Five Position Synthesis of Spherical (6, 7) Linkages

2008 ◽  
Author(s):  
Gim Song Soh ◽  
J. Michael McCarthy
Keyword(s):  
Design Problem ◽  
Degree Of Freedom ◽  
End Effector ◽  
Serial Chain ◽  
Design For All ◽  
Synthesis Procedure ◽  
Position Synthesis

This paper presents a geometric synthesis procedure for spherical (6, 7) linkages, often known as spherical six-bar linkages, based on adding two spherical RR constraints to a spherical 3R serial chain. The design can use the spherical 3R chain to shape the movement of the linkage and identify a set of task positions that shape the trajectory of the end-effector. We use five task positions to completely specify the two RR chains that constrain the system to one degree-of-freedom. This procedure yields spherical versions of the various topologies for the planar Watt and Stephenson six-bar linkages. We find that for any design problem we obtain at a minimum of two design candidates for the Watt-type linkage, and as many as 185 different design for all of the topologies obtained by constraining the spherical 3R chain. Wampler’s method for the analysis of spherical loops is used to analyze these linkages. An example design is presented in detail.

Seven-Position Synthesis of a Spatial Eight-Bar Linkage by Constraining a TRS Serial Chain

2009 ◽  
Author(s):  
Gim Song Soh ◽  
J. Michael McCarthy
Keyword(s):  
Degree Of Freedom ◽  
Upper Arm ◽  
End Effector ◽  
Serial Chain ◽  
Position Synthesis ◽  
Two Degree Of Freedom ◽  
Puma Robot

In this paper, we use seven-position synthesis to add four TS constraints to a TRS serial chain robot and obtain a two degree-of-freedom spatial eight-bar linkage. The TRS chain is an elbow manipulator, similar to a PUMA robot. We synthesize a TS dyad to connect the base of the robot to its forearm, and then we synthesize three TS dyads that connect the upper arm of the robot to its end-effector. The result is a two degree-of-freedom spatial eight-bar linkage that moves through seven prescribed positions. It consists of a TRST loop supporting a 3TS-RS platform, which we denote as a TS-TRS-3TS spatial linkage. We formulate and solve the design equations for the TS dyads, and analyze the resulting eight-bar linkage. An example demonstrates our results.

Dimensional Synthesis of Planar Eight-Bar Linkages Based on a Parallel Robot With a Prismatic Base Joint

2013 ◽  
Author(s):  
Gim Song Soh ◽  
Fangtian Ying
Keyword(s):  
Rigid Body ◽  
Design Process ◽  
Parallel Robot ◽  
Degree Of Freedom ◽  
Dimensional Synthesis ◽  
End Effector ◽  
Prismatic Joint ◽  
Serial Chain ◽  
Different Types

This paper details the dimensional synthesis for the rigid body guidance of planar eight-bar linkages that could be driven by a prismatic joint at its base. We show how two RR cranks can be added to a planar parallel robot formed by a PRR and 3R serial chain to guide its end-effector through a set of five task poses. This procedure is useful for designers who require the choice of ground pivot locations. The results are eight different types of one-degree of freedom planar eight-bar linkages. We demonstrate the design process with the design of a multifunctional wheelchair that could transform its structure between a self-propelled wheelchair and a walking guide.

A 7R-Based, Two Degrees of Freedom Robomech

2000 ◽  
Author(s):  
Ahmad A. Smaili
Keyword(s):  
Degrees Of Freedom ◽  
Parallel Architecture ◽  
Degree Of Freedom ◽  
Robot Arm ◽  
End Effector ◽  
Kinematic Constraints ◽  
Two Degrees Of Freedom ◽  
Synthesis Procedure ◽  
Two Degree Of Freedom

Abstract A robomech is a crossbreed of a mechanism and a robot arm. It has a parallel architecture equipped with more than one end effector to accomplish tasks that require the coordination of many functions. Robomechs with multi degrees of freedom that are based on the 4R and 5R chains have found their way into the literature. This article presents a new, two-degree of freedom robomech whose architecture is based on the 7R chain. The robomech is capable of performing two-function tasks. The features, kinematic constraints, and synthesis procedure of the robomech are outlined and an application example is given.

