Numerical and Experimental Investigation on a Low-Speed Compressor Cascade With Circulation Control

2008 ◽  
Author(s):  
S. Fischer ◽  
H. Saathoff ◽  
R. Radespiel
Keyword(s):  
Wind Tunnel ◽  
Static Pressure ◽  
Three Dimensional ◽  
Pressure Rise ◽  
Circulation Control ◽  
Two Dimensional ◽  
Compressor Cascade ◽  
Flow Topology ◽  
Wind Tunnel Tests ◽  
Low Speed

Experimental and numerical results for the flow through a stator cascade with active flow control are discussed. By blowing air through a slot close to the trailing edge of the aerofoils, the deflection angle as well as the static pressure rise in the stator are increased. The aerofoil design is representative for a 1st-stage stator geometry of a multi-stage compressor adapted for low–speed applications. To allow a reasonable transfer of the high-speed results to low-speed wind tunnel conditions, a corresponding cascade geometry was generated applying the Prandtl–Glauert analogy. With this modified cascade numerical simulations and experiments have been conducted at a Reynolds number of 5 · 105. As a reference case two-dimensional flow simulations without circulation control are considered using a Navier–Stokes solver. In the related wind tunnel tests three–dimensional conditions occur in the test rig. Nevertheless five–hole probe measurements in the wake of the blade mid section show a good agreement with the theoretical characteristics. Additional investigation along the whole blade span gives a deeper insight into the flow topology. For design conditions different blowing rates are applied. The wind tunnel tests confirm the positive benefit, which is predicted by two-dimensional calculations. The offset between simulated and measured pressure rise decreases with increasing blowing mass flows due to the reduction of the axial velocity ratio. This result is related to a redistribution of the passage flow which can only be explained in a three–dimensional analysis including the side wall influence. The benefit of the circulation control at varying blowing rates is finally characterized by the efficiency and the static pressure rise per injected energy.

Numerical and Experimental Investigation of Return Channel Vane Aerodynamics With Two-Dimensional and Three-Dimensional Vanes

2016 ◽  
Vol 139 (1) ◽  
Author(s):  
A. Hildebrandt ◽  
F. Schilling
Keyword(s):  
Experimental Investigation ◽  
Flow Field ◽  
Static Pressure ◽  
Three Dimensional ◽  
Pressure Rise ◽  
Field Performance ◽  
Two Dimensional ◽  
Flow Angle ◽  
Overall Performance ◽  
Return Channel

The present paper deals with the numerical and experimental investigation of the effect of return channel (RCH) dimensions of a centrifugal compressor stage on the aerodynamic performance. Three different return channel stages were investigated, two stages comprising three-dimensional (3D) return channel blades and one stage comprising two-dimensional (2D) RCH vanes. The analysis was performed regarding both the investigation of overall performance (stage efficiency, RCH total pressure loss coefficient) and detailed flow-field performance. For detailed experimental flow-field investigation at the stage exit, six circumferentially traversed three-hole probes were positioned downstream the return channel exit in order to get two-dimensional flow-field information. Additionally, static pressure wall measurements were taken at the hub and shroud pressure and suction side (SS) of the 2D and 3D return channel blades. The return channel system overall performance was calculated by measurements of the circumferentially averaged 1D flow field downstream the diffuser exit and downstream the stage exit. Dependent on the type of return channel blade, the numerical and experimental results show a significant effect on the flow field overall and detail performance. In general, satisfactory agreement between computational fluid dynamics (CFD)-prediction and test-rig measurements was achieved regarding overall and flow-field performance. In comparison with the measurements, the CFD-calculated stage performance (efficiency and pressure rise coefficient) of all the 3D-RCH stages was slightly overpredicted. Very good agreement between CFD and measurement results was found for the static pressure distribution on the RCH wall surfaces while small CFD-deviations occur in the measured flow angle at the stage exit, dependent on the turbulence model selected.

