Improved Trench Film Cooling With Shaped Trench Outlets

2011 ◽  
Author(s):  
Habeeb Idowu Oguntade ◽  
Gordon E. Andrews ◽  
Alan Burns ◽  
Derek B. Ingham ◽  
Mohammed Pourkashanian
Keyword(s):  
Mass Flow ◽  
Film Cooling ◽  
Cross Flow ◽  
Trailing Edge ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Vertical Slot ◽  
Superior Surface ◽  
Cooling Air ◽  
Computational Predictions

This paper presents the influence of the shaped trailing edge of trench outlets on film cooling effectiveness and aerodynamics. A 90° outlet wall to a trench will give a vertical slot jet into the cross flow and it was considered that improvements in the cooling effectiveness would occur if the trailing edge of the trench outlet was bevelled or filleted. CFD approach was used for these investigations which started with the predictions of the conventional sharp edged trench outlet for two experimental geometries. The computational predictions for the conventional sharp edged trench outlet were shown to have good agreement with the experimental data for two experimental geometries. The shaped trailing edge of the trench outlet was predicted to improve the film cooling effectiveness. The bevelled and filleted trench outlets were predicted to further suppress vertical jet momentum and give a Coanda effect that allowed the cooling air to attach to the downstream wall surface with a better transverse spread of the coolant film. The new trench outlet geometries would allow a reduction in film cooling mass flow rate for the same cooling effectiveness. Also, it was predicted that reducing the coolant mass flow per hole and increasing the number of holes gave, for the same total coolant mass flow, a much superior surface averaged cooling effectiveness for the same cooled surface area.

Improved Trench Film Cooling With Shaped Trench Outlets

2012 ◽  
Vol 135 (2) ◽  
Author(s):  
Habeeb Idowu Oguntade ◽  
Gordon E. Andrews ◽  
A. D. Burns ◽  
Derek B. Ingham ◽  
Mohammed Pourkashanian
Keyword(s):  
Flat Plate ◽  
Mass Flow ◽  
Film Cooling ◽  
Cross Flow ◽  
Suction Side ◽  
Experimental Results ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Vertical Slot ◽  
Cooling Hole

The influence of the shape of the downstream edge of trench film cooling hole outlets on film cooling effectiveness was investigated using CFD for flat plate film cooling. A 90 deg trench outlet wall with impinging 30 deg film cooling jets results in improved transverse film cooling effectiveness but produces a vertical slot jet into the cross flow, which is not the best aerodynamics for optimum film cooling. It was considered that improvements in the cooling effectiveness would occur if the trailing edge of the trench outlet produced a flow that was inclined in the direction of the crossflow. Beveled and filleted trench outlet shapes were investigated. The CFD predictions were shown to predict well the conventional sharp edged trench outlet experimental results for a flat plate geometry. The flat plate CFD predictions were also shown to predict the experimental results for trench cooling on the suction side of a turbine vane, where the local curvature was small relative to the trench width. The beveled and filleted trench outlets were predicted to suppress the vertical jet momentum and give a Coanda effect that allowed the cooling air to attach to the downstream wall surface. This produced an improved transverse spread of the coolant. Also, it was predicted that reducing the coolant mass flow per hole and increasing the number of rows of holes gave, for the same total coolant mass flow and the same surface area, a superior surface averaged cooling effectiveness.

Pressure Side and Cutback Trailing Edge Film Cooling in a Linear Nozzle Vane Cascade at Different Mach Numbers

2012 ◽  
Vol 134 (5) ◽  
Author(s):  
Giovanna Barigozzi ◽  
Antonio Perdichizzi ◽  
Silvia Ravelli
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Pressure Side ◽  
Trailing Edge ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Mach Numbers ◽  
Nozzle Guide ◽  
Cooling Air ◽  
Momentum Boundary Layer

