Development of a Generalized LCF-TMF Lifing Model for a Nickel-Base Superalloy

2012 ◽  
Author(s):  
Björn Buchholz ◽  
Uwe Gampe ◽  
Tilmann Beck
Keyword(s):  
Power Generation ◽  
Life Prediction ◽  
Power Plants ◽  
Prediction Models ◽  
Low Cycle Fatigue ◽  
Turbine Blades ◽  
Combined Cycle ◽  
Nickel Base Superalloy ◽  
Nickel Base ◽  
Base Superalloy

The growing share of power generation from volatile sources such as wind and photovoltaics requires fossil fuel fired power generation units be available and capable of high load flexibility to adjust to the changing capacity of the electrical grid. Additionally, back-up units with quick start capability and energy storage technologies are needed to fill the power shortfall when volatile sources are not available. Gas turbine and combined-cycle gas and steam turbine power plants are able to meet these demands. However, safe component design for improved cycling capability, combined with optimum utilization of material regarding its mechanical properties, requires design procedures and lifing models for the complex loadings resulting from this increased volatility of power demand. Since hot gas path components like turbine blades and vanes are highly stressed by cyclic thermal and mechanical loadings, resulting Thermo-Mechanical Fatigue (TMF), life prediction models such as the classic strain-life Coffin-Manson-Basquin method do not capture the influences of thermal cycling satisfyingly. Advanced TMF prediction models are thus necessary to accurately predict the durability of hot section components. This paper addresses life prediction of the Nickel-base superalloy René 80 at elevated temperature for various loading conditions. For this purpose, isothermal Low Cycle Fatigue (LCF) and corresponding TMF tests, with various temperature ranges and thermal-mechanical phase shifts, have been performed. On this basis, a systematic approach has been developed which allows assessing the key influences on TMF life. Moreover, a generalized model for fatigue has been derived, which has the potential to predict TMF life on the basis of LCF data. The knowledge gained from the model development allows an improved life prediction and better utilization of the material capabilities. Additionally, the required number of material tests for a general insight in the materials behaviour can be reduced significantly.

Effect of Precipitation Aging Temperatures on Reheat Treated Microstructures and its Phase Stability after Long-Term Exposure in Cast Nickel Base Superalloy, Grade Inconel 738

2017 ◽  
Vol 891 ◽  
pp. 433-437 ◽  
Author(s):  
Nattapol Kontikame ◽  
Sureerat Polsilapa ◽  
Panyawat Wangyao
Keyword(s):  
Phase Stability ◽  
Power Plants ◽  
Turbine Blades ◽  
Research Work ◽  
Nickel Base Superalloy ◽  
Gamma Prime ◽  
Treatment Conditions ◽  
Nickel Base ◽  
Base Superalloy

This research work has an aim to investigate the effect of precipitation aging temperatures of 845°C, 865°C, 885°C and 905°C for 24 hours after solutioning treatment at temperature of 1145°C for 4 hours on final microstructure of cast nickel base superalloy, grade Inconel 738, which is used as a material for turbine blades in land base gas turbine engines to generate electricity in power plants. Further interesting is also extended to study and evaluate the phase stability of precipitated gamma prime particles after long-term heating at tempeatures of 900°C and 1000°C for 200 hours of all received final microstructures after various reheat treatment conditions. From all obtained results, it was found that the higher precipitation aging temperatures provided the more coarsening size of both coarse and fine gamma prime particles. Furthermore, after long-term exposure at high temperatures, this resulted in an increasing of both area density and size of gamma prime particles.

