Influence of Turbulence Intensity on Annular Turbine Stator Aerodynamics at Low Reynolds Numbers

1999 ◽  
Author(s):  
Takayuki Matsunuma ◽  
Hiroyuki Abe ◽  
Yasukata Tsutsui
Keyword(s):  
Reynolds Number ◽  
Turbulence Intensity ◽  
Gas Turbines ◽  
Separation Zone ◽  
Reynolds Numbers ◽  
Pressure Probe ◽  
Single Element ◽  
Low Reynolds Numbers ◽  
Turbine Stator ◽  
Low Reynolds

The aerodynamic characteristics of turbine cascades are thought to be relatively satisfactory due to the favorable pressure of the accelerating flow. But within the low Reynolds number region of 6×104 where the 300kW ceramic gas turbines which are being developed under the New Sunshine project of Japan operate, the characteristics such as boundary layer separation, reattachment and secondary flow which lead to prominent power losses can not be easily predicted. In this research, experiments have been conducted to evaluate the performance of an annular turbine stator cascade, especially focused on the influence of inlet turbulence intensity at low Reynolds numbers. The Reynolds number, based on inlet condition, was varied from 2×104 to 12×104. The turbulence intensity was changed between 0.5% and 8.9% by setting turbulence generation sheets. The wake of the cascade was measured using a 5-hole pressure probe and a single element hot-wire anemometry. The Reynolds number was a determinative important parameter, while the turbulence intensity was found to have an insignificant effect on the overall total pressure loss of annular turbine stator at low Reynolds numbers. However, the increase in separation zone on suction surface and the decrease of passage vortices near the endwalls were observed locally with the increase in the inlet turbulence intensity. Instantaneous velocity signals proved the transformation of the flow structure in separation zone. The increase in profile loss (separation) and the decrease in net secondary loss (passage vonices) offset each other. Therefore, the net overall loss remains almost constant.

Measurements in a Turbine Cascade Flow Under Ultra Low Reynolds Number Conditions

2001 ◽  
Vol 124 (1) ◽  
pp. 100-106 ◽  
Author(s):  
Kenneth W. Van Treuren ◽  
Terrence Simon ◽  
Marc von Koller ◽  
Aaron R. Byerley ◽  
James W. Baughn ◽  
...  
Keyword(s):  
Reynolds Number ◽  
Turbulence Intensity ◽  
Free Stream ◽  
Reynolds Numbers ◽  
Vortex Generators ◽  
Separation Region ◽  
Suction Surface ◽  
Low Reynolds Numbers ◽  
Free Stream Turbulence ◽  
Low Reynolds

With the new generation of gas turbine engines, low Reynolds number flows have become increasingly important. Designers must properly account for transition from laminar to turbulent flow and separation of the flow from the suction surface, which is strongly dependent upon transition. Of interest to industry are Reynolds numbers based upon suction surface length and flow exit velocity below 150,000 and as low as 25,000. In this paper, the extreme low end of this Reynolds number range is documented by way of pressure distributions, loss coefficients, and identification of separation zones. Reynolds numbers of 25,000 and 50,000 and with 1 percent and 8-9 percent turbulence intensity of the approach flow (free-stream turbulence intensity, FSTI) were investigated. At 25,000 Reynolds number and low FSTI, the suction surface displayed a strong and steady separation region. Raising the turbulence intensity resulted in a very unsteady separation region of nearly the same size on the suction surface. Vortex generators were added to the suction surface, but they appeared to do very little at this Reynolds number. At the higher Reynolds number of 50,000, the low-FSTI case was strongly separated on the downstream portion of the suction surface. The separation zone was eliminated when the turbulence level was increased to 8-9 percent. Vortex generators were added to the suction surface of the low-FSTI case. In this instance, the vortices were able to provide the mixing needed to re-establish flow attachment. This paper shows that massive separation at very low Reynolds numbers (25,000) is persistent, in spite of elevated FSTI and added vortices. However, at a higher Reynolds number, there is opportunity for flow reattachment either with elevated free-stream turbulence or with added vortices. This may be the first documentation of flow behavior at such low Reynolds numbers. Although it is undesirable to operate under these conditions, it is important to know what to expect and how performance may be improved if such conditions are unavoidable.

