Designing Wind Turbines for Areas With Low Wind Speeds

2014 ◽  
Author(s):  
Mohammed S. Mayeed ◽  
Adeel Khalid
Keyword(s):  
Energy Consumption ◽  
Wind Speed ◽  
Wind Energy ◽  
Wind Turbines ◽  
Small Scale ◽  
Wind Speeds ◽  
Low Wind Speed ◽  
Average Wind ◽  
The World ◽  
Low Wind Speeds

Today’s wind turbines are designed in a wide range of vertical and horizontal axis types. In this study, several wind turbines are designed for low wind speed areas around the world mainly for domestic energy consumption. The wind speed range of 4–12 mph is considered, which is selected based on the average wind speeds in the Atlanta, GA and surrounding areas. These areas have relatively low average wind speeds compared to various other parts of the United States. Wind energy has been identified as an important source of renewable energy. Traditionally wind energy utilization is limited to areas with higher wind speeds. In reality a lot of areas in the world including Atlanta, GA., have low average wind speeds and demand high energy consumption. In most cases, wind turbines are installed in remote offshore or away from habitat locations, causing heavy investment in installation and maintenance, and loss of energy transfer over long distances. Therefore, the main focus of this study is to extract wind energy domestically at low wind speeds. A few more advantages of small scale wind turbines include reduced visibility, less noise and reduced detrimental environmental effects such as killing of birds, when compared to traditional large turbines. With the latest development in wind turbine technology it is now possible to employ small scale wind turbines that have much smaller foot print and can generate enough energy for small businesses or residential applications. The low speed wind turbines are typically located near residential areas, and are much smaller in sizes compared to the large out of habitat wind turbines. In this study, several designs of wind turbines are modeled using SolidWorks. Virtual aerodynamic analysis is performed using SolidWorks Flow simulation software, and then optimization of the designs is performed based on maximizing the starting rotational torque and acceleration. From flow simulations, forces on the wind turbine blades and structures are calculated, and used in subsequent stress analysis to confirm structural integrity. Critical insight into the low wind speed turbine design is obtained using various configurations and the results are discussed. The study will help identify bottlenecks in the practical and effective utilization of low speed wind energy, and help devise possible remedial plans for the areas around the globe that get low average wind speeds.

Optimization of the Wind Turbine Designs for Areas With Low Wind Speeds

2015 ◽  
Author(s):  
Mohammed S. Mayeed ◽  
Adeel Khalid
Keyword(s):  
Energy Consumption ◽  
Wind Speed ◽  
Wind Energy ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Small Scale ◽  
Wind Speeds ◽  
Low Wind Speed ◽  
Average Wind ◽  
The World

Wind energy has been identified as an important source of renewable energy. In this study, several wind turbine designs have been analyzed and optimized designs have been proposed for low wind speed areas around the world mainly for domestic energy consumption. The wind speed range of 4–12 mph is considered, which is selected based on the average wind speeds in the Atlanta, GA and surrounding areas. These areas have relatively low average wind speeds compared to various other parts of the United States. Traditionally wind energy utilization is limited to areas with higher wind speeds. In reality a lot of areas in the world have low average wind speeds and demand high energy consumption. In most cases, wind turbines are installed in remote offshore or away from habitat high wind locations, causing heavy investment in installation and maintenance, and loss of energy transfer over long distance. A few more advantages of small scale wind turbines include reduced visibility, less noise and reduced detrimental environmental effects such as killing of birds, when compared to traditional large turbines. With the latest development in wind turbine technology it is now possible to employ small scale wind turbines that have much smaller foot print and can generate enough energy for small businesses or residential applications. The low speed wind turbines are typically located near residential areas, and are much smaller in sizes compared to the large out of habitat wind turbines. In this study, several designs of vertical and horizontal axes wind turbines are modeled using SolidWorks e.g. no-airfoil theme, airfoil blade, Savonius rotor etc. Virtual aerodynamic analysis is performed using SolidWorks Flow simulation software, and then optimization of the designs is performed based on maximizing the starting rotational torque and ultimate power generation capacity. From flow simulations, forces on the wind turbine blades and structures are calculated, and used in subsequent stress analysis to confirm structural integrity. Critical insight into low wind speed turbines is obtained using various configurations, and optimized designs have been proposed. The study will help in the practical and effective utilization of wind energy for the areas around the globe having low average wind speeds.