Numerical Flow Analysis in a Subsonic Vaned Radial Diffuser With Leading Edge Redesign

1999 ◽  
Vol 121 (1) ◽  
pp. 119-126 ◽  
Author(s):  
E. Casartelli ◽  
A. P. Saxer ◽  
G. Gyarmathy
Keyword(s):  
Static Pressure ◽  
Flow Analysis ◽  
Three Dimensional ◽  
Pressure Rise ◽  
Leading Edge ◽  
Inverse Design ◽  
Navier Stokes ◽  
Two Dimensional ◽  
Characteristic Lines ◽  
Design Software

The flow field in a subsonic vaned radial diffuser of a single-stage centrifugal compressor is numerically investigated using a three-dimensional Navier–Stokes solver (TASCflow) and a two-dimensional analysis and inverse-design software package (MISES). The vane geometry is modified in the leading edge area (two-dimensional blade shaping) using MISES, without changing the diffuser throughflow characteristics. An analysis of the two-dimensional and three-dimensional effects of two redesigns on the flow in each of the diffuser subcomponents is performed in terms of static pressure recovery, total pressure loss production, and secondary flow reduction. The computed characteristic lines are compared with measurements, which confirm the improvement obtained by the leading edge redesign in terms of increased pressure rise and operating range.

Active Control of the Corner Separation on a Highly Loaded Compressor Cascade With Periodic Nonsteady Boundary Conditions by Means of Fluidic Actuators

2015 ◽  
Vol 138 (3) ◽  
Author(s):  
Marcel Staats ◽  
Wolfgang Nitsche
Keyword(s):  
Flow Field ◽  
Static Pressure ◽  
Active Flow Control ◽  
Three Dimensional ◽  
Pressure Rise ◽  
Compressor Cascade ◽  
Pulsed Detonation Engine ◽  
Detonation Engine ◽  
The Impact ◽  
Highly Loaded

This paper discusses the impact of a nonsteady outflow condition on the compressor stator flow that is forced through a mimic in the wake of a linear low-speed cascade to simulate the conditions that would be expected in a pulsed detonation engine. 2D/3C-PIV measurements were made to describe the flow field in the passage. Detailed wake measurements provide information about static pressure rise as well as total pressure loss. The stator profile used for the investigations is highly loaded and operates with three-dimensional flow separations under design conditions and without active flow control. It is shown that sidewall actuation helps stabilize the flow field at every phase angle and extends the operating range of the compressor stator. Furthermore, the static pressure gain can be increased by 6% with a 4% loss reduction in time-averaged data.

Control of Three-Dimensional Separations in Axial Compressors by Tailored Boundary Layer Suction

2007 ◽  
Vol 130 (1) ◽  
Author(s):  
Semiu A. Gbadebo ◽  
Nicholas A. Cumpsty ◽  
Tom P. Hynes
Keyword(s):  
Boundary Layer ◽  
Static Pressure ◽  
Three Dimensional ◽  
Pressure Rise ◽  
Surface Flow ◽  
Compressor Cascade ◽  
Suction Surface ◽  
Blade Passage ◽  
Boundary Layer Suction ◽  
End Wall

One of the important ways of improving turbomachinery compressor performance is to control three-dimensional (3D) separations, which form over the suction surface and end wall corner of the blade passage. Based on the insights gained into the formation of these separations, this paper illustrates how an appropriately applied boundary layer suction of up to 0.7% of inlet mass flow can control and eliminate typical compressor stator hub corner 3D separation over a range of operating incidence. The paper describes, using computational fluid dynamics, the application of suction on the blade suction surface and end wall boundary layers and exemplifies the influence of end wall dividing streamline in initiating 3D separation in the blade passage. The removal of the separated region from the blade suction surface is confirmed by an experimental investigation in a compressor cascade involving surface flow visualization, surface static pressure, and exit loss measurements. The ensuing passage flow field is characterized by increased blade loading (static pressure difference between pressure and suction surface), enhanced average static pressure rise, significant loss removal, and a uniform exit flow. This result also enables the contribution of the 3D separation to the overall loss and passage blockage to be assessed.