Kinematic and Kinetostatic Synthesis of Planar Coupled Serial Chain Mechanisms

2002 ◽  
Vol 124 (2) ◽  
pp. 301-312 ◽  
Author(s):  
Venkat Krovi ◽  
G. K. Ananthasuresh ◽  
Vijay Kumar
Keyword(s):  
Degree Of Freedom ◽  
Dimensional Synthesis ◽  
Single Degree Of Freedom ◽  
End Effector ◽  
Solution Approach ◽  
Single Degree ◽  
Design Specifications ◽  
Serial Chain ◽  
Gear Trains ◽  
External Loads

Single Degree-of-freedom Coupled Serial Chain (SDCSC) mechanisms form a novel class of modular and compact mechanisms with a single degree-of-freedom, suitable for a number of manipulation tasks. Such SDCSC mechanisms take advantage of the hardware constraints between the articulations of a serial-chain linkage, created using gear-trains or belt/pulley drives, to guide the end-effector motions and forces. In this paper, we examine the dimensional synthesis of such SDCSC mechanisms to perform desired planar manipulation tasks, taking into account task specifications on both end-effector motions and forces. Our solution approach combines precision point synthesis with optimization to realize optimal mechanisms, which satisfy the design specifications exactly at the selected precision points and approximate them in the least-squares sense elsewhere along a specified trajectory. The designed mechanisms can guide a rigid body through several positions while supporting arbitrarily specified external loads. Furthermore, torsional springs are added at the joints to reduce the overall actuation requirements and to enhance the task performance. Examples from the kinematic and the kinetostatic synthesis of planar SDCSC mechanisms are presented to highlight the benefits.

Three-Degree-of-Freedom Parallel Robot Arm

2006 ◽  
Author(s):  
Martin Hosek ◽  
Michael Valasek ◽  
Jairo Moura
Keyword(s):  
Parallel Robot ◽  
Degree Of Freedom ◽  
Motion Path ◽  
Angular Orientation ◽  
Robot Arm ◽  
Flat Panel Display ◽  
End Effector ◽  
Cluster Tools ◽  
Manufacturing Applications ◽  
Three Degree Of Freedom

This paper presents single- and dual-end-effector configurations of a planar three-degree of freedom parallel robot arm designed for automated pick-place operations in vacuum cluster tools for semiconductor and flat-panel-display manufacturing applications. The basic single end-effector configuration of the arm consists of a pivoting base platform, two elbow platforms and a wrist platform, which are connected through two symmetric pairs of parallelogram mechanisms. The wrist platform carries an end-effector, the position and angular orientation of which can be controlled independently by three motors located at the base of the robot. The joints and links of the mechanism are arranged in a unique geometric configuration which provides a sufficient range of motion for typical vacuum cluster tools. The geometric properties of the mechanism are further optimized for a given motion path of the robot. In addition to the basic symmetric single end-effector configuration, an asymmetric costeffective version of the mechanism is derived, and two dual-end-effector alternatives for improved throughput performance are described. In contrast to prior attempts to control angular orientation of the end-effector(s) of the conventional arms employed currently in vacuum cluster tools, all of the motors that drive the arm can be located at the stationary base of the robot with no need for joint actuators carried by the arm or complicated belt arrangements running through the arm. As a result, the motors do not contribute to the mass and inertia properties of the moving parts of the arm, no power and signal wires through the arm are necessary, the reliability and maintenance aspects of operation are improved, and the level of undesirable particle generation is reduced. This is particularly beneficial for high-throughput applications in vacuum and particlesensitive environments.

Force Capabilities of Two-Degree-of-Freedom Serial Robots Equipped With Passive Isotropic Force Limiters

2015 ◽  
Author(s):  
Meiying Zhang ◽  
Thierry Laliberté ◽  
Clément Gosselin
Keyword(s):  
Human Robot Interaction ◽  
Contact Forces ◽  
Degree Of Freedom ◽  
Practical Implementation ◽  
Robot Interaction ◽  
End Effector ◽  
Serial Robots ◽  
Serial Robot ◽  
Maximum Contact ◽  
Two Degree Of Freedom

This paper proposes the use of passive force and torque limiting devices to bound the maximum forces that can be applied at the end-effector or along the links of a robot, thereby ensuring the safety of human-robot interaction. Planar isotropic force limiting modules are proposed and used to analyze the force capabilities of a two-degree-of-freedom planar serial robot. The force capabilities at the end-effector are first analyzed. It is shown that, using isotropic force limiting modules, the performance to safety index remains excellent for all configurations of the robot. The maximum contact forces along the links of the robot are then analyzed. Force and torque limiters are distributed along the structure of the robot in order to ensure that the forces applied at any point of contact along the links are bounded. A power analysis is then presented in order to support the results. Finally, examples of mechanical designs of force/torque limiters are shown to illustrate a possible practical implementation of the concept.