SHAPING OF AN AUTONOMOUS POWER SYSTEM FOR GUARANTEED POWER SUPPLY WITH THE PREDOMINANCE WIND ENERGY

2018 ◽  
pp. 28-50
Author(s):  
S. G. Ignatiev ◽  
S. V. Kiseleva
Keyword(s):  
Energy Storage ◽  
Wind Speed ◽  
Wind Energy ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Energy Demand ◽  
Diesel Generator ◽  
Average Wind Speed ◽  
Wind Speeds ◽  
Average Wind

Optimization of the autonomous wind-diesel plants composition and of their power for guaranteed energy supply, despite the long history of research, the diversity of approaches and methods, is an urgent problem. In this paper, a detailed analysis of the wind energy characteristics is proposed to shape an autonomous power system for a guaranteed power supply with predominance wind energy. The analysis was carried out on the basis of wind speed measurements in the south of the European part of Russia during 8 months at different heights with a discreteness of 10 minutes. As a result, we have obtained a sequence of average daily wind speeds and the sequences constructed by arbitrary variations in the distribution of average daily wind speeds in this interval. These sequences have been used to calculate energy balances in systems (wind turbines + diesel generator + consumer with constant and limited daily energy demand) and (wind turbines + diesel generator + consumer with constant and limited daily energy demand + energy storage). In order to maximize the use of wind energy, the wind turbine integrally for the period in question is assumed to produce the required amount of energy. For the generality of consideration, we have introduced the relative values of the required energy, relative energy produced by the wind turbine and the diesel generator and relative storage capacity by normalizing them to the swept area of the wind wheel. The paper shows the effect of the average wind speed over the period on the energy characteristics of the system (wind turbine + diesel generator + consumer). It was found that the wind turbine energy produced, wind turbine energy used by the consumer, fuel consumption, and fuel economy depend (close to cubic dependence) upon the specified average wind speed. It was found that, for the same system with a limited amount of required energy and high average wind speed over the period, the wind turbines with lower generator power and smaller wind wheel radius use wind energy more efficiently than the wind turbines with higher generator power and larger wind wheel radius at less average wind speed. For the system (wind turbine + diesel generator + energy storage + consumer) with increasing average speed for a given amount of energy required, which in general is covered by the energy production of wind turbines for the period, the maximum size capacity of the storage device decreases. With decreasing the energy storage capacity, the influence of the random nature of the change in wind speed decreases, and at some values of the relative capacity, it can be neglected.

Analysis of a Concept for a Low Wind Speed Tolerant Axial Wind Turbine

2011 ◽  
Author(s):  
Ali A. Ameri ◽  
Majid Rashidi
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Power Output ◽  
Turbine Rotor ◽  
Navier Stokes ◽  
Ambient Wind ◽  
Wind Speeds ◽  
Low Wind Speed ◽  
Low Wind Speeds

In this paper, the authors analyze a design for a wind tower intended for areas of low wind speeds. The wind tower consists of a combination of several rooftop size turbines arranged alongside a cylindrical structure that acts as a Wind Deflecting Structure (WDS). The WDS amplifies the effective wind speed thus allowing the turbine rotors to operate under lower ambient wind speeds. Analyses were performed using simple models as well as more sophisticated CFD methods employing Steady and Unsteady Reynolds Averaged Navier-Stokes methodology. The effect of the wind amplification was shown on a commercial small wind turbine power output map. Also, a wind turbine rotor flow was computed as operating alongside the WDS and compared to the computed operation of isolated turbines at equal effective and ambient wind velocities. The computational analyses of this work suggest that the power output of isolated rooftop wind turbines deployed at low to moderate wind speed may be matched by installing wind turbines alongside a cylindrical wind deflecting structure operating at lower wind speeds. Other benefits of the arrangement are also enumerated.

scholarly journals Wind Power potential in Kigali and Western provinces of Rwanda

2015 ◽  
Vol 2 (1) ◽  
pp. 25-36
Author(s):  
Otieno Fredrick Onyango ◽  
Sibomana Gaston ◽  
Elie Kabende ◽  
Felix Nkunda ◽  
Jared Hera Ndeda
Keyword(s):  
Wind Speed ◽  
Probability Density ◽  
Wind Power ◽  
Wind Direction ◽  
Small Scale ◽  
Energy Potential ◽  
Wind Speeds ◽  
Mean Wind Speed ◽  
Wind Energy Potential ◽  
Low Wind Speeds

Wind speed and wind direction are the most important characteristics for assessing wind energy potential of a location using suitable probability density functions. In this investigation, a hybrid-Weibull probability density function was used to analyze data from Kigali, Gisenyi, and Kamembe stations. Kigali is located in the Eastern side of Rwanda while Gisenyi and Kamembe are to the West. On-site hourly wind speed and wind direction data for the year 2007 were analyzed using Matlab programmes. The annual mean wind speed for Kigali, Gisenyi, and Kamembe sites were determined as 2.36m/s, 2.95m/s and 2.97m/s respectively, while corresponding dominant wind directions for the stations were ,  and  respectively. The annual wind power density of Kigali was found to be  while the power densities for Gisenyi and Kamembe were determined as and . It is clear, the investigated regions are dominated by low wind speeds thus are suitable for small-scale wind power generation especially at Kamembe site.

