Evaluation of Unsteady CFD Methods by Their Application to a Transonic Propfan Stage

2001 ◽  
Author(s):  
S. Schmitt ◽  
F. Eulitz ◽  
L. Wallscheid ◽  
A. Arnone ◽  
M. Marconcini
Keyword(s):  
Numerical Methods ◽  
Navier Stokes ◽  
Test Case ◽  
Flow Angle ◽  
Laser Measurements ◽  
General Flow ◽  
Blade Row ◽  
Flow Features ◽  
Blade Row Interaction ◽  
Good Agreement

The accuracy in predicting the unsteady aerodynamic blade-row-interaction of two state-of-the-art Navier-Stokes codes is evaluated within the current paper. The general flow features of the test case — a transonic research propfan stage — are described in brief as far as necessary to understand the detailed comparisons. The calculated unsteady velocity and flow angle distributions at various axial planes of the stage are compared to data from unsteady laser measurements. The general flow features of the propfan are very well reproduced by the numerical methods and a good agreement is also obtained in comparison to the measured data. One important outcome of the comparison is the good agreement of both numerical methods with the unsteady fluctuations measured in the experiment.

scholarly journals Navier-Stokes and Potential Calculations of Axial Spacing Effect on Vortical and Potential Disturbances and Gust Response in an Axial Compressor

1995 ◽  
Author(s):  
Meng-Hsuan Chung ◽  
Andrew M. Wo
Keyword(s):  
Lower Order ◽  
Spacing Effect ◽  
Axial Compressor ◽  
Interaction Effects ◽  
Moving Frame ◽  
Navier Stokes ◽  
Blade Row ◽  
Vortical Disturbance ◽  
Blade Row Interaction ◽  
Gust Response

The effect of blade row axial spacing on vortical and potential disturbances and gust response is studied for a compressor stator/rotor configuration near design and at high loadings using 2D incompressible Navier-Stokes and potential codes, both written for multistage calculations. First, vortical and potential disturbances downstream of the isolated stator in the moving frame are defined; these disturbances exclude blade row interaction effects. Then, vortical and potential disturbances for the stator/rotor configuration are calculated for axial gaps of 10%, 20%, and 30% chord. Results show that the potential disturbance is uncoupled; the potential disturbance calculated from the isolated stator configuration is a good approximation for that from the stator/rotor configuration for all three axial gaps. The vortical disturbance depends strongly on blade row interactions. Low order modes of vortical disturbance are of substantial magnitude and decay much more slowly downstream than do those of potential disturbance. Vortical disturbance decays linearly with increasing mode except very close to the stator trailing edge. For a small axial gap, lower order modes of both vortical and potential disturbances must be included to determine the rotor gust response.

An Accelerated 3D Navier–Stokes Solver for Flows in Turbomachines

2010 ◽  
Vol 133 (2) ◽  
Author(s):  
Tobias Brandvik ◽  
Graham Pullan
Keyword(s):  
Graphics Processing Units ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Linear Scaling ◽  
Test Case ◽  
Processing Unit ◽  
Central Processing ◽  
Order Of Magnitude ◽  
Graphics Processing ◽  
Good Agreement

A new three-dimensional Navier–Stokes solver for flows in turbomachines has been developed. The new solver is based on the latest version of the Denton codes but has been implemented to run on graphics processing units (GPUs) instead of the traditional central processing unit. The change in processor enables an order-of-magnitude reduction in run-time due to the higher performance of the GPU. The scaling results for a 16 node GPU cluster are also presented, showing almost linear scaling for typical turbomachinery cases. For validation purposes, a test case consisting of a three-stage turbine with complete hub and casing leakage paths is described. Good agreement is obtained with previously published experimental results. The simulation runs in less than 10 min on a cluster with four GPUs.

Aerodynamic Origin of Rotor-Rotor Interaction Noise From Unducted Propulsors

2013 ◽  
Author(s):  
Florian Danner ◽  
Christofer Kendall-Torry ◽  
Hans-Peter Kau
Keyword(s):  
Stokes Equations ◽  
Navier Stokes ◽  
Propagation Characteristics ◽  
Propulsion Systems ◽  
Navier Stokes Equations ◽  
Pressure Distributions ◽  
Blade Row ◽  
Open Rotor ◽  
Blade Row Interaction ◽  
Insight Into

The sound arising from blade row interaction in open rotor propulsion systems is known to significantly contribute to overall noise emissions. The present paper therefore addresses the origination of rotor-rotor interaction noise from a pair of unducted counter-rotating fans. The focus is on the aerodynamic mechanisms that involve sound generation, in order to provide the physical understanding required to find noise-reducing means. Detailed insight into the underlying phenomena is provided on the basis of numerical simulations applying the unsteady Reynolds-averaged Navier-Stokes equations. The interaction mechanisms are identified by extracting the time-dependent disturbances of the flow field in the respective rotor relative frame of reference. Conclusions on the sources of interaction noise and potential noise-reducing means are drawn by evaluating polar directivities, blade surface pressure distributions and propagation characteristics.

