scholarly journals Film Cooling Effectiveness and Heat/Mass Transfer Coefficient Measurement Around a Conical-Shaped Hole With a Compound Angle Injection

1999 ◽  
Author(s):  
H. H. Cho ◽  
D. H. Rhee ◽  
B. G. Kim
Keyword(s):  
Mass Transfer ◽  
Film Cooling ◽  
Heat Mass Transfer ◽  
Transfer Coefficients ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Hole ◽  
Shaped Hole ◽  
Hole Geometry ◽  
Compound Angle

The present study investigates local film cooling effectiveness values and heat/mass transfer coefficients around a conical-shaped film cooling hole with compound angle orientations. Three types of film cooling hole geometry are compared in this study; one is cylindrical hole geometry with constant cross section and the others are shaped hole geometries with conically-enlarged hole exits. The shaped holes have cylindrical passage sections at the hole inlet region to obtain a certain pressure drop through the holes. One shaped hole expands 4° in all directions from the middle of hole to the exit. The other shaped hole has the tilted center-line by 4° between the conical and metering holes and is enlarged by 8° to downstream side. The hole area ratios of the exit to the inlet are 2.55 and 2.48, respectively. The compound-angled film cooling jet is ejected through the single holes, which are inclined at 30° to the surface based on the metering hole and are rotatable in lateral direction from 0° to 90°. The blowing rates are changed from 0.5 to 2.0. The naphthalene sublimation technique is used to determine local heat/mass transfer coefficients and local adiabatic/impermeable wall film cooling effectiveness around the injection hole. The results indicate that the injected jet protects the surface effectively with low blowing rates and spreads more widely with the compound angle injections than the axial injection. For the shaped hole enlarged by 4° in all directions, the penetration of jet is reduced and higher cooling performance is obtained even at relatively high blowing rates because the increased hole exit area reduces hole exit velocity. Furthermore, the film cooling effectiveness is fairly uniform near the hole due to the wide lateral spreading of coolant with the expanded cooling hole exit.

Film Cooling Downstream of a Row of Discrete Holes With Compound Angle

2000 ◽  
Vol 123 (2) ◽  
pp. 222-230 ◽  
Author(s):  
R. J. Goldstein ◽  
P. Jin
Keyword(s):  
Mass Transfer ◽  
Transfer Coefficient ◽  
Mass Transfer Coefficient ◽  
Film Cooling ◽  
Transfer Coefficients ◽  
Cooling Effectiveness ◽  
Mass Transfer Coefficients ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Compound Angle

A special naphthalene sublimation technique is used to study the film cooling performance downstream of one row of holes of 35 deg inclination angle and 45 deg compound angle with 3d hole spacing and relatively small hole length to diameter ratio (6.3). Both film cooling effectiveness and mass/heat transfer coefficients are determined for blowing rates from 0.5 to 2.0 with density ratio of unity. The mass transfer coefficient is measured using pure air film injection, while the film cooling effectiveness is derived from comparison of mass transfer coefficients obtained following injection of naphthalene-vapor-saturated air with that of pure air injection. This technique enables one to obtain detailed local information on film cooling performance. General agreement is found in local film cooling effectiveness when compared with previous experiments. The laterally averaged effectiveness with compound angle injection is higher than that with inclined holes immediately downstream of injection at a blowing rate of 0.5 and is higher at all locations downstream of injection at larger blowing rates. A large variation of mass transfer coefficients in the lateral direction is observed in the present study. At low blowing rates of 0.5 and 1.0, the laterally averaged mass transfer coefficient is close to that of injection without compound angle. At the highest blowing rate used (2.0), the asymmetric vortex motion under the jets increases the mass transfer coefficient drastically ten diameters downstream of injection.

Heat (Mass) Transfer and Film Cooling Effectiveness With Injection Through Discrete Holes: Part II—On the Exposed Surface

1995 ◽  
Vol 117 (3) ◽  
pp. 451-460 ◽  
Author(s):  
H. H. Cho ◽  
R. J. Goldstein
Keyword(s):  
Mass Transfer ◽  
Film Cooling ◽  
Heat Mass Transfer ◽  
Saturated Vapor ◽  
Back Surface ◽  
Exposed Surface ◽  
Transfer Coefficients ◽  
Lateral Direction ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness

The heat (mass) transfer coefficient and the film cooling effectiveness are obtained from separate tests using pure air and naphthalene-saturated vapor injected through circular holes into a crossflow of air. The experiments indicate that Sherwood numbers around the injection hole are up to four times those on a flat plate (without injection holes) due to the interaction of the jets and the mainstream. The mass transfer around the injection holes is dominated by formations of horseshoe, side, and kidney vortices, which are generated by the jet and crossflow interaction. For an in-line array of holes, the effectiveness is high and uniform in the streamwise direction but has a large variation in the lateral direction. The key parameters, including transfer coefficients on the back surface (Part I), inside the hole (Part I), and on the exposed surfaces, and the effectiveness on the exposed surface, are obtained so that the wall temperature distribution near the injection holes can be determined for a given heat flux condition. This detailed information will also aid the numerical modeling of flow and mass/heat transfer around film cooling holes.