Effect of Slotted Angle on Savonius Wind Turbine Performance

2021 ◽  
Vol 104 ◽  
pp. 83-88
Author(s):  
Rahmat Wahyudi ◽  
Diniar Mungil Kurniawati ◽  
Alfian Djafar
Keyword(s):  
Wind Energy ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Electrical Energy ◽  
Speed Ratio ◽  
Angle Variation ◽  
Wind Speeds ◽  
Turbine Performance ◽  
Savonius Wind Turbine ◽  
Low Wind Speeds

The potential of wind energy is very abundant but its utilization is still low. The effort to utilize wind energy is to utilize wind energy into electrical energy using wind turbines. Savonius wind turbines have a very simple shape and construction, are inexpensive, and can be used at low wind speeds. This research aims to determine the effect of the slot angle on the slotted blades configuration on the performance produced by Savonius wind turbines. Slot angle variations used are 5o ,10o , and 15o with slotted blades 30% at wind speeds of 2,23 m/s to 4,7 m/s using wind tunnel. The result showed that a small slot angle variation of 5o produced better wind turbine performance compared to a standard blade at low wind speeds and a low tip speed ratio.

scholarly journals Strategies for Enhancing the Low Wind Speed Performance of H-Darrieus Wind Turbine—Part 1

2019 ◽  
Vol 1 (1) ◽  
pp. 185-204 ◽  
Author(s):  
Palanisamy Mohan Kumar ◽  
Krishnamoorthi Sivalingam ◽  
Teik-Cheng Lim ◽  
Seeram Ramakrishna ◽  
He Wei
Keyword(s):  
Wind Speed ◽  
Poor Performance ◽  
Vertical Axis ◽  
Speed Ratio ◽  
Wind Speeds ◽  
Low Wind Speed ◽  
Viable Solution ◽  
Speed Performance ◽  
Low Wind Speeds ◽  
Starting Characteristics

Small wind turbines are key devices for micro generation in particular, with a notable contribution to the global wind energy sector. Darrieus turbines, despite being highly efficient among various types of vertical axis turbines, received much less attention due to their starting characteristics and poor performance in low wind speeds. Radically different concepts are proposed as a potential solution to enhance the performance of Darrieus turbine in the weak wind flows, all along the course of Darrieus turbine development. This paper presents a comprehensive review of proposed concepts with the focus set on the low wind speed performance and critically assessing their applicability based on economics, reliability, complexity, and commercialization aspects. The study is first of its kind to consolidate and compare various approaches studied on the Darrieus turbine with the objective of increasing performance at low wind. Most of the evaluated solutions demonstrate better performance only in the limited tip speed ratio, though they improve the low wind speed performance. Several recommendations have been developed based on the evaluated concepts, and we concluded that further critical research is required for a viable solution in making the Darrieus turbine a low speed device.

Effect of Swell on Wind Stress for Light to Moderate Winds

2020 ◽  
Vol 77 (11) ◽  
pp. 3759-3768
Author(s):  
Charles L. Vincent ◽  
Hans C. Graber ◽  
Clarence O. Collins
Keyword(s):  
Wind Speed ◽  
Gulf Of Mexico ◽  
Inflection Point ◽  
Friction Velocity ◽  
Flow Transition ◽  
Wind Speeds ◽  
Impact Stress ◽  
Low Wind Speed ◽  
Wind Sea ◽  
Low Wind Speeds

AbstractBuoy observations from a 1999 Gulf of Mexico field program (GOM99) are used to investigate the relationships among friction velocity u*, wind speed U, and amount of swell present. A U–u*sea parameterization is developed for the case of pure wind sea (denoted by u*sea), which is linear in U over the range of available winds (2–16 m s−1). The curve shows no sign of an inflection point near 7–8 m s−1 as suggested in a 2012 paper by Andreas et al. on the basis of a transition from smooth to rough flow. When observations containing more than minimal swell energy are included, a different U–u* equation for U < 8 m s−1 is found, which would intersect the pure wind-sea curve about 7–8 m s−1. These two relationships yield a bilinear curve similar to Andreas et al. with an apparent inflection near 7–8 m s−1. The absence of the inflection in the GOM99 experiment pure wind-sea curve and the similarity of the GOM99 swell-dominated low wind speed to Andreas et al.’s low wind speed relationship suggest that the inflection may be due to the effect of swell and not a flow transition. Swell heights in the range of only 25–50 cm may be sufficient to impact stress at low wind speeds.