Tests on a specifically designed linear nozzle guide vane cascade with trailing edge coolant ejection were carried out to investigate the influence of trailing edge bleeding on both aerodynamic and thermal performance. The cascade is composed of six vanes with a profile typical of a high pressure turbine stage. The trailing edge cooling features a pressure side cutback with film cooling slots, stiffened by evenly spaced ribs in an inline configuration. Cooling air is ejected not only through the slots but also through two rows of cooling holes placed on the pressure side, upstream of the cutback. The cascade was tested for different isentropic exit Mach numbers, ranging from M2is = 0.2 to M2is = 0.6, while varying the coolant to mainstream mass flow ratio MFR up to 2.8%. The momentum boundary layer behavior at a location close to the trailing edge, on the pressure side, was assessed by means of laser Doppler measurements. Cases with and without coolant ejection allowed us to identify the contribution of the coolant to the off the wall velocity profile. Thermochromic liquid crystals (TLC) were used to map the adiabatic film cooling effectiveness on the pressure side cooled region. As expected, the cutback effect on cooling effectiveness, compared to the other cooling rows, was dominant.

Evaluation of RANS Predictions on a Linear Nozzle Vane Cascade With Trailing Edge Cutback Film Cooling

2013 ◽  
Author(s):  
S. Ravelli ◽  
G. Barigozzi
Keyword(s):  
Film Cooling ◽  
Cooling System ◽  
Pressure Side ◽  
Trailing Edge ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Nozzle Vane ◽  
Pressure Surface ◽  
Exit Mach Number ◽  
Cooling Air

The present study concentrates on the numerical investigation of a cooled trailing edge in a linear nozzle vane cascade typical of a high-pressure turbine. The trailing edge cooling features a pressure side cutback with film cooling slots, stiffened by evenly spaced ribs in an inline configuration. Cooling air is also ejected through two rows of cooling holes placed on the pressure side, upstream of the cutback. The main goal is to evaluate the reliability of RANS predictions in such a complex cooling system. Different coolant-to-mainstream mass flow ratio values up to MFR = 2.8% were simulated at exit Mach number of M2is = 0.2. The computed performance of the trailing edge cooling scheme was compared to available measurements of: holes and cutback exit velocity and discharge behavior; boundary layer along traverses located on the pressure side, downstream of each row of cooling holes and approaching the trailing edge; adiabatic film cooling effectiveness. Special emphasis was dedicated to coolant-mainstream interaction and film cooling effectiveness over the pressure surface of the vane. Despite the steady approach, the simulations provided a reliable overview of coolant and mainstream aerodynamic features. The limitations in predicting the measured drop in cooling effectiveness toward the trailing edge were highlighted as well.

Experimental and Numerical Investigation of Trailing Edge Film Cooling by Circular Coolant Wall Jets Ejected From a Slot With Internal Rib Arrays

2003 ◽  
Author(s):  
P. Martini ◽  
A. Schulz ◽  
S. Wittig
Keyword(s):  
Film Cooling ◽  
Three Dimensional ◽  
Numerical Data ◽  
Trailing Edge ◽  
Adiabatic Wall ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Edge Features ◽  
Cooling Air

The present study concentrates on the experimental and computational investigation of a cooled trailing edge in a modern turbine blade. The trailing edge features a pressure side cutback and a slot, stiffened by two rows of evenly spaced ribs in an inline configuration. Cooling air is ejected through the slot and forms a cooling film on the trailing edge cutback region. In the present configuration the lateral spacing of the ribs equals two times their width. The height of the ribs, i.e. the height of the slot equals their width. Since the ribs are provided with fillet radii of half the slot height in size, circular coolant jets are exiting the slot tangentially to the trailing edge cutback. The adiabatic wall temperature mappings on the trailing edge cutback indicate that strong three-dimensional flow interaction between the coolant jets and the hot main flow takes place in such a way that two or more coolant jets coalesce depending on the blowing ratio. Experimental and numerical data to be presented in the present study include adiabatic film cooling effectiveness on the trailing edge cutback, the pressure distribution along the internal ribbed passage as well as slot discharge coefficients for different blowing ratios ranging from M = 0.35 to 1.1.