Film Cooling Downstream of a Row of Discrete Holes With Compound Angle

2000 ◽  
Author(s):  
R. J. Goldstein ◽  
P. Jin
Keyword(s):  
Mass Transfer ◽  
Transfer Coefficient ◽  
Mass Transfer Coefficient ◽  
Film Cooling ◽  
Transfer Coefficients ◽  
Cooling Effectiveness ◽  
Mass Transfer Coefficients ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Compound Angle

A special naphthalene sublimation technique is used to study the film cooling performance downstream of one row of holes of 35° inclination angle and 45° compound angle with 3 diameter hole spacing and relatively small hole length to diameter ratio (6.3). Both film cooling effectiveness and mass/heat transfer coefficients are determined for blowing rates from 0.5 to 2.0 with density ratio of unity. The mass transfer coefficient is measured using pure air film injection, while the film cooling effectiveness is derived from comparison of mass transfer coefficients obtained following injection of naphthalene-vapor-saturated air with that of pure air injection. This technique enables one to obtain detailed local information on film cooling performance. General agreement is found in local film cooling effectiveness when compared with previous experiments. The laterally-averaged effectiveness with compound angle injection is higher than that with inclined holes immediately downstream of injection at a blowing rate of 0.5 and is higher at all locations downstream of injection at larger blowing rates. A large variation of mass transfer coefficients in the lateral direction is observed in the present study. At low blowing rates of 0.5 and 1.0, the laterally-averaged mass transfer coefficient is close to that of injection without compound angle. At the highest blowing rate used (2.0), the asymmetrical vortex motion under the jets increases the mass transfer coefficient drastically ten diameters downstream of injection.

Assessment of a Double Hole Film Cooling Geometry Using S-PIV and PSP

2013 ◽  
Author(s):  
Lesley M. Wright ◽  
Stephen T. McClain ◽  
Charles P. Brown ◽  
Weston V. Harmon
Keyword(s):  
Film Cooling ◽  
Density Ratio ◽  
Three Dimensional ◽  
Field Measurements ◽  
Secondary Flows ◽  
Cylindrical Hole ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Hole Geometry ◽  
Compound Angle

A novel, double hole film cooling configuration is investigated as an alternative to traditional cylindrical and fanshaped, laidback holes. This experimental investigation utilizes a Stereo-Particle Image Velocimetry (S-PIV) to quantitatively assess the ability of the proposed, double hole geometry to weaken or mitigate the counter-rotating vortices formed within the jet structure. The three-dimensional flow field measurements are combined with surface film cooling effectiveness measurements obtained using Pressure Sensitive Paint (PSP). The double hole geometry consists of two compound angle holes. The inclination of each hole is θ = 35°, and the compound angle of the holes is β = ± 45° (with the holes angled toward one another). The simple angle cylindrical and shaped holes both have an inclination angle of θ = 35°. The blowing ratio is varied from M = 0.5 to 1.5 for all three film cooling geometries while the density ratio is maintained at DR = 1.0. Time averaged velocity distributions are obtained for both the mainstream and coolant flows at five streamwise planes across the fluid domain (x/d = −4, 0, 1, 5, and 10). These transverse velocity distributions are combined with the detailed film cooling effectiveness distributions on the surface to evaluate the proposed double hole configuration (compared to the traditional hole designs). The fanshaped, laidback geometry effectively reduces the strength of the kidney-shaped vortices within the structure of the jet (over the entire range of blowing ratios considered). The three-dimensional velocity field measurements indicate the secondary flows formed from the double hole geometry strengthen in the plane perpendicular to the mainstream flow. At the exit of the double hole geometry, the streamwise momentum of the jets is reduced (compared to the single, cylindrical hole), and the geometry offers improved film cooling coverage. However, moving downstream in the steamwise direction, the two jets form a single jet, and the counter-rotating vortices are comparable to those formed within the jet from a single, cylindrical hole. These strong secondary flows lift the coolant off the surface, and the film cooling coverage offered by the double hole geometry is reduced.

