Numerical and Experimental Investigation of Secondary Flow in a High Speed Compressor Stator

1995 ◽  
Author(s):  
Y. Ohkita ◽  
H. Kodama ◽  
O. Nozaki ◽  
K. Kikuchi ◽  
A. Tamura
Keyword(s):  
Numerical Simulation ◽  
Experimental Investigation ◽  
Shear Flow ◽  
Secondary Flow ◽  
Total Pressure ◽  
High Speed ◽  
Experimental Studies ◽  
Three Dimensional ◽  
Three Dimensional Flow ◽  
Performance Recovery

A series of numerical and experimental studies have been conducted to understand the mechanism of loss generation in a high speed compressor stator with inlet radial shear flow over the span. In this study, numerical simulation is extensively used to investigate the complex three-dimensional flow in the cascades and to interpret the phenomena appeared in the high speed compressor tests. It has been shown that the inlet radial shear flow generated by upstream rotor had a significant influence on the stator secondary flow, and consequently on the total pressure loss. Redesign of the stator aiming at the reduction of loss by controlling secondary flow has been carried out and the resultant performance recovery was successfully demonstrated both numerically and experimentally.

Numerical and Experimental Investigation of Secondary Flow in a High-Speed Compressor Stator

1997 ◽  
Vol 119 (2) ◽  
pp. 169-175
Author(s):  
Y. Ohkita ◽  
H. Kodama ◽  
O. Nozaki ◽  
K. Kikuchi ◽  
A. Tamura
Keyword(s):  
Numerical Simulation ◽  
Experimental Investigation ◽  
Shear Flow ◽  
Secondary Flow ◽  
Total Pressure ◽  
High Speed ◽  
Experimental Studies ◽  
Three Dimensional ◽  
Three Dimensional Flow ◽  
Performance Recovery

A series of numerical and experimental studies have been conducted to understand the mechanism of loss generation in a high-speed compressor stator with inlet radial shear flow over the span. In this study, numerical simulation is extensively used to investigate the complex three-dimensional flow in the cascades and to interpret the phenomena that appeared in the high-speed compressor tests. It has been shown that the inlet radial shear flow generated by the upstream rotor had a significant influence on the stator secondary flow, and consequently on the total pressure loss. Redesign of the stator aiming at the reduction of loss by controlling secondary flow has been carried out and the resultant performance recovery was successfully demonstrated both numerically and experimentally.

An Experimental Arrangement for the Measurement of the Pressure Distribution on High Speed Rotating Blade Rows

1956 ◽  
Author(s):  
K. Leist
Keyword(s):  
Experimental Investigation ◽  
Pressure Distribution ◽  
High Speed ◽  
Three Dimensional ◽  
Axial Flow ◽  
Three Dimensional Flow ◽  
Research Staff ◽  
Rotating Blade ◽  
Flow Through ◽  
Turbine Blading

For several years past, the research staff of the Institute for Turbomachines of the Aachen Technical University has carried out measurements on rotating turbine blading. This program is part of a comprehensive effort directed toward the experimental investigation of the three-dimensional flow through axial-flow turbomachines.

Effect of Wake Passing on Unsteady Aerodynamic Performance in a Turbine Stage

2006 ◽  
Author(s):  
K. Yamada ◽  
K. Funazaki ◽  
K. Hiroma ◽  
M. Tsutsumi ◽  
Y. Hirano ◽  
...  
Keyword(s):  
Secondary Flow ◽  
Three Dimensional ◽  
Suction Side ◽  
Turbine Stage ◽  
Three Dimensional Flow ◽  
Unsteady Aerodynamic ◽  
Unsteady Effect ◽  
Unsteady Rans ◽  
Wake Passing ◽  
Stage Efficiency

In the present work, unsteady RANS simulations were performed to clarify several interesting features of the unsteady three-dimensional flow field in a turbine stage. The unsteady effect was investigated for two cases of axial spacing between stator and rotor, i.e. large and small axial spacing. Simulation results showed that the stator wake was convected from pressure side to suction side in the rotor. As a result, another secondary flow, which counter-rotated against the passage vortices, was periodically generated by the stator wake passing through the rotor passage. It was found that turbine stage efficiency with the small axial spacing was higher than that with the large axial spacing. This was because the stator wake in the small axial spacing case entered the rotor before mixing and induced the stronger counter-rotating vortices to suppress the passage vortices more effectively, while the wake in the large axial spacing case eventually promoted the growth of the secondary flow near the hub due to the migration of the wake towards the hub.

scholarly journals Investigation of Flow Behavior around Corotating Blades in a Double-Spindle Lawn Mower Deck

2005 ◽  
Vol 2005 (1) ◽  
pp. 77-89 ◽  
Author(s):  
W. Chon ◽  
R. S. Amano
Keyword(s):  
Flow Pattern ◽  
High Speed ◽  
Flow Behavior ◽  
Flow Analysis ◽  
Experimental Studies ◽  
Three Dimensional ◽  
Video Camera ◽  
Sound Level ◽  
Lawn Mower ◽  
Level Meter

When the airflow patterns inside a lawn mower deck are understood, the deck can be redesigned to be efficient and have an increased cutting ability. To learn more, a combination of computational and experimental studies was performed to investigate the effects of blade and housing designs on a flow pattern inside a1.1mwide corotating double-spindle lawn mower deck with side discharge. For the experimental portion of the study, air velocities inside the deck were measured using a laser Doppler velocimetry (LDV) system. A high-speed video camera was used to observe the flow pattern. Furthermore, noise levels were measured using a sound level meter. For the computational fluid dynamics (CFD) work, several arbitrary radial sections of a two-dimensional blade were selected to study flow computations. A three-dimensional, full deck model was also developed for realistic flow analysis. The computational results were then compared with the experimental results.

Direct Numerical Simulation of Drops in Three Dimensional Viscoelastic Simple Shear Flows

2001 ◽  
Author(s):  
Shriram B. Pillapakkam ◽  
Pushpendra Singh
Keyword(s):  
Numerical Simulation ◽  
Shear Flow ◽  
Direct Numerical Simulation ◽  
Viscoelastic Fluid ◽  
Simple Shear ◽  
Polymer Concentration ◽  
Three Dimensional ◽  
Simple Shear Flow ◽  
Splitting Technique

Abstract A three dimensional finite element scheme for Direct Numerical Simulation (DNS) of viscoelastic two phase flows is implemented. The scheme uses the Level Set Method to track the interface and the Marchuk-Yanenko operator splitting technique to decouple the difficulties associated with the governing equations. Using this numerical scheme, the shape of Newtonian drops in a simple shear flow of viscoelastic fluid and vice versa are analyzed as a function of Capillary number, Deborah number and polymer concentration. The viscoelastic fluid is modeled via the Oldroyd-B model. The role of viscoelastic stresses in deformation of a drop subjected to simple shear flow and its effect on the steady state shape is analyzed. Our results compare favorably with existing experimental data and also help in understanding the role of viscoelastic stresses in drop deformation.

Sign in / Sign up

Export Citation Format

Share Document