Isothermal LCF Behaviors of a NiCrAlYSi Coated Columnar-Grained Directionally Solidified Nickel Base Superalloy

2007 ◽  
Vol 353-358 ◽  
pp. 203-206
Author(s):  
Hui Chen Yu ◽  
Bin Zhong ◽  
Xue Ren Wu
Keyword(s):  
Physical Vapor Deposition ◽  
Low Cycle Fatigue ◽  
Fatigue Behavior ◽  
Turbine Blades ◽  
Strain Range ◽  
Nickel Base Superalloy ◽  
Directionally Solidified ◽  
Different Temperatures ◽  
Nickel Base ◽  
Base Superalloy

The isothermal low cycle fatigue (LCF) behaviors of a directionally solidified (DS) nickel base superalloy, coated with a NiCrAlYSi coating were studied. The study concerned NiCrAlYSi coating formed by an arc-discharged physical vapor deposition (PVD) process for protection against high-temperature corrosion and oxidation of gas turbine blades. The effect of protective coating on LCF life of coating/substrate system was investigated at high temperatures and compared with uncoated alloy. The test results show that coating has no or less effect on LCF life under high strain range and the LCF life is governed by the fatigue behavior of substrate at different temperatures. However, when strain range is smaller, crack initiation and propagation are observably affected by temperature, which leads to a shorter LCF life of coating/substrate system at 500°C and a longer LCF life at 760°C or 980°C.

A Life Prediction Model for Single-Crystal Nickel-Base Alloys Under Low-Cycle Fatigue

2020 ◽  
Author(s):  
Firat Irmak ◽  
Navindra Wijeyeratne ◽  
Taejun Yun ◽  
Ali Gordon
Keyword(s):  
Single Crystal ◽  
Gas Turbine ◽  
Life Prediction ◽  
Low Cycle Fatigue ◽  
Turbine Blades ◽  
Deformation Model ◽  
Cycle Fatigue ◽  
Nickel Base Superalloys ◽  
Nickel Base ◽  
Prediction Approach

Abstract In the development and assessment of critical gas turbine components, simulations have a crucial role. An accurate life prediction approach is needed to estimate lifespan of these components. Nickel base superalloys remain the material of choice for gas turbine blades in the energy industry. These blades are required to withstand both fatigue and creep at extreme temperatures during their usage time. Nickel-base superalloys present an excellent heat resistance at high temperatures. Presence of chromium in the chemical composition makes these alloys highly resistant to corrosion, which is critical for turbine blades. This study presents a flexible approach to combine creep and fatigue damages for a single crystal Nickel-base superalloy. Stress and strain states are used to compute life calculations, which makes this approach applicable for component level. The cumulative damage approach is utilized in this study, where dominant damage modes are capturing primary microstructural mechanism associated with failure. The total damage is divided into two distinctive modules: fatigue and creep. Flexibility is imparted to the model through its ability to emphasize the dominant damage mechanism which may vary among alloys. Fatigue module is governed by a modified version of Coffin-Manson and Basquin model, which captures the orientation dependence of the candidate material. Additionally, Robinson’s creep rupture model is applied to predict creep damage in this study. A novel crystal visco-plasticity (CVP) model is used to simulate deformation of the alloy under several different types of loading. This model has capability to illustrate the temperature-, rate-, orientation-, and history-dependence of the material. A user defined material (usermat) is created to be used in ANSYS APDL 19.0, where the CVP model is applied by User Programmable Feature (UPF). This deformation model is constructed of a flow rule and internal state variables, where the kinematic hardening phenomena is captured by back stress. Octahedral, cubic and cross slip systems are included to perform simulations in different orientations. An implicit integration process that uses Newton-Raphson iteration scheme is utilized to calculate the desired solutions. Several tensile, low-cycle fatigue (LCF) and creep experiments were conducted to inform modeling parameters for the life prediction and the CVP models.

scholarly journals Effect of Salt Coatings on Low Cycle Fatigue Behavior of Nickel -base Superalloy GTM-SU-718

2013 ◽  
Vol 55 ◽  
pp. 830-834 ◽  
Author(s):  
G.S. Mahobia ◽  
R.G. Sudhakar ◽  
Ajesh Antony ◽  
K. Chattopadhyay ◽  
N.C. Santhi Srinivas ◽  
...  
Keyword(s):  
Low Cycle Fatigue ◽  
Fatigue Behavior ◽  
Nickel Base Superalloy ◽  
Cycle Fatigue ◽  
Nickel Base ◽  
Base Superalloy
Sign in / Sign up

Export Citation Format

Share Document