scholarly journals An Experimental Field Dataset with Buoyant, Neutral, and Dense Gas Atmospheric Releases and Model Comparisons in Low–Wind Speed (Diffusion) Conditions

2010 ◽  
Vol 49 (9) ◽  
pp. 1805-1817
Author(s):  
Veronica E. Wannberg ◽  
Gustavious Williams ◽  
Patrick Sawyer ◽  
Richard Venedam
Keyword(s):  
Wind Speed ◽  
Field Measurements ◽  
Release Rates ◽  
Wind Speeds ◽  
Low Wind Speed ◽  
Current State ◽  
Practice Models ◽  
Atmospheric Releases ◽  
Low Wind Speeds ◽  
Atmospheric Concentrations

Abstract A unique field dataset from a series of low–wind speed experiments, modeling efforts using three commonly used models to replicate these releases, and statistical analysis of how well these models were able to predict the plume concentrations is presented. The experiment was designed to generate a dataset to describe the behavior of gaseous plumes under low-wind conditions and the ability of current, commonly used models to predict these movements. The dataset documents the release and transport of three gases: ammonia (buoyant), ethylene (neutral), and propylene (dense) in low–wind speed (diffusion) conditions. Release rates ranged from 1 to 20 kg h−1. Ammonia and ethylene had five 5-min releases each to represent puff releases and five 20-min releases each to represent plume releases. Propylene had five 5-min puffs, six 20-min plumes, and a single 30-min plume. Thirty-two separate releases ranging from 6 to 47 min were conducted, of which only 30 releases generated useful data. The data collected included release rates, atmospheric concentrations to 100 m from the release point, and local meteorological conditions. The diagnostics included nine meteorological stations on 100-m centers and 36 photoionization detectors in a radial pattern. Three current state-of-the-practice models, Aerial Locations of Hazardous Atmospheres (ALOHA), Emergency Prediction Information code (EPIcode), and Second-Order Closure Integrated Puff (SCIPUFF), were used to try to duplicate the measured field results. Low wind speeds are difficult to model, and all of the models had difficulty replicating the field measurements. However, the work does show that these models, if used correctly, are conservative (overpredict concentrations) and can be used for safety and emergency planning.

ANALISA PERFORMA TURBIN ANGIN SUMBU HORISONTAL BERSUDU AIRFOIL MELALUI VARIASI JUMLAH SUDU

ROTOR ◽  
2018 ◽  
Vol 11 (2) ◽  
pp. 18
Author(s):  
Wabang A Jhon ◽  
Abanat D.J Jufra ◽  
Hattu Edwin
Keyword(s):  
Wind Speed ◽  
Kinetic Energy ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Mechanical Energy ◽  
Coefficient Of Performance ◽  
Research Activity ◽  
Average Wind Speed ◽  
Wind Speeds ◽  
Average Wind

Indonesia is an area that has the potential for sufficient wind resources to be utilized for kinetic energy into other energy such as mechanical energy and electrical energy through its generators (generators). The way to utilize wind kinetic energy into other energy is through a device called a wind turbine. Wind turbines have been around since ancient times, and are called airfoil angled wind turbines. This airfoil wind turbine is designed only for areas with average wind speeds above 6m / s. While in Indonesia not all regions have the same wind speed. In certain seasons, the average wind speed is below 6 m / s. This has become a major problem in regions that have average wind speeds below 6 m / s. Seeing this condition, there is a need for scientific research to obtain wind turbines that can be used in areas with average wind speeds below 5m / s. For this reason, the research I want to do is get a wind turbine that can be used as a power plant in areas that have wind speeds below 6m / s. This research was conducted on the basis of scientific theory in fluid mechanics regarding the sweeping area of wind turbines and the performance of variations in the number of blades in the wind. In addition, the research in several scientific journals was used as the basis of this research This research method is an experimental method, in the form of testing a wind turbine axis prototype horizontal and airfoil axis. The details of the research activity are the design and manufacture of laboratory scale horizontal airfoil axis turbines. Next, testing with a fan as a source of wind. The fan used has three variations of speed, all of which are used to determine the lowest average wind speed that can be applied. The results of the research are where wind turbines with the greatest torque and power and the Coefficient of Performance (CP) with the highest value will be used as a result to be applied to the community. Based on experimental data, it can be concluded that the greatest torque and power occur in turbines with 4 blades with details at speed 1, the largest torque and power are 0.201 Nm and 4.5 W; at speed 2, the biggest torque and power are 0.25 Nm and 7.21 W; at speed 3, the biggest torque and power are 0.28 Nm and 8.35 W Keywords: wind turbine, airfoil, nozzle, diffuser

Sign in / Sign up

Export Citation Format

Share Document