Development and Preliminary Validation of a 50th Percentile Pedestrian Finite Element Model

2015 ◽  
Author(s):  
Costin D. Untaroiu ◽  
Jacob B. Putnam ◽  
Jeremy Schap ◽  
Matt L. Davis ◽  
F. Scott Gayzik
Keyword(s):  
Finite Element ◽  
Lumbar Spine ◽  
Test Data ◽  
Element Model ◽  
Human Model ◽  
Whole Body ◽  
Fe Model ◽  
Pedestrian Protection ◽  
Bending Tests ◽  
Impact Tests

Pedestrians represent one of the most vulnerable road users and comprise nearly 22% of the road crash related fatalities in the world. Therefore, protection of pedestrians in the car-to-pedestrian collisions (CPC) has recently generated increased attention with regulations which involve three subsystem tests for adult pedestrian protection (leg, thigh and head impact tests). The development of a finite element (FE) pedestrian model could be a better alternative that characterizes the whole-body response of vehicle–pedestrian interactions and assesses the pedestrian injuries. The main goal of this study was to develop and to preliminarily validate a FE model corresponding to a 50th male pedestrian in standing posture. The FE model mesh and defined material properties are based on the Global Human Body Modeling (GHBMC) 50th percentile male occupant model. The lower limb-pelvis and lumbar spine regions of the human model were preliminarily validated against the post mortem human surrogate (PMHS) test data recorded in four-point lateral knee bending tests, pelvic impact tests, and lumbar spine bending tests. Then, pedestrian-to-vehicle impact simulations were performed using the whole pedestrian model and the results were compared to corresponding pedestrian PMHS tests. Overall, the preliminary simulation results showed that lower leg response is close to the upper boundaries of PMHS corridors. The pedestrian kinematics predicted by the model was also in the overall range of test data obtained with PMHS with various anthropometries. In addition, the model shows capability to predict the most common injuries observed in pedestrian accidents. Generally, the validated pedestrian model may be used by safety researchers in the design of front ends of new vehicles in order to increase pedestrian protection.

A Finite Element Model of a Midsize Male for Simulating Pedestrian Accidents

2017 ◽  
Vol 140 (1) ◽  
Author(s):  
Costin D. Untaroiu ◽  
Wansoo Pak ◽  
Yunzhu Meng ◽  
Jeremy Schap ◽  
Bharath Koya ◽  
...  
Keyword(s):  
Finite Element ◽  
Lumbar Spine ◽  
Element Model ◽  
Human Model ◽  
Whole Body ◽  
Fe Model ◽  
Bending Tests ◽  
Lower Extremity Injuries ◽  
Pedestrian Accidents ◽  
Extremity Injuries

Pedestrians represent one of the most vulnerable road users and comprise nearly 22% the road crash-related fatalities in the world. Therefore, protection of pedestrians in car-to-pedestrian collisions (CPC) has recently generated increased attention with regulations involving three subsystem tests. The development of a finite element (FE) pedestrian model could provide a complementary component that characterizes the whole-body response of vehicle–pedestrian interactions and assesses the pedestrian injuries. The main goal of this study was to develop and to validate a simplified full body FE model corresponding to a 50th male pedestrian in standing posture (M50-PS). The FE model mesh and defined material properties are based on a 50th percentile male occupant model. The lower limb-pelvis and lumbar spine regions of the human model were validated against the postmortem human surrogate (PMHS) test data recorded in four-point lateral knee bending tests, pelvic\abdomen\shoulder\thoracic impact tests, and lumbar spine bending tests. Then, a pedestrian-to-vehicle impact simulation was performed using the whole pedestrian model, and the results were compared to corresponding PMHS tests. Overall, the simulation results showed that lower leg response is mostly within the boundaries of PMHS corridors. In addition, the model shows the capability to predict the most common lower extremity injuries observed in pedestrian accidents. Generally, the validated pedestrian model may be used by safety researchers in the design of front ends of new vehicles in order to increase pedestrian protection.