Active Control of the Corner Separation on a Highly Loaded Compressor Cascade With Periodic Non-Steady Boundary Conditions by Means of Fluidic Actuators

2015 ◽  
Author(s):  
Marcel Staats ◽  
Wolfgang Nitsche
Keyword(s):  
Flow Field ◽  
Static Pressure ◽  
Active Flow Control ◽  
Three Dimensional ◽  
Pressure Rise ◽  
Side Wall ◽  
Compressor Cascade ◽  
Detonation Engine ◽  
The Impact ◽  
Highly Loaded

This contribution discusses the impact of a non-steady outflow condition on the compressor stator flow that is forced through a mimic in the wake of a linear low speed cascade to simulate the conditions that would be expected in a pulsed detonation engine. 2D/3C-PIV measurements were made to describe the flow field in the passage. Detailed wake measurements provide information about static pressure rise as well as total pressure loss. The stator profile used for the investigations is highly loaded and operates with three-dimensional flow separations under design conditions and without active flow control. It is shown that side wall actuation helps to stabilize the flow field at every phase angle and extends the operating range of the compressor stator. Furthermore, the static pressure gain can be increased by 6% with a 4% loss reduction in time averaged data.

Permissible three-dimensional testing in a two-dimensional adaptive wall wind tunnel

AIAA Journal ◽  
1997 ◽  
Vol 35 ◽  
pp. 749-750
Author(s):  
David Sumner ◽  
Ewart Brundrett
Keyword(s):  
Wind Tunnel ◽  
Three Dimensional ◽  
Two Dimensional

Numerical investigations on the effect of volute casing treatment for performance augmentation in a centrifugal fan

2021 ◽  
pp. 095440622110341
Author(s):  
Manjunath L Nilugal ◽  
K Vasudeva Karanth ◽  
Madhwesh N
Keyword(s):  
Total Pressure ◽  
Static Pressure ◽  
Numerical Study ◽  
Pressure Coefficient ◽  
Three Dimensional ◽  
Pressure Rise ◽  
Centrifugal Fan ◽  
Casing Treatment ◽  
Sliding Mesh ◽  
Optimum Configuration

This article presents the effect of volute chamfering on the performance of a forward swept centrifugal fan. The numerical analysis is performed to obtain the performance parameters such as static pressure rise coefficient and total pressure coefficient for various flow coefficients. The chamfer ratio for the volute is optimized parametrically by providing a chamfer on either side of the volute. The influence of the chamfer ratio on the three dimensional flow domain was investigated numerically. The simulation is carried out using Re-Normalisation Group (RNG) k-[Formula: see text] turbulence model. The transient simulation of the fan system is done using standard sliding mesh method available in Fluent. It is found from the analysis that, configuration with chamfer ratio of 4.4 is found be the optimum configuration in terms of better performance characteristics. On an average, this optimum configuration provides improvement of about 6.3% in static pressure rise coefficient when compared to the base model. This optimized chamfer configuration also gives a higher total pressure coefficient of about 3% validating the augmentation in static pressure rise coefficient with respect to the base model. Hence, this numerical study establishes the effectiveness of optimally providing volute chamfer on the overall performance improvement of forward bladed centrifugal fan.

Three-dimensional flow in cavities

1963 ◽  
Vol 16 (4) ◽  
pp. 620-632 ◽  
Author(s):  
D. J. Maull ◽  
L. F. East
Keyword(s):  
Static Pressure ◽  
Three Dimensional ◽  
Two Dimensional ◽  
Three Dimensional Flow ◽  
Large Span ◽  
Dimensional Flow ◽  
Pressure Distributions ◽  
Oil Flow ◽  
Two Dimensional Flow

The flow inside rectangular and other cavities in a wall has been investigated at low subsonic velocities using oil flow and surface static-pressure distributions. Evidence has been found of regular three-dimensional flows in cavities with large span-to-chord ratios which would normally be considered to have two-dimensional flow near their centre-lines. The dependence of the steadiness of the flow upon the cavity's span as well as its chord and depth has also been observed.

Sign in / Sign up

Export Citation Format

Share Document