Finite Element Analysis of Thermomechanical Contact of an Elastomeric O-Ring Seal

1997 ◽  
Author(s):  
Baojiu Lin ◽  
David W. Nicholson
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Constitutive Model ◽  
Element Model ◽  
Support Design ◽  
Element Analysis ◽  
Ring Seal ◽  
Deformable Materials ◽  
Elastomeric Seals ◽  
Thermomechanical Contact

This study concerns the development of a finite element model to support design improvements in elastomeric seals subject to high temperature and pressure, such as in aircraft engines. Existing finite element codes familiar to the authors do not couple thermal and mechanical fields, nor do they implement thermomechanical contact models suitable for highly deformable materials. Recently, the authors have introduced a thermohyperelastic constitutive model for near-incompressible elastomers. In two subsequent studies, using the constitutive model, a method has been introduced for finite element analysis of coupled thermomechanical response, including boundary contributions due to large deformation and variable contact. A new thermomechanical contact model has also been introduced to accommodate the softness of elastomers. The method has been implemented in a special purpose code which concerns a seal compressed into a well. Several computations are used to validate the code. Simulations of a seal in an idealized geometry indicate rapid pressure increase with increasing compression and temperature.

Finite Element Analysis of Nonuniformity of Tires with Imperfections5

2007 ◽  
Vol 35 (3) ◽  
pp. 226-238 ◽  
Author(s):  
K. M. Jeong ◽  
K. W. Kim ◽  
H. G. Beom ◽  
J. U. Park
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Radial Force ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Dimensional Finite Element ◽  
Force Variation ◽  
Three Dimensional Finite Element

Abstract The effects of variations in stiffness and geometry on the nonuniformity of tires are investigated by using the finite element analysis. In order to evaluate tire uniformity, a three-dimensional finite element model of the tire with imperfections is developed. This paper considers how imperfections, such as variations in stiffness or geometry and run-out, contribute to detrimental effects on tire nonuniformity. It is found that the radial force variation of a tire with imperfections depends strongly on the geometrical variations of the tire.

scholarly journals Comparison of Tooth- and Bone-Borne Appliances on the Stress Distributions and Displacement Patterns in the Facial Skeleton in Surgically Assisted Rapid Maxillary Expansion—A Finite Element Analysis (FEA) Study

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1152
Author(s):  
Rafał Nowak ◽  
Anna Olejnik ◽  
Hanna Gerber ◽  
Roman Frątczak ◽  
Ewa Zawiślak
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Rapid Maxillary Expansion ◽  
Stress Distributions ◽  
Maxillary Expansion ◽  
Facial Skeleton ◽  
Element Analysis ◽  
Maxillary Constriction

The aim of this study was to compare the reduced stresses according to Huber’s hypothesis and the displacement pattern in the region of the facial skeleton using a tooth- or bone-borne appliance in surgically assisted rapid maxillary expansion (SARME). In the current literature, the lack of updated reports about biomechanical effects in bone-borne appliances used in SARME is noticeable. Finite element analysis (FEA) was used for this study. Six facial skeleton models were created, five with various variants of osteotomy and one without osteotomy. Two different appliances for maxillary expansion were used for each model. The three-dimensional (3D) model of the facial skeleton was created on the basis of spiral computed tomography (CT) scans of a 32-year-old patient with maxillary constriction. The finite element model was built using ANSYS 15.0 software, in which the computations were carried out. Stress distributions and displacement values along the 3D axes were found for each osteotomy variant with the expansion of the tooth- and the bone-borne devices at a level of 0.5 mm. The investigation showed that in the case of a full osteotomy of the maxilla, as described by Bell and Epker in 1976, the method of fixing the appliance for maxillary expansion had no impact on the distribution of the reduced stresses according to Huber’s hypothesis in the facial skeleton. In the case of the bone-borne appliance, the load on the teeth, which may lead to periodontal and orthodontic complications, was eliminated. In the case of a full osteotomy of the maxilla, displacements in the buccolingual direction for all the variables of the bone-borne appliance were slightly bigger than for the tooth-borne appliance.