A detailed finite element model of a mid-sized male for the investigation of traffic pedestrian accidents

2020 ◽  
pp. 095441192097622
Author(s):  
Daniel Grindle ◽  
Wansoo Pak ◽  
Berkan Guleyupoglu ◽  
Bharath Koya ◽  
F Scott Gayzik ◽  
...  
Keyword(s):  
Finite Element ◽  
Test Data ◽  
Element Model ◽  
Upper Body ◽  
Whole Body ◽  
Fe Model ◽  
Automotive Safety ◽  
Detailed Model ◽  
Body Regions ◽  
Safety Research

The pedestrian is one of the most vulnerable road users and comprises approximately 23% of the road crash-related fatalities in the world. To protect pedestrians during Car-to-Pedestrian Collisions (CPC), subsystem impact tests are used in regulations. These tests provide insight but cannot characterize the complex vehicle-pedestrian interaction. The main purpose of this study was to develop and validate a detailed pedestrian Finite Element (FE) model corresponding to a 50th percentile male to predict CPC induced injuries. The model geometry was reconstructed using a multi-modality protocol from medical images and exterior scan data corresponding to a mid-sized male volunteer. To investigate injury response, this model included internal organs, muscles and vessels. The lower extremity, shoulder and upper body of the model were validated against Post Mortem Human Surrogate (PMHS) test data in valgus bending, and lateral/anterior-lateral blunt impacts, respectively. The whole-body pedestrian model was validated in CPC simulations using a mid-sized sedan and simplified generic vehicles bucks and previously unpublished PMHS coronal knee angle data. In the component validations, the responses of the FE model were mostly within PMHS test corridors and in whole body validations the kinematic and injury responses predicted by the model showed similar trends to PMHS test data. Overall, the detailed model showed higher biofidelity, especially in the upper body regions, compared to a previously reported simplified pedestrian model, which recommends using it in future pedestrian automotive safety research.

A Biomechanical Model of Lumbar Spine

2000 ◽  
Author(s):  
Subramanya Uppala ◽  
Robert X. Gao ◽  
Scott Cowan ◽  
K. Francis Lee
Keyword(s):  
Finite Element ◽  
Lumbar Spine ◽  
Experimental Studies ◽  
Three Dimensional ◽  
Biomechanical Model ◽  
Element Model ◽  
Fe Model ◽  
Flexion Extension ◽  
Cortical Shell ◽  
Three Dimensional Finite Element

Abstract The strength and stability of the lumbar spine are determined not only by the bone and muscles, but also by the visco-elastic structures and the interplay between the different components of the spine, such as ligaments, capsules, annulus fibrosis, and articular cartilage. In this paper we present a non-linear three-dimensional Finite Element model of the lumbar spine. Specifically, a three-dimensional FE model of the L4-5 one-motion segment/2 vertebrae was developed. The cortical shell and the cancellous bone of the vertebral body were modeled as 3D isoparametric eight-nodal elements. Finite element models of spinal injuries with fixation devices are also developed. The deformations across the different sections of the spine are observed under the application of axial compression, flexion/extension, and lateral bending. The developed FE models provided input to both the fixture design and experimental studies.

Simulation of the Transverse Fractures of the Sacrum Using a Finite Element Model of Lumbar Spine-Pelvis Segment

2008 ◽  
Author(s):  
A. Ivanov ◽  
A. Kiapour ◽  
N. Ebraheim ◽  
V. K. Goel
Keyword(s):  
Finite Element ◽  
Lumbar Spine ◽  
Finite Element Model ◽  
Treatment Options ◽  
Element Model ◽  
Severe Trauma ◽  
Fe Model ◽  
Element Analysis ◽  
Modern Computer ◽  
Transverse Fractures