On the Seven Position Synthesis of a 5-SS Platform Linkage

1997 ◽  
Vol 123 (1) ◽  
pp. 74-79 ◽  
Author(s):  
Qizheng Liao ◽  
J. Michael McCarthy
Keyword(s):  
Rigid Body ◽  
Reference Point ◽  
Polynomial Solution ◽  
Degree Of Freedom ◽  
Prismatic Joint ◽  
Movement Characteristics ◽  
Position Synthesis ◽  
Freedom Movement

This paper builds on Innocenti’s polynomial solution for the 5-SS platform that generates a one-degree of freedom movement through seven specified spatial positions of a rigid body. We show that his 60×60 resultant can be reduced to one that is 10×10. We then actuate the linkage using a prismatic joint on the sixth leg and determine the trajectory of the reference point through the specified positions. The singularity submanifold of this associated 6-SS platform provides information about the movement characteristics of the 5-SS linkage.

scholarly journals Increasing ABB FlexPicker Robot’s Degree of Freedom (DOF) using Flexible End Effector

2016 ◽  
Vol 78 ◽  
pp. 01056
Author(s):  
M. H. Nordin ◽  
K. Selvaraju ◽  
M. Fathullah
Keyword(s):  
Degree Of Freedom ◽  
End Effector

Parametric Design of a Spherical Eight-Bar Linkage Based on a Spherical Parallel Manipulator

2008 ◽  
Vol 1 (1) ◽  
Author(s):  
Gim Song Soh ◽  
J. Michael McCarthy
Keyword(s):  
Inverse Kinematics ◽  
Parallel Manipulator ◽  
Parametric Design ◽  
Degree Of Freedom ◽  
Kinematics Analysis ◽  
End Effector ◽  
Arbitrary Base ◽  
Three Degree Of Freedom ◽  
Spherical Parallel Manipulator

This paper presents a procedure that determines the dimensions of two constraining links to be added to a three degree-of-freedom spherical parallel manipulator so that it becomes a one degree-of-freedom spherical (8, 10) eight-bar linkage that guides its end-effector through five task poses. The dimensions of the spherical parallel manipulator are unconstrained, which provides the freedom to specify arbitrary base attachment points as well as the opportunity to shape the overall movement of the linkage. Inverse kinematics analysis of the spherical parallel manipulator provides a set of relative poses between all of the links, which are used to formulate the synthesis equations for spherical RR chains connecting any two of these links. The analysis of the resulting spherical eight-bar linkage verifies the movement of the system.

Five Position Synthesis of a Slider-Crank Function Generator

2011 ◽  
Author(s):  
Mark M. Plecnik ◽  
J. Michael McCarthy
Keyword(s):  
Full Range ◽  
Linear Actuator ◽  
Tolerance Zone ◽  
Function Generator ◽  
Front End ◽  
Input And Output ◽  
Function Generators ◽  
Synthesis Procedure ◽  
Position Synthesis ◽  
Branching Solutions

In this paper, we present a synthesis procedure for the coupler link of a planar slider-crank linkage in order to coordinate input by a linear actuator with the rotation of an output crank. This problem can be formulated in a manner similar to the synthesis of a five position RR coupler link. It is well-known that the resulting equations can produce branching solutions that are not useful. This is addressed by introducing tolerances for the input and output values of the specified task function. The proposed synthesis procedure is then executed on two examples. In the first example, a survey of solutions for tolerance zones of increasing size is conducted. In this example we find that a tolerance zone of 5% of the desired full range results in a number of useful task functions and usable slider-crank function generators. To demonstrate the use of these results, we present an example design for the actuator of the shovel of a front-end loader.

Sign in / Sign up

Export Citation Format

Share Document