scholarly journals Characteristics of an Annular Turbine Cascade at Low Reynolds Numbers

1998 ◽  
Author(s):  
Takayuki Matsunuma ◽  
Hiroyuki Abe ◽  
Yasukata Tsutsui ◽  
Koji Murata
Keyword(s):  
Reynolds Number ◽  
Gas Turbines ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Boundary Layer Separation ◽  
Aerodynamic Characteristics ◽  
Secondary Flows ◽  
Suction Surface ◽  
Low Reynolds Numbers ◽  
Low Reynolds

The aerodynamic characteristics of turbine cascades are thought to be relatively satisfactory due to the favorable pressure gradient of the accelerating flow. But within the low Reynolds number region of approximately 6×104 where the 300kW ceramic gas turbines which are being developed under the New Sunshine Project of Japan operate, the characteristics such as boundary layer separation, reattachment and secondary flow which lead to prominent power losses can not be easily predicted. In this research, experiments have been conducted to evaluate the performance of an annular turbine stator cascade. Wakes of the cascade were measured using a single hot wire and five hole pressure tube, for a range of blade chord Reynolds numbers based on the inlet condition from 2×104 to 12×104. Flow visualizations on the suction surface of the blade were carried out using oil film method. At low Reynolds numbers, the flow structure in the annular cascade was quite complex and three-dimensional. The separation line on the suction surface moved upstream due to the decrease of Reynolds number. In addition, the growth of secondary flows, i.e., passage vortices and leakage vortex, was extremely under the influence of Reynolds number.

scholarly journals Aerodynamic Characteristics of Different Airfoils under Varied Turbulence Intensities at Low Reynolds Numbers

2020 ◽  
Vol 10 (5) ◽  
pp. 1706 ◽  
Author(s):  
Yang Zhang ◽  
Zhou Zhou ◽  
Kelei Wang ◽  
Xu Li
Keyword(s):  
Reynolds Number ◽  
Turbulence Intensity ◽  
Flow Separation ◽  
Numerical Study ◽  
Reynolds Numbers ◽  
Jet Flow ◽  
Aerodynamic Characteristics ◽  
Aerodynamic Performance ◽  
Low Reynolds Numbers ◽  
Low Reynolds

A numerical study was conducted on the influence of turbulence intensity and Reynolds number on the mean topology and transition characteristics of flow separation to provide better understanding of the unsteady jet flow of turboelectric distributed propulsion (TeDP) aircraft. By solving unsteady Reynolds averaged Navier-Stokes (URANS) equation based on C-type structural mesh and γ - Re ˜ θ t transition model, the aerodynamic characteristics of the NACA0012 airfoil at different turbulence intensities was calculated and compared with the experimental results, which verifies the reliability of the numerical method. Then, the effects of varied low Reynolds numbers and turbulence intensities on the aerodynamic performance of NACA0012 and SD7037 were investigated. The results show that higher turbulence intensity or Reynolds number leads to more stable airfoil aerodynamic performance, larger stalling angle, and earlier transition with a different mechanism. The generation and evolution of the laminar separation bubble (LSB) are closely related to Reynolds number, and it would change the effective shape of the airfoil, having a big influence on the airfoil’s aerodynamic characteristics. Compared with the symmetrical airfoil, the low-Reynolds-number airfoil can delay the occurrence of flow separation and produce more lift in the same conditions, which provides guidance for further airfoil design under TeDP jet flow.

Measurements in a Turbine Cascade Flow Under Ultra Low Reynolds Number Conditions

2001 ◽  
Author(s):  
Kenneth W. Van Treuren ◽  
Terrence Simon ◽  
Marc von Koller ◽  
Aaron R. Byerley ◽  
James W. Baughn ◽  
...  
Keyword(s):  
Reynolds Number ◽  
Turbulence Intensity ◽  
Low Reynolds Number ◽  
Reynolds Numbers ◽  
Vortex Generators ◽  
Separation Region ◽  
Suction Surface ◽  
Number Range ◽  
Low Reynolds Numbers ◽  
Low Reynolds