Finite Element Analysis and Optimization of Long-Span Gantry NC Machining Center Structure

2011 ◽  
Vol 346 ◽  
pp. 379-384
Author(s):  
Shu Bo Xu ◽  
Yang Xi ◽  
Cai Nian Jing ◽  
Ke Ke Sun
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Design Method ◽  
Dynamic Performance ◽  
Plate Thickness ◽  
Element Model ◽  
Wall Structure ◽  
Characteristic Analysis ◽  
Element Analysis ◽  
Dynamic Performance Analysis

The use of finite element theory and modal analysis theory, the structure of the machine static and dynamic performance analysis and prediction using optimal design method for optimization, the new machine to improve job performance, improve processing accuracy, shorten the development cycle and enhance the competitiveness of products is very important. Selected for three-dimensional CAD modeling software-UG NX4.0 and finite element analysis software-ANSYS to set up the structure of the beam finite element model, and then post on the overall structure of the static and dynamic characteristic analysis, on the basis of optimized static and dynamic performance is more superior double wall structure of the beam. And by changing the wall thickness and the thickness of the inner wall, as well as the reinforcement plate thickness overall sensitivity analysis shows that changes in these three parameters on the dynamic characteristics of post impact. Application of topology optimization methods, determine the optimal structure of the beam ultimately.

scholarly journals Analysis for Wrinkling Behavior of Girth-Welded Line Pipe

1996 ◽  
Author(s):  
Luiz T. Souza ◽  
David W. Murray
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Finite Element Model ◽  
Internal Pressure ◽  
Experimental Test ◽  
Element Model ◽  
Element Analysis ◽  
Line Pipe ◽  
New Era ◽  
Analytical Tools

The paper presents results for finite element analysis of full-sized girth-welded specimens of line pipe and compares these results with the behavior exhibited by test specimens subjected to constant axial force, internal pressure and monotonically increasing curvatures. Recommendations for the ‘best’ type of analytical finite element model are given. Comparisons between the behavior predicted analytically and the observed behavior of the experimental test specimens are made. The mechanism of wrinkling is explained and the evolution of the deformed configurations for different wrinkling modes is examined. It is concluded that the analytical tools now available are sufficiently reliable to predict the behavior of pipe in a manner that was not previously possible and that this should create a new era for the design and assessment of pipelines if the technology is properly exploited by industry.

FINITE ELEMENT ANALYSIS OF A DENTAL IMPLANT

2003 ◽  
Vol 15 (02) ◽  
pp. 82-85 ◽  
Author(s):  
SHYH-CHOUR HUANG ◽  
CHANG-FENG TSAI
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Element Model ◽  
Element Analysis ◽  
3 Dimensional ◽  
Dimensional Finite Element ◽  
The Stability ◽  
Stress Concentration Effect ◽  
Implant System

This paper presents results from using a 3-dimensional finite element model to assess the stress distribution in the bone, in the implant and in the abutment as a function of the implant's diameter and length. Increasing implant diameter and length increases the stability of the implant system. By using a finite element analysis, we show that implant length does not decrease the stress distribution of either the implant or the bone. Alternatively, however implant diameter increases reduce the stresses. For the latter case, the contact area between implant and bone is increased thus the stress concentration effect is decreased. Also, with increased implant diameter the bone loss is decreased and as a consequence the success rate is improved.

Finite Element Analysis of Tandem Rubber O-Ring Sealing Structure at the End of Shaft

2013 ◽  
Vol 774-776 ◽  
pp. 25-29
Author(s):  
Cong Fang Hu ◽  
Yuan Qiang Tan
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Finite Element Model ◽  
Element Model ◽  
Compression Rate ◽  
Element Analysis ◽  
Uniform Compression ◽  
Friction Factors ◽  
Sealing Performance ◽  
Sealing Failure

Based on the tandem sealing structure at the end of the shaft,a finite element model of rubber O-rings has been established and the sealing performance of rubber O-ring has been analyzed. There is an un-uniform compression among these O-rings which lead to the sealing failure. Under different friction factors, several groups of the rubber O-rings have been analyzed, finding that the friction factor is the reason of un-uniform compression. The effect of different average compression rate has been investigated, which has been integrated in the sealing criteria for the tandem O-rings, providing a reference for the optimization of tandem sealing structure at the end of the shaft. According to the sealing criteria for a single O-ring, the sealing criteria for the tandem O-rings is built.

Finite Element Analysis for the Crankshaft of the Piston Compressor

2010 ◽  
Vol 102-104 ◽  
pp. 17-21
Author(s):  
Bin Zhao
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Natural Frequencies ◽  
Piston Compressor ◽  
Element Model ◽  
Ansys Software ◽  
Element Analysis ◽  
Rotating Speed ◽  
Dynamical Characteristics ◽  
The Finite Element Model

In order to study the static and dynamical characteristics of the crankshaft, ANSYS software was used to carry out the corresponding calculations. The entity model of the crankshaft was established by UG software firstly, and then was imported into ANSYS software for meshing, and then the finite element model of the crankshaft was constructed. The crankshaft satisfied the requirement of stiffness and strength through static analysis. The top six natural frequencies and corresponding shapes were acquired through modal analysis, and the every order critical rotating speed of the crankshaft was calculated. The fatigue life of the crank was calculated by fatigue module of ANSYS software finally. These results offered the theoretical guidance for designing, manufacturing and repairing the crankshaft.

Sign in / Sign up

Export Citation Format

Share Document