Experimental and Numerical Investigation of Trailing Edge Film Cooling by Circular Coolant Wall Jets Ejected From a Slot With Internal Rib Arrays

2004 ◽  
Vol 126 (2) ◽  
pp. 229-236 ◽  
Author(s):  
P. Martini ◽  
A. Schulz
Keyword(s):  
Film Cooling ◽  
Three Dimensional ◽  
Numerical Data ◽  
Trailing Edge ◽  
Adiabatic Wall ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Edge Features ◽  
Cooling Air

The present study concentrates on the experimental and computational investigation of a cooled trailing edge in a modern turbine blade. The trailing edge features a pressure side cutback and a slot, stiffened by two rows of evenly spaced ribs in an inline configuration. Cooling air is ejected through the slot and forms a cooling film on the trailing edge cutback region. In the present configuration the lateral spacing of the ribs equals two times their width. The height of the ribs, i.e., the height of the slot equals their width. Since the ribs are provided with fillet radii of half the slot height in size, circular coolant jets are exiting the slot tangentially to the trailing edge cutback. The adiabatic wall temperature mappings on the trailing edge cutback indicate that strong three-dimensional flow interaction between the coolant jets and the hot main flow takes place in such a way that two or more coolant jets coalesce depending on the blowing ratio. Experimental and numerical data to be presented in the present study include adiabatic film cooling effectiveness on the trailing edge cutback, the pressure distribution along the internal ribbed passage as well as slot discharge coefficients for different blowing ratios ranging from M=0.35 to 1.1.

A Numerical Investigation of Stator-Rotor Interaction Effects on Flow Field and Film Cooling Effectiveness in a 3D Transonic Turbine Stage With Highly Twisted Rotors

2013 ◽  
Author(s):  
Huazhao Xu ◽  
Jianhua Wang ◽  
Ting Wang
Keyword(s):  
Shock Waves ◽  
Film Cooling ◽  
Static Pressure ◽  
Pressure Fluctuations ◽  
Suction Side ◽  
Turbine Stage ◽  
Trailing Edge ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Air

To reduce aerodynamic losses and optimize turbine blade cooling designs, a comprehensive understanding of rotor-stator interaction effects on the blade aerodynamics and film cooling performance is essential. This paper focuses on the numerical analysis of the interactions between shock waves and unsteady wakes and their effects on cooling effectiveness of a highly twisted rotor within a transonic turbine stage. The parameters of the turbine stage are from the Pratt & Whitney Energy Efficient Engine (E3) program. The Realizable k-ε turbulence model was selected as the suitable turbulence model by our previous study. The investigation is conducted first by analyzing mean static pressure and the Root Mean Square (RMS) of the static pressure, followed by a detailed study of the flow field in the rotor passage at blowing ratios (Br) of 0.5, 1.0 and 1.5. Effects of the complicated interactions among shock waves, trailing edge wake shedding, and blockage of moving rotors are separated and identified individually through shock strength, vortices, and entropy production. The results show that: 1) For the stator, the shock waves emanating from the trailing edge of the neighboring stator impinging on the later part of the stator’s suction side, creating static pressure fluctuations as large as 20%. 2) For the rotor, the variation of static pressure is synchronized with the rotor passing frequency, but out of phase between the suction and pressure sides. 3) A high entropy region generated by the wake flow from the upstream trailing edge in the rotor passage intensifies and moves towards the rotor hub during the rotor passing periods. 4) Most of the cooling air injected from the rotor leading edge bends towards the suction side, and the cooling air injected from the pressure side turns towards the rotor hub. 5) An increase in the blowing ratio from Br = 0.5 to Br = 1.5 does not affect the pressure fluctuations, but does significantly increase film cooling effectiveness on the rotor pressure side. 6) The mean static pressure on the suction side of the twist blade is lower than a straight blade, indicating the benefit of producing larger torque by using twist rotors.