With the new generation of gas turbine engines, low Reynolds number flows have become increasingly important. Designers must properly account for transition from laminar to turbulent flow and separation of the flow from the suction surface, which is strongly dependent upon transition. Of interest to industry are Reynolds numbers based upon suction surface length and flow exit velocity below 150,000 and as low as 25,000. In this paper, the extreme low end of this Reynolds number range is documented by way of pressure distributions, loss coefficients and identification of separation zones. Reynolds numbers of 25,000 and 50,000 and with 1% and 8–9% turbulence intensity of the approach flow (Free Stream Turbulence Intensity, FSTI) were investigated. At 25,000 Reynolds number and low FSTI, the suction surface displayed a strong and steady separation region. Raising the turbulence intensity resulted in a very unsteady separation region of nearly the same size on the suction surface. Vortex generators were added to the suction surface, but they appeared to do very little at this Reynolds number. At the higher Reynolds number of 50,000, the low-FSTI case was strongly separated on the downstream portion of the suction surface. The separation zone was eliminated when the turbulence level was increased to 8–9%. Vortex generators were added to the suction surface of the low-FSTI case. In this instance, the vortices were able to provide the mixing needed to reestablish flow attachment. This paper shows that massive separation at very low Reynolds numbers (25,000) is persistent, in spite of elevated FSTI and added vortices. However, at a higher Reynolds number, there is opportunity for flow reattachment either with elevated freestream turbulence or with added vortices. This may be the first documentation of flow behavior at such low Reynolds numbers. Though undesirable to operate under these conditions, it is important to know what to expect and how performance may be improved if such conditions are unavoidable.

Low Reynolds number flow around and heat transfer from a heated circular cylinder

2010 ◽  
Vol 1 (1-2) ◽  
pp. 15-20 ◽  
Author(s):  
B. Bolló
Keyword(s):  
Reynolds Number ◽  
Circular Cylinder ◽  
Lift Coefficient ◽  
Reynolds Numbers ◽  
Low Reynolds Numbers ◽  
Reynolds Number Flow ◽  
Two Dimensional Flow ◽  
Number Flow ◽  
Low Reynolds ◽  
Increasing Temperature

Abstract The two-dimensional flow around a stationary heated circular cylinder at low Reynolds numbers of 50 < Re < 210 is investigated numerically using the FLUENT commercial software package. The dimensionless vortex shedding frequency (St) reduces with increasing temperature at a given Reynolds number. The effective temperature concept was used and St-Re data were successfully transformed to the St-Reeff curve. Comparisons include root-mean-square values of the lift coefficient and Nusselt number. The results agree well with available data in the literature.

Occurrence of Bubbles in a Thin Wire at Low Reynolds Number

1992 ◽  
Vol 114 (2) ◽  
pp. 255-260 ◽  
Author(s):  
K. Sato
Keyword(s):  
Separation Zone ◽  
Reynolds Numbers ◽  
Cavitation Number ◽  
The Other ◽  
Laminar Separation ◽  
Low Reynolds Numbers ◽  
Thin Wires ◽  
Different Types ◽  
Low Reynolds ◽  
Air Diffusion

Thin wires of various diameters from 0.07 to 0.7 mm are examined about appearances and characteristics of bubble occurrence behind them in the range of low Reynolds numbers. The appearance of bubbles is very dependent on diameters of wires. Two different types of bubbles can be observed in the present experiment. One is a streamer-type bubble for smaller wires and the other is a small unspherical bubble for larger wires. The incipient and the desinent values of cavitation number also change greatly with the bubble types. The streamer-type bubble is related to the presence of laminar separation zone and the growth due to air diffusion. The small unspherical bubble can be mainly attributed to the motion of rolled-up vortices and the growth due to vaporization.

A Computational Study on Airfoils at a Low Reynolds Number

2000 ◽  
Author(s):  
Ajit Pal Singh ◽  
S. H. Winoto ◽  
D. A. Shah ◽  
K. G. Lim ◽  
Robert E. K. Goh
Keyword(s):  
Reynolds Number ◽  
Computational Analysis ◽  
Computational Study ◽  
Low Reynolds Number ◽  
Micro Air Vehicles ◽  
Reynolds Numbers ◽  
Aerodynamic Performance ◽  
Low Reynolds Numbers ◽  
Study Results ◽  
Low Reynolds

Abstract Performance characteristics of some low Reynolds number airfoils for the use in micro air vehicles (MAVs) are computationally studied using XFOIL at a Reynolds number of 80,000. XFOIL, which is based on linear-vorticity stream function panel method coupled with a viscous integral formulation, is used for the analysis. In the first part of the study, results obtained from the XFOIL have been compared with available experimental data at low Reynolds numbers. XFOIL is then used to study relative aerodynamic performance of nine different airfoils. The computational analysis has shown that the S1223 airfoil has a relatively better performance than other airfoils considered for the analysis.