Unsteady Aerodynamical Blade Row Interaction in a New Multistage Research Turbine: Part 2 — Numerical Investigation

2001 ◽  
Author(s):  
Wolfgang Höhn ◽  
Ralf Gombert ◽  
Astrid Kraus
Keyword(s):  
Boundary Layer ◽  
Grid Method ◽  
Low Pressure ◽  
Equation Model ◽  
Navier Stokes ◽  
Viscous Boundary Layer ◽  
Low Pressure Turbine ◽  
Blade Row ◽  
Multistage Turbine ◽  
Blade Row Interaction

This paper is the second part of a two part paper, which describes in part one the experimental setup and results of a new multistage turbine. Part two presents results of unsteady viscous flow calculations based on cold flow experiments of that three stage low pressure turbine. The present paper emphasizes the investigation of stator-stator interaction of a low pressure turbine section of a commercial jet engine. Different positions for the second and third stator are studied numerically and experimentally with respect to the blade row interaction, unsteady blade loading and unsteady boundary layer effects. A time accurate Reynolds averaged Navier-Stokes solver is applied for the computations. Turbulence is modeled using the Spalart-Allmaras one equation model turbulence model and the influence of modern transition models on the unsteady flow predictions is investigated. The integration of the governing equations in time is performed by a four stage Runge-Kutta scheme, which is accelerated by a two grid method in the viscous boundary layer around the blades and alternatively by a dual time stepping method. At the inlet and outlet reflecting or non-reflecting boundary conditions are used. The quasi 3D calculations are conducted on a stream surface around midspan allowing a varying stream tube thickness. In particular, the flow field with respect to time averaged and unsteady quantities such as surface pressure, vorticity, unsteady velocity field and skin friction are compared with the experiments conducted in the cold air flow test rig.

A Numerical Investigation of the Interaction Between Rotor Bow Waves and Upstream Wake Generators in a Transonic Compressor Stage

2003 ◽  
Author(s):  
Gregory Bloch ◽  
James Loellbach ◽  
Chunill Hah
Keyword(s):  
Numerical Investigation ◽  
Rotor Blade ◽  
Similar Case ◽  
Axial Compressor ◽  
Navier Stokes ◽  
Transonic Compressor ◽  
Blade Row ◽  
Transonic Axial Compressor ◽  
Main Effects ◽  
Blade Row Interaction

A numerical investigation of unsteady blade row interaction in a transonic axial compressor was performed. The compressor consists of an upstream wake generator (WG) blade row followed by a rotor blade row. Blade row interaction consists of two main effects: the downstream influence on the rotor flowfield of wakes and unsteady vortices shed from the wake generator, and the upstream influence on the wake generator of the rotor bow shock waves. An unsteady, two-dimensional, Navier-Stokes simulation was performed at the 75% span location of the compressor. Results from the numerical simulation are compared to previously reported numerical results and to experimental measurements from a similar case.

scholarly journals Wake Vorticity Decay and Blade Response in an Axial Compressor With Varying Axial Gap

1999 ◽  
Author(s):  
A. M. Wo ◽  
M. H. Chung ◽  
S. J. Chang ◽  
S. F. Lee
Keyword(s):  
Large Scale ◽  
Axial Compressor ◽  
Navier Stokes ◽  
Rotor Wake ◽  
Blade Loading ◽  
Wake Interaction ◽  
Blade Row ◽  
Unsteady Force ◽  
Gap Spacing ◽  
Blade Row Interaction

This paper addresses the decay of rotor wake vorticity for a rotor/stator axial compressor, with the axial gap between blade rows being 10, 20 and 30 percent chord, and at both design and high loading levels. Experiments were conducted in a large-scale, low-speed axial compressor. Navier-Stokes calculations were also executed. Both data and Navier-Stokes results reveal that the decay of rotor wake vorticity increases substantially as the axial gap decreases; the decay for 10 percent gap is about twice that of 30 percent. Increased time-mean blade loading causes the vorticity decay to also increase, with this effect more pronounced for large axial gap than small. At the stator inlet mid-pitch location, the wake maximum vorticity for 10 and 30 percent chord gap cases being nearly the same (differ by 3.8%) at design loading. The corresponding stator unsteady force agrees within 5.2%. Variation of vorticity decay with axial gap is directly linked to the change in potential disturbance by the downstream stator on the rotor wake due to the change in gap spacing. This suggests that the stator potential disturbance causes the upstream rotor wake to decay at an increased rate which, in turns, results in a lowered level of stator response compared to that without this stator/wake interaction effect. Thus, in this context, blade row interaction is considered beneficial.