Pressure Side and Cutback Trailing Edge Film Cooling in a Linear Nozzle Vane Cascade at Different Mach Numbers

2011 ◽  
Author(s):  
Giovanna Barigozzi ◽  
Antonio Perdichizzi ◽  
Silvia Ravelli
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Pressure Side ◽  
Trailing Edge ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Mach Numbers ◽  
Nozzle Guide ◽  
Cooling Air ◽  
Momentum Boundary Layer

Tests on a specific designed linear nozzle guide vane cascade with trailing edge coolant ejection were carried out to investigate the influence of trailing edge bleeding on both aerodynamic and thermal performance. The cascade is composed of six vanes with a profile typical of a high pressure turbine stage. The trailing edge cooling features a pressure side cutback with film cooling slots, stiffened by evenly spaced ribs in an inline configuration. Cooling air is ejected not only through the slots but also through two rows of cooling holes placed on the pressure side, upstream of the cutback. The cascade was tested for different isentropic exit Mach numbers, ranging from M2is = 0.2 to M2is = 0.6, while varying the coolant to mainstream mass flow ratio MFR up to 2.8%. The momentum boundary layer behavior at a location close to the trailing edge, on the pressure side, was assessed by means of Laser Doppler measurements. Cases with and without coolant ejection allowed to identify the contribution of the coolant to the off the wall velocity profile. Thermochromic Liquid Crystals (TLC) were used to map adiabatic film cooling effectiveness on the pressure side cooled region. As expected, the cutback effect on cooling effectiveness, compared to the other cooling rows, was dominant.

Experiment Study of Simulated Effect of Rotor Stator Interaction: Effect of Axial Spacing and Rotor Blade Film Cooling Air Injection Ratio

2011 ◽  
Author(s):  
Murari Sridhar ◽  
B. V. S. S. S. Prasad ◽  
N. Sitaram
Keyword(s):  
Mass Flow ◽  
Film Cooling ◽  
Density Ratio ◽  
Leading Edge ◽  
Main Flow ◽  
Air Injection ◽  
Blade Surface ◽  
Trailing Edge ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness

The effect of inlet wake and air injection on blade surface temperature distribution is experimentally determined in the present paper. A flat plate with smoothly curved leading edge and a symmetric beveled trailing edge is used to produce inlet wake. Experiments are performed on a seven-airfoil linear cascade in a low speed wind tunnel at the chord Reynolds number of 5.3×105. Three blades in the middle of the cascade are provided with multiple rows of air injection holes on both pressure surface and suction surface. The distance between the trailing edge of the wake plate and leading edge of the cascade blade is kept at three axial locations, i.e. 0.25, 0.35 and 0.5 (all measured in terms of percent blade chord), at seven transverse locations for each axial location. The detailed temperature distributions on the blade surface are measured using “T-Type” thermocouples connected to a data logger. The results are obtained in terms of film cooling effectiveness for a density ratio (between the hot fluid through air injection holes and cold main flow fluid) of 1.1 and injection mass flow rates of 1.1, 2.5, 3.0 and 5.0 percent of main flow. A significant change in the film cooling effectiveness is observed with increase in the injection mass flow rate and change in the axial spacing.

Large Eddy Simulations of Film-Cooling Flows With a Micro-Ramp Vortex Generator

2011 ◽  
Author(s):  
Aaron F. Shinn ◽  
S. Pratap Vanka
Keyword(s):  
Film Cooling ◽  
Cross Flow ◽  
Vortex Generator ◽  
Vortex Pair ◽  
Large Eddy Simulations ◽  
Wind Tunnel Experiments ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Cooling Flows ◽  
Large Eddy

Large Eddy Simulations were performed to study the effect of a micro-ramp on an inclined turbulent jet interacting with a cross-flow in a film-cooling configuration. The micro-ramp vortex generator is placed downstream of the film-cooling jet. Changes in vortex structure and film-cooling effectiveness are evaluated and the genesis of the counter-rotating vortex pair in the jet is discussed. Results are reported with the jet modeled using a plenum/pipe configuration. This configuration was designed based on previous wind tunnel experiments at NASA Glenn Research Center, and the present results are meant to supplement those experiments. It is found that the micro-ramp improves film-cooling effectiveness by generating near-wall counter-rotating vortices which help entrain coolant from the jet and transport it to the surface. The pair of vortices generated by the micro-ramp are of opposite sense to the vortex pair embedded in the jet.

Sign in / Sign up

Export Citation Format

Share Document