ralf Mu¨ller ◽  
Konrad Vogeler
Keyword(s):  
Rotor Blades ◽  
Tip Clearance ◽  
Experimental Investigations ◽  
Blade Design ◽  
Baseline Design ◽  
Low Speed ◽  
Significant Difference ◽  
The Common ◽  
Radial Gap ◽  
End Wall

The aerodynamic performance of turbomachinery airfoils and therefore the overall efficiency of an engine are strongly dependent on the design of the near end wall sections of blades and vanes. In addition, good compressor stability can only be achieved if the running clearance is as small as allowed for save operation. In the engine the radial gap varies in size due to thermal effects and deterioration as well as transient maneuvers. Since the width of the running clearance can hardly be reduced, a new aerofoil sectional design for cantilevered vanes has been introduced to improve compressor stability over its whole range of operation. The baseline design and the new improved concept have been tested and analyzed for different clearance widths (TC1…TC3) on the rotor blades and cantilevered stator vanes. A baseline configuration featuring two-dimensional airfoils has been used as a datum to develop a more advanced design applying sweep and dihedral at the stacking axes. The running clearance on rotors and the radial gap on cantilevered stators were increased in three steps. Both numerical and experimental investigations had been carried out to verify the effect of variable running clearances on modified end wall sections. Experimental and numerical investigations have shown the effect of bow and sweep within this low speed application does not fully support the common theory of unloaded end wall sections as discussed in various publications. For the 2D blade design the common theory has been proven by both numerical and experimental evaluations. The 3D blade design configuration (BUILD IX) features a significant difference in efficiency sensitivity due to tip clearance width variation, whereas numerical prediction suggested improved compressor performance and stability. Measurements has shown higher losses at this configuration.

Experimental Demonstration of the Tip Clearance Flow Resonance Behind Compressor Non-Synchronous Vibration

2008 ◽  
Author(s):  
Jean Thomassin ◽  
Huu Duc Vo ◽  
Njuki W. Mureithi
Keyword(s):  
Shear Layer ◽  
Rotor Blade ◽  
Operating Conditions ◽  
Rotor Blades ◽  
Tip Clearance ◽  
Tip Clearance Flow ◽  
Experimental Apparatus ◽  
Clearance Flow ◽  
Blade Tip ◽  
Blade Tip Clearance

Non-Synchronous Vibration (NSV) is a particular type of aero-elastic phenomenon where the rotor blades vibrate at non-integral multiples of the shaft rotational frequencies. NSV behaviour appears similar to off-design stall flutter but with a particular blade tip flow evolution. This paper demonstrates the link between NSV and the resonance induced by the tip clearance flow, based on a proposed hypothesis. At off-design operating conditions, the rotor blade tip clearance shear layer flow can evolve tangentially. It is proposed that this tangential flow becomes a support for an acoustic feedback wave that settles between rotor blades. The feedback wave is driven by the blade vibratory motion. This forms a closed loop system where the feedback wave synchronizes the shear layer vortical structures with the blade vibration frequency. Depending on the blade tip local temperature, and when the feedback wavelength matches within one or two blade pitches, the system becomes resonant and very high vibrations can occur on the blade. An axial stage compressor test rig is used to look into the underlying mechanism behind NSV. The experimental apparatus consists of the first stage of a High Pressure Compressor (HPC) driven by an electric motor. The test section is built to minimize the effects of the adjacent stator blade rows to isolate the role of rotor blade tip clearance flow on NSV. Sensitivity studies are carried out to assess the effects of the rotor blade tip clearance and inlet temperature on NSV. Finally, evidence of the staging phenomena, inherent to the proposed NSV mechanism, is experimentally obtained.