An Experimental Investigation of the Effect of Freestream Turbulence on the Wake of a Separated Low-Pressure Turbine Blade at Low Reynolds Numbers

1999 ◽  
Vol 122 (2) ◽  
pp. 431-433 ◽  
Author(s):  
C. G. Murawski ◽  
K. Vafai
Keyword(s):  
Reynolds Number ◽  
Turbine Blade ◽  
Turbulence Intensity ◽  
Reynolds Numbers ◽  
Low Pressure ◽  
Freestream Turbulence ◽  
Suction Surface ◽  
Low Reynolds Numbers ◽  
Low Pressure Turbine ◽  
Flow Reynolds Number

An experimental study was conducted in a two-dimensional linear cascade, focusing on the suction surface of a low pressure turbine blade. Flow Reynolds numbers, based on exit velocity and suction length, have been varied from 50,000 to 300,000. The freestream turbulence intensity was varied from 1.1 to 8.1 percent. Separation was observed at all test Reynolds numbers. Increasing the flow Reynolds number, without changing freestream turbulence, resulted in a rearward movement of the onset of separation and shrinkage of the separation zone. Increasing the freestream turbulence intensity, without changing Reynolds number, resulted in shrinkage of the separation region on the suction surface. The influences on the blade’s wake from altering freestream turbulence and Reynolds number are also documented. It is shown that width of the wake and velocity defect rise with a decrease in either turbulence level or chord Reynolds number. [S0098-2202(00)00202-9]

Using Turbulence Intensity and Reynolds Number to Predict Flow Separation on a Highly Loaded, Low-Pressure Gas Turbine Blade at Low Reynolds Numbers

2018 ◽  
Author(s):  
Kenneth Van Treuren ◽  
Tyler Pharris ◽  
Olivia Hirst
Keyword(s):  
Reynolds Number ◽  
Gas Turbine ◽  
Turbine Blade ◽  
Turbulence Intensity ◽  
Flow Separation ◽  
Reynolds Numbers ◽  
Low Pressure ◽  
High Altitudes ◽  
Low Reynolds Numbers ◽  
Low Pressure Turbine

The low-pressure turbine has become more important in the last few decades because of the increased emphasis on higher overall pressure and bypass ratios. The desire is to increase blade loading to reduce blade counts and stages in the low-pressure turbine of a gas turbine engine. Increased turbine inlet temperatures for newer cycles results in higher temperatures in the low-pressure turbine, especially the latter stages, where cooling technologies are not used. These higher temperatures lead to higher work from the turbine and this, combined with the high loadings, can lead to flow separation. Separation is more likely in engines operating at high altitudes and reduced throttle setting. At the high Reynolds numbers found at takeoff, the flow over a low-pressure turbine blade tends to stay attached. At lower blade Reynolds numbers (25,000 to 200,000), found during cruise at high altitudes, the flow on the suction surface of the low-pressure turbine blades is inclined to separate. This paper is a study on the flow characteristics of the L1A turbine blade at three low Reynolds numbers (60,000, 108,000, and 165,000) and 15 turbulence intensities (1.89% to 19.87%) in a steady flow cascade wind tunnel. With this data, it is possible to examine the impact of Reynolds number and turbulence intensity on the location of the initiation of flow separation, the flow separation zone, and the reattachment location. Quantifying the change in separated flow as a result of varying Reynolds numbers and turbulence intensities will help to characterize the low momentum flow environments in which the low-pressure turbine must operate and how this might impact the operation of the engine. Based on the data presented, it is possible to predict the location and size of the separation as a function of both the Reynolds number and upstream freestream turbulence intensity (FSTI). Being able to predict this flow behavior can lead to more effective blade designs using either passive or active flow control to reduce or eliminate flow separation.

Sign in / Sign up

Export Citation Format

Share Document