Investigations of improved cooling effectiveness for ramp film cooling with compound angle film cooling jets

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Krishna Anand Vasu Devan Nair Girija Kumari ◽  
Parammasivam Kanjikoil Mahali
Keyword(s):  
Film Cooling ◽  
Flat Surface ◽  
Flow Characteristics ◽  
Test Surface ◽  
Cooling Effectiveness ◽  
Content Type ◽  
Film Cooling Effectiveness ◽  
Ramp Test ◽  
Cooling Hole ◽  
Compound Angle

Purpose This paper aims to investigate the film cooling effectiveness (FCE) and mixing flow characteristics of the flat surface ramp model integrated with a compound angled film cooling jet. Design/methodology/approach Three-dimensional numerical simulation is performed on a flat surface ramp model with Reynolds Averaged Navier-Stokes approach using a finite volume solver. The tested model has a fixed ramp angle of 24° and a ramp width of two times the diameter of the film cooling hole. The coolant air is injected at 30° along the freestream direction. Three different film hole compound angles oriented to freestream direction at 0°, 90° and 180° were investigated for their performance on-ramp film cooling. The tested blowing ratios (BRs) are in the range of 0.9–2.0. Findings The film hole oriented at a compound angle of 180° has improved the area-averaged FCE on the ramp test surface by 86.74% at a mid-BR of 1.4% and 318.75% at higher BRs of 2.0. The 180° film hole compound angle has also produced higher local and spanwise averaged FCE on the ramp test surface. Originality/value According to the authors’ knowledge, this study is the first of its kind to investigate the ramp film cooling with a compound angle film cooling hole. The improved ramp model with a 180° film hole compound angle can be effectively applied for the end-wall surfaces of gas turbine film cooling.

Influence of Coolant Density on Turbine Blade Film-Cooling With Compound-Angle Shaped Holes

2012 ◽  
Author(s):  
Kevin Liu ◽  
Shang-Feng Yang ◽  
Je-Chin Han
Keyword(s):  
Film Cooling ◽  
Momentum Flux ◽  
Density Ratio ◽  
Flux Ratio ◽  
Suction Side ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Shaped Hole ◽  
Compound Angle

Adiabatic film-cooling effectiveness is examined systematically on a typical high pressure turbine blade by varying three critical flow parameters: coolant blowing ratio, coolant-to-mainstream density ratio, and freestream turbulence intensity. Three average coolant blowing ratios 1.0, 1.5, and 2.0; three coolant density ratios 1.0, 1.5, and 2.0; two turbulence intensities 4.2% and 10.5%, are chosen for this study. Conduction-free pressure sensitive paint (PSP) technique is used to measure film-cooling effectiveness. Three foreign gases — N2 for low density, CO2 for medium density, and a mixture of SF6 and Argon for high density are selected to study the effect of coolant density. The test blade features 45° compound-angle shaped holes on the suction side and pressure side, and 3 rows of 30° radial-angle cylindrical holes around the leading edge region. The inlet and the exit Mach number are 0.27 and 0.44, respectively. Reynolds number based on the exit velocity and blade axial chord length is 750,000. Results reveal that the PSP is a powerful technique capable of producing clear and detailed film effectiveness contours with diverse foreign gases. As blowing ratio exceeds the optimum value, it induces more mixing of coolant and mainstream. Thus film-cooling effectiveness reduces. Greater coolant-to-mainstream density ratio results in lower coolant-to-mainstream momentum and prevents coolant to lift-off; as a result, film-cooling increases. Higher freestream turbulence causes effectiveness to drop everywhere except in the region downstream of suction side. Results are also correlated with momentum flux ratio and compared with previous studies. It shows that compound shaped hole has the greatest optimum momentum flux ratio, and then followed by axial shaped hole, compound cylindrical hole, and axial cylindrical hole.

Film Cooling Effectiveness and Mass/Heat Transfer Coefficient Downstream of One Row of Discrete Holes

1999 ◽  
Vol 121 (2) ◽  
pp. 225-232 ◽  
Author(s):  
R. J. Goldstein ◽  
P. Jin ◽  
R. L. Olson
Keyword(s):  
Heat Transfer ◽  
Mass Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Density Ratio ◽  
Transfer Coefficients ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness

A special naphthalene sublimation technique is used to study the film cooling performance downstream of one row of holes of 35 deg inclination angle with 3d hole spacing and relatively small hole length to diameter ratio (L/d = 6.3). Both film cooling effectiveness and mass/heat transfer coefficient are determined for blowing rates from 0.5 to 2.0 with density ratio of 1.0. The mass transfer coefficient is measured using pure air film injection, while the film cooling effectiveness is derived from comparison of mass transfer coefficients obtained following injection of naphthalene-vapor-saturated air with those from pure air injection. This technique enables one to obtain detailed local information on film cooling performance. The laterally averaged and local film cooling effectiveness agree with previous experiments. The difference between mass/heat transfer coefficients and previous heat transfer results indicates that conduction error may play an important role in the earlier heat transfer measurements.