An Accelerated 3D Navier-Stokes Solver for Flows in Turbomachines

2009 ◽  
Author(s):  
Tobias Brandvik ◽  
Graham Pullan
Keyword(s):  
Graphics Processing Units ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Linear Scaling ◽  
Test Case ◽  
Processing Unit ◽  
Central Processing ◽  
Order Of Magnitude ◽  
Graphics Processing ◽  
Good Agreement

A new three-dimensional Navier-Stokes solver for flows in turbomachines has been developed. The new solver is based on the latest version of the Denton codes, but has been implemented to run on Graphics Processing Units (GPUs) instead of the traditional Central Processing Unit (CPU). The change in processor enables an order-of-magnitude reduction in run-time due to the higher performance of the GPU. Scaling results for a 16 node GPU cluster are also presented, showing almost linear scaling for typical turbomachinery cases. For validation purposes, a test case consisting of a three-stage turbine with complete hub and casing leakage paths is described. Good agreement is obtained with previously published experimental results. The simulation runs in less than 10 minutes on a cluster with four GPUs.

scholarly journals Navier–Stokes and Potential Calculations of Axial Spacing Effect on Vortical and Potential Disturbances and Gust Response in an Axial Compressor

1997 ◽  
Vol 119 (3) ◽  
pp. 472-481 ◽  
Author(s):  
M.-H. Chung ◽  
A. M. Wo
Keyword(s):  
Spacing Effect ◽  
Axial Compressor ◽  
Leading Edge ◽  
Moving Frame ◽  
Navier Stokes ◽  
Two Dimensional ◽  
Blade Row ◽  
Vortical Disturbance ◽  
Blade Row Interaction ◽  
Gust Response

The effect of blade row axial spacing on vortical and potential disturbances and gust response is studied for a compressor stator/rotor configuration near design and at high loadings using two-dimensional incompressible Navier–Stokes and potential codes, both written for multistage calculations. First, vortical and potential disturbances downstream of the isolated stator in the moving frame are defined; these disturbances exclude blade row interaction effects. Then, vortical and potential disturbances for the stator/rotor configuration are calculated for axial gaps of 10, 20, and 30 percent chord. Results show that the potential disturbance is uncoupled locally; the potential disturbance calculated from the isolated stator configuration is a good approximation for that from the stator/rotor configuration upstream of the rotor leading edge at the locations studied. The vortical disturbance depends strongly on blade row interactions. Low-order modes of vortical disturbance are of substantial magnitude and decay much more slowly downstream than do those of potential disturbance. Vortical disturbance decays linearly with increasing mode except very close to the stator trailing edge. For a small axial gap, e.g., 10 percent chord, both vortical and potential disturbances must be included to determine the rotor gust response.

scholarly journals Effect of Rotor–Stator Interaction on Impeller Performance in Centrifugal Compressors

1999 ◽  
Vol 5 (2) ◽  
pp. 135-146 ◽  
Author(s):  
K. Sato ◽  
L. He
Keyword(s):  
Navier Stokes ◽  
Test Case ◽  
Steady Flows ◽  
Centrifugal Compressors ◽  
Vaned Diffuser ◽  
Rotor Stator Interaction ◽  
Flow Through ◽  
And Performance ◽  
Unsteady Effects ◽  
Blade Row Interaction

A 3-D unsteady thin-layer Navier-Stokes code has been used to calculate the flow through a centrifugal compressor stage. The validation of the code for steady flows in centrifugal compressors was conducted for the Krain’s impeller with a vaneless diffuser as a test case and the numerical results were compared with the experimental results. The predicted flow field and performance agreed well with the experimental data. An unsteady stage solution was then conducted with this impeller followed by a generic low-solidity vaned-diffuser to examine the unsteady effects on the impeller performance. The computational results showed a stabilising effect of the blade row interaction.

scholarly journals Numerical simulation of compressible cavitating two-phase flows with a pressure-based solver

2017 ◽  
Author(s):  
Marco Cristofaro ◽  
Wilfried Edelbauer ◽  
Manolis Gavaises ◽  
Phoevos Koukouvinis
Keyword(s):  
Stokes Equations ◽  
Navier Stokes ◽  
Test Case ◽  
Time Step ◽  
Two Phase ◽  
Navier Stokes Equations ◽  
Liquid Phases ◽  
Flow Features ◽  
Liquid Evaporation ◽  
Semi Empirical

This work intends to study the effect of compressibility on throttle flow simulations with a pressure–based solver.The simple micro throttle geometry allows easier access for obtaining experimental data compared to a real injector, but still maintaining the main flow features. For this reasons it represents a meaningful and well reported benchmark for validation of numerical methods developed for cavitating injector flows.An implicit pressure–based compressible solver is used on the filtered Navier–Stokes equations. Thus, no stability limitation is applied on the time step. A common pressure field is computed for all phases, but different velocity fields are solved for each phase, following the multi–fluid approach. The liquid evaporation rate is evaluated with a Rayleigh–Plesset equation based cavitation model and the Coherent Structure Model is adopted as closure for the sub–grid scales in the momentum equation.The aim of this study is to show the capabilities of the pressure–based solver to deal with both vapor and liquid phases considered compressible. A comparison between experimental results and compressible simulations is presented. Time–averaged vapor distribution and velocity profiles are reported and discussed.  The distribution of pressure maxima on the surface and the results from a semi–empirical erosion model are in good agreement with the erosion locations observed in the experiments. This test case aims to represent a benchmark for furtherapplication of the methodology to industrial relevant cases.DOI: http://dx.doi.org/10.4995/ILASS2017.2017.4629

Sign in / Sign up

Export Citation Format

Share Document