The sacrum fractures are very severe trauma which frequently accompanied with lumbar spine fractures. The surgical procedures often require primary stabilization of both lumbar spine and sacrum. To understand the rationale of the instrumentation numerous cadaveric studies were conducted to elucidate the anatomy of fractures and treatment options [1,2,3]. The modern computer technology allowed simulating the fractures and repairing using the Finite Element Analysis, also [4,5]. The last method has a raw of advantages versus cadaveric method such as higher reliability, accuracy, and safety. Finite element investigations of the pelvic fractures allowed comparing the influence of implants on pelvis stability. However, the extensive search of the literature failed to find a finite element model which includes the pelvis and lumbar spine together. Current study is the first step to accomplish this goal. An experimentally validated model of ligamentous lumbar spine was combined with the FE model of pelvis [7], and simulation of the sacrum fractures was conducted.

A Finite Element Investigation of a Functional Spine Unit in Conjunction With a Multi-Body Model of the Lumbar Spine for Impact Dynamics

Volume 2 ◽  
2004 ◽  
Author(s):  
Volkan Esat ◽  
Memis Acar
Keyword(s):  
Finite Element ◽  
Lumbar Spine ◽  
Reaction Force ◽  
Element Model ◽  
Fe Model ◽  
Body Model ◽  
Spine Model ◽  
Spinal Segments ◽  
Whole Spine ◽  
Multi Body

In this study, the finite element (FE) technique was used in conjunction with multi-body modelling to simulate and analyse the dynamic behaviour of the spinal segments in order to investigate the effects of impact loadings on the lumbar spine. A 3-D multi-body model of the lumbar spine and an FE model of the L2-L3 motion segment were developed. Both models were validated for flexion and compression loadings, showing good agreements with a previously validated lumbar spine model. The predictions of the multi-body model under dynamic impact loading conditions such as reaction forces at lumbar motion segments were employed as force boundary conditions for the finite element model of the selected functional spine unit (FSU). Stress and pressure in the intervertebral disc element and the reaction force at a specific vertebral level were presented. This approach has the potential to more realistically simulate the dynamics of spinal segments and whole spine, and study the effects on spinal elements.

Prediction of the Modal Characteristics of the Human Spine at Resonant Frequency Using Finite Element Models

2005 ◽  
Vol 219 (4) ◽  
pp. 277-284 ◽  
Author(s):  
Li-Xin Guo ◽  
Ee-Chon Teo
Keyword(s):  
Finite Element ◽  
Lumbar Spine ◽  
Sagittal Plane ◽  
Whole Body Vibration ◽  
Vertical Motion ◽  
Element Model ◽  
Upper Body ◽  
Whole Body ◽  
Body Vibration ◽  
Human Spine

To understand the dynamic characteristics of the human spine, a detailed three-dimensional finite element model of the lower thorax to pelvis segment, T12-pelvis, was developed based on actual vertebral geometry. After modal analysis, the resonant frequencies of different spinal segments were obtained. The vibration mode of T12-pelvis shows that the human upper body mainly performs the vertical motion during whole-body vibration and the lumbar spine segment conducts translation and rotation in the sagittal plane. The lower segments of the lumbar spine move in flexion and the upper lumbar segments move in extension. This investigation may be helpful in understanding further the biomechanical behaviour of the human spine under the condition of whole-body vibration and to offer potential references for spinal disease treatments and product design in industry.

Finite Element Analysis of the Distributed Vibration Absorbers for Structural Noise Control

2005 ◽  
Author(s):  
Ashwini Gautam ◽  
Chris Fuller ◽  
James Carneal
Keyword(s):  
Finite Element ◽  
Numerical Model ◽  
Base Plate ◽  
Element Model ◽  
Fe Model ◽  
Vibration Absorbers ◽  
Element Analysis ◽  
Poroelastic Media ◽  
Hexahedral Elements ◽  
Component Models