The Tip Clearance Flow Resonance Behind Axial Compressor Nonsynchronous Vibration

2011 ◽  
Vol 133 (4) ◽  
Author(s):  
Jean Thomassin ◽  
Huu Duc Vo ◽  
Njuki W. Mureithi
Keyword(s):  
Shear Layer ◽  
Rotor Blade ◽  
Operating Conditions ◽  
Rotor Blades ◽  
Tip Clearance ◽  
Tip Clearance Flow ◽  
Experimental Apparatus ◽  
Clearance Flow ◽  
Blade Tip ◽  
Blade Tip Clearance

Nonsynchronous vibration (NSV) is a particular type of aero-elastic phenomenon, where the rotor blades vibrate at nonintegral multiples of the shaft rotational frequencies. NSV behavior appears similar to off-design stall flutter but with a particular blade tip flow evolution. This paper demonstrates the link between NSV and the resonance induced by the tip clearance flow based on a proposed hypothesis and experimental confirmation. At off-design operating conditions, the rotor blade tip clearance shear layer flow can evolve tangentially. It is proposed that this tangential flow becomes a support for an acoustic feedback wave that settles between rotor blades. The feedback wave is driven by the blade vibratory motion and synchronizes the shear layer vortical structures with the blade vibration frequency. Depending on the blade tip local temperature, and when the feedback wavelength matches within one or two blade pitches, the system becomes resonant and very high vibrations can occur on the blade. An axial stage compressor test rig is set-up to look into the underlying mechanism behind NSV through targeted measurements using both static and rotating instrumentation. The experimental apparatus consists of the first stage of a high pressure compressor driven by an electric motor. The test-section is built to minimize the effects of the adjacent stator blade rows in order to isolate the role of rotor blade tip clearance flow on NSV. Sensitivity studies are carried out to assess and demonstrate the effects of the rotor blade tip clearance and inlet temperature on NSV and validate the predicted resonance for NSV occurrence under various conditions. Vibrations and surface pressure data from adjacent blades are collected to demonstrate the predicted interactions between neighboring rotor blades. Finally, evidence of the staging phenomenon, inherent to the proposed NSV mechanism, is experimentally obtained. All the data obtained are consistent with and thus in support of the proposed mechanism for NSV.

Measurements of the Tip Clearance Flow for a High-Reynolds-Number Axial-Flow Rotor

1995 ◽  
Vol 117 (4) ◽  
pp. 522-532 ◽  
Author(s):  
W. C. Zierke ◽  
K. J. Farrell ◽  
W. A. Straka
Keyword(s):  
Reynolds Number ◽  
Flow Visualization ◽  
Vortex Core ◽  
Rotor Blade ◽  
High Reynolds Number ◽  
Tip Clearance ◽  
Tip Leakage Vortex ◽  
Tip Leakage ◽  
Blade Tip ◽  
High Reynolds

A high-Reynolds-number pump (HIREP) facility has been used to acquire flow measurements in the rotor blade tip clearance region, with blade chord Reynolds numbers of 3,900,000 and 5,500,000. The initial experiment involved rotor blades with varying tip clearances, while a second experiment involved a more detailed investigation of a rotor blade row with a single tip clearance. The flow visualization on the blade surface and within the flow field indicate the existence of a trailing-edge separation vortex, a vortex that migrates radially upward along the trailing edge and then turns in the circumferential direction near the casing, moving in the opposite direction of blade rotation. Flow visualization also helps in establishing the trajectory of the tip leakage vortex core and shows the unsteadiness of the vortex. Detailed measurements show the effects of tip clearance size and downstream distance on the structure of the rotor tip leakage vortex. The character of the velocity profile along the vortex core changes from a jetlike profile to a wakelike profile as the tip clearance becomes smaller. Also, for small clearances, the presence and proximity of the casing endwall affects the roll-up, shape, dissipation, and unsteadiness of the tip leakage vortex. Measurements also show how much circulation is retained by the blade tip and how much is shed into the vortex, a vortex associated with high losses.

Investigation of Helicopter Rotor-Blade-Tip-Vortex Alleviation Using a Slotted Tip

AIAA Journal ◽  
2004 ◽  
Vol 42 (3) ◽  
pp. 524-535 ◽  
Author(s):  
Yong Oun Han ◽  
J. Gordon Leishman
Keyword(s):  
Rotor Blade ◽  
Tip Vortex ◽  
Helicopter Rotor ◽  
Helicopter Rotor Blade ◽  
Blade Tip
Sign in / Sign up

Export Citation Format

Share Document