Experimental and Numerical Film Effectiveness Downstream a Row of Compound Angle Film Holes

2003 ◽  
Author(s):  
A. Khanicheh ◽  
M. E. Taslim
Keyword(s):  
High Temperature ◽  
Film Cooling ◽  
Computational Study ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Single Row ◽  
Cooling Hole ◽  
Cylindrical Holes ◽  
Film Cooling Holes ◽  
Compound Angle

High component lifetimes of modern gas turbines can be achieved by cooling the airfoils effectively. Film cooling is commonly employed on the airfoils and other engine hot section surfaces in order to protect them from the high thermal stress fields created by exposure to combustion gases. Complex geometries as well as optimized cooling considerations often dictate the use of compound-angled film cooling hole. In the present experimental and computational study, the effects that two different compound angle film cooling hole injection configurations have on film cooling effectiveness are investigated. Film cooling effectiveness measurements have been made downstream of a single row of compound angle cylindrical holes with a diameter of 7.5 mm, and a single row of compound angle, diffuser-shaped holes with an inlet diameter of 7.5 mm. The cylindrical holes were inclined (α=25°) with respect to the coverage surface and were oriented perpendicular to the high-temperature airflow direction. The diffuser-shaped holes had a compound angle of 45 degrees with respect to the high temperature air flow direction and, similar to the cylindrical film holes, a 25-deg angle with the coverage surface. Both geometries were tested over a blowing ratio range of 0.7 to 4.0. Surface temperatures were measured along four longitudinal rows of thermocouples covering the downstream area between two adjacent holes. The results showed that the best overall protection over the widest range of blowing ratios was provided by the diffuser-shaped film cooling holes. Compared with the cylindrical hole results, the diffuser-shaped expansion holes produced higher film cooling effectiveness downstream of the film cooling holes, particularly at high blowing ratios. The increased cross sectional area at the shaped hole exit compared to that of the cylindrical hole lead to a reduction of the mean velocity, thus the reduction of the momentum flux of the jet exiting the hole. Therefore, the penetration of the jet into the main flow was reduced, resulting in an increased cooling effectiveness. A commercially available CFD software package was used to study film cooling effectiveness downstream of the row of holes. Comparisons between the experimentally measured and numerically calculated film effectiveness distributions showed that the computed results are in reasonable agreement with the measured results. Therefore, CFD can be considered as a viable tool to predict the cooling performance of different film cooling configurations in a parametric study. A more realistic turbulence model, possibly adopting a two-layer model that incorporates boundary layer anisotropy, in the computational study may improve the predicted results.

Effect of Upstream Step on Flat Plate Film-Cooling Effectiveness Using PSP

2011 ◽  
Vol 133 (4) ◽  
Author(s):  
Akhilesh P. Rallabandi ◽  
Joshua Grizzle ◽  
Je-Chin Han
Keyword(s):  
Film Cooling ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Axial Angle ◽  
Step Effect ◽  
Cooling Hole ◽  
Cylindrical Holes ◽  
Film Cooling Holes ◽  
Compound Angle ◽  
State Pressure

The effect of a step positioned upstream of a row of film-cooling holes on the film-cooling effectiveness is studied systematically using the steady state pressure sensitive paint technique. The upstream step effect is studied on four separate hole geometries: simple angled (axial angle of 30 deg) and compound angled (axial angle of 30 deg and compound angle of 45 deg) and cylindrical and fan-shaped film-cooling holes. Each plate considered has seven holes, each hole 4 mm in diameter. The plates with cylindrical holes have a spacing of 3 diameters (12 mm) between the centers of two consecutive holes while the fan-shaped holes have a spacing of 3.75 diameters (15 mm). Three different step heights (12.5%d, 25%d, and 37.5%d) are studied. The effect of the width of the step is also studied; the distance of the step upstream of the hole and the positioning of the step downstream of the film-cooling hole. Four separate blowing ratios are reported for all tests: M=0.3, M=0.6, M=1.0, and M=1.5. All studies have been conducted with a mainstream of 25 m/s velocity at an ambient temperature of 22°C. Results indicate an increase in film-cooling effectiveness in the region near the hole due to the upstream step for all the plates considered. This increase due to the step is found to be most significant in the case of compound angled cylindrical holes and least significant in the case of simple angled fan-shaped holes.

Sign in / Sign up

Export Citation Format

Share Document