This work presents an extensive analysis of the properties of distributed vibration absorbers (DVAs) and their effectiveness in controlling the sound radiation from the base structure. The DVA acts as a distributed mass absorber consisting of a thin metal sheet covering a layer of acoustic foam (porous media) that behaves like a distributed spring-mass-damper system. To assess the effectiveness of these DVAs in controlling the vibration of the base structures (plate) a detailed finite elements model has been developed for the DVA and base plate structure. The foam was modeled as a poroelastic media using 8 node hexahedral elements. The structural (plate) domain was modeled using 16 degree of freedom plate elements. Each of the finite element models have been validated by comparing the numerical results with the available analytical and experimental results. These component models were combined to model the DVA. Preliminary experiments conducted on the DVAs have shown an excellent agreement between the results obtained from the numerical model of the DVA and from the experiments. The component models and the DVA model were then combined into a larger FE model comprised of a base plate with the DVA treatment on its surface. The results from the simulation of this numerical model have shown that there has been a significant reduction in the vibration levels of the base plate due to DVA treatment on it. It has been shown from this work that the inclusion of the DVAs on the base plate reduces their vibration response and therefore the radiated noise. Moreover, the detailed development of the finite element model for the foam has provided us with the capability to analyze the physics behind the behavior of the distributed vibration absorbers (DVAs) and to develop more optimized designs for the same.

Finite Element Model of Human Cochlea Considering of the Helicotrema Size

2013 ◽  
Vol 456 ◽  
pp. 576-581 ◽  
Author(s):  
Li Fu Xu ◽  
Na Ta ◽  
Zhu Shi Rao ◽  
Jia Bin Tian
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Basilar Membrane ◽  
Round Window ◽  
Element Model ◽  
Oval Window ◽  
Fe Model ◽  
Cochlear Duct ◽  
Human Cochlea ◽  
Set Up

A 2-D finite element model of human cochlea is established in this paper. This model includes the structure of oval window, round window, basilar membrane and cochlear duct which is filled with fluid. The basilar membrane responses are calculated with sound input on the oval window membrane. In order to study the effects of helicotrema on basilar membrane response, three different helicotrema dimensions are set up in the FE model. A two-way fluid-structure interaction numerical method is used to compute the responses in the cochlea. The influence of the helicotrema is acquired and the frequency selectivity of the basilar membrane motion along the cochlear duct is predicted. These results agree with the experiments and indicate much better results are obtained with appropriate helicotrema size.

Analysis of Thick-Walled Pipeline Elements Operating in Creep Conditions

2015 ◽  
Vol 712 ◽  
pp. 63-68
Author(s):  
Przemysław Osocha ◽  
Bohdan Węglowski
Keyword(s):  
Finite Element ◽  
Test Data ◽  
Creep Test ◽  
Power Plants ◽  
Steam Pressure ◽  
Creep Model ◽  
Creep Process ◽  
Fe Model ◽  
Element Analysis ◽  
Wide Range

In some coal-fired power plants, pipeline elements have worked for over 200 000 hours and increased number of failures is observed. The paper discuses thermal wear processes that take place in those elements and lead to rupture. Mathematical model based on creep test data, and describing creep processes for analyzed material, has been developed. Model has been verified for pipeline operating temperature, lower than tests temperature, basing on Larson-Miller relation. Prepared model has been used for thermal-strength calculations based on a finite element method. Processes taking place inside of element and leading to its failure has been described. Than, basing on prepared mathematical creep model and FE model introduced to Ansys program further researches are made. Analysis of dimensions and shape of pipe junction and its influence on operational element lifetime is presented. In the end multi variable dependence of temperature, steam pressure and element geometry is shown, allowing optimization of process parameters in function of required operational time or maximization of steam parameters. The article presents wide range of methods. The creep test data were recalculated for operational temperature using Larson-Miller parameter. The creep strain were modelled, used equations and their parameters are presented. Analysis of errors were conducted. Geometry of failing pipe junction was introduced to the Ansys program and the finite element analysis of creep process were conducted.

Sign in / Sign up

Export Citation Format

Share Document