Endwall Contouring and Fillet Design for Reducing Losses and Homogenizing the Outflow of a Compressor Cascade

2014 ◽  
Author(s):  
Oliver Reutter ◽  
Stefan Hemmert-Pottmann ◽  
Alexander Hergt ◽  
Eberhard Nicke
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Leading Edge ◽  
Total Pressure Loss ◽  
Wall Region ◽  
Optimized Design ◽  
Compressor Cascade ◽  
Outflow Region ◽  
Endwall Contouring ◽  
Operating Points

The following paper deals with the development of an optimized fillet and an endwall contour for reducing the total pressure loss and for homogenizing the outflow of a highly loaded cascade with a low aspect ratio. The NACA-65 K48 cascade profile without a fillet and without endwall contouring is used as a basis. Optimizations are performed using the DLR in-house tool AutoOpti and the RANS-solver TRACE. Three operating points at an inflow Mach number of 0.67 with different inflow angles are used to secure a wide operating range of the optimized design. At first only a fillet is optimized. The optimized fillet is small at the leading edge and rather high, wide and thick towards the trailing edge. It reduces the total pressure loss and homogenizes the outflow up to a blade height of 20 %. Following this a combined optimization of the endwall and the fillet is performed. The optimized contour leads to the development of a vortex, which changes the secondary flow in such a way, that the corner separation is reduced, which in turn significantly reduces the total pressure loss up to 16 % in the design operating point. The contour in the outflow region leads to a significant homogenization of the outflow in the near wall region.

Investigation on Performance of Compressor Cascade with Tubercle Leading Edge Blade

2020 ◽  
Vol 37 (3) ◽  
pp. 295-303 ◽  
Author(s):  
Tu Baofeng ◽  
Zhang Kai ◽  
Hu Jun
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Large Scale ◽  
Design Method ◽  
Leading Edge ◽  
Experimental Tests ◽  
Aerodynamic Performance ◽  
Total Pressure Loss ◽  
Compressor Cascade ◽  
Linear Compressor Cascade

AbstractIn order to improve compressor performance using a new design method, which originates from the fins on a humpback whale, experimental tests and numerical simulations were undertaken to investigate the influence of the tubercle leading edge on the aerodynamic performance of a linear compressor cascade with a NACA 65–010 airfoil. The results demonstrate that the tubercle leading edge can improve the aerodynamic performance of the cascade in the post-stall region by reducing total pressure loss, with a slight increase in total pressure loss in the pre-stall region. The tubercles on the leading edge of the blades cause the flow to migrate from the peak to the valley on the blade surface around the tubercle leading edge by the butterfly flow. The tubercle leading edge generates the vortices similar to those created by vortex generators, splitting the large-scale separation region into multiple smaller regions.

Effects of modified micro-vortex generators on aerodynamic performance in a high-load compressor cascade

2018 ◽  
Vol 233 (3) ◽  
pp. 309-323 ◽  
Author(s):  
Shan Ma ◽  
Wuli Chu ◽  
Haoguang Zhang ◽  
Xiangjun Li ◽  
Haiyang Kuang
Keyword(s):  
Secondary Flow ◽  
Pressure Loss ◽  
Total Pressure ◽  
Reverse Flow ◽  
Leading Edge ◽  
High Load ◽  
Total Pressure Loss ◽  
Vortex Generators ◽  
Compressor Cascade ◽  
Flow Loss

In the current study, the effects of micro-vortex generators on the flow characteristics of a high-load compressor cascade are investigated, and four types of micro-vortex generators including “rectangular,” “curved rectangular,” “trapezoidal,” and “curved trapezoidal” are considered and named VGR, VGCR, VGT, and VGCT separately. The calculated results show that a rising reverse flow region, which is considered a main reason for occurring stall at +8° incidence, collapses rapidly from the leading edge in the cascade. Therefore, the micro-vortex generators are all mounted on the end-wall in front of the passage to suppress the development of the secondary flow, and the stall occurrence is delayed from +8° to +11° incidence by applying VGCT. At the design condition, the VGT can make the total pressure loss decrease by 0.54%. The modified micro-vortex generators show an obvious superiority when the range of incidence is between +3° and +8°. At the stall condition, the VGCT can make the total pressure loss decrease by 9.36%. Moreover, the reduction of the secondary flow loss is considered a main goal of the adoption of micro-vortex generators which is an achievement for decreasing the total pressure loss, and the highest reduction of the secondary flow loss reaches 34.6% at the stall condition in the cascade with VGCT.

A Numerical Study of Volute Design in Centrifugal Compressor

2001 ◽  
Author(s):  
Weili Yang ◽  
Peter Grant ◽  
James Hitt
Keyword(s):  
Centrifugal Compressor ◽  
Pressure Loss ◽  
Total Pressure ◽  
Numerical Study ◽  
Flow Behavior ◽  
Numerical Results ◽  
Total Pressure Loss ◽  
Pressure Loss Coefficient ◽  
Computational Fluid Dynamics Cfd ◽  
Operating Points

Abstract Our principle goal of this study is to develop a CFD based analysis procedure that could be used to analyze the geometric tradeoffs in scroll geometry when space is limited. In the study, a full centrifugal compressor stage at four different operating points from near surge to near choke is analyzed using Computational Fluid Dynamics (CFD) and laboratory measurement. The study concentrates on scroll performance and its interaction with a vaneless diffuser and impeller. The numerical results show good agreement with test data in scroll circumferential pressure distribution at different ΛAR, total pressure loss coefficient, and pressure distortion at the tongue. The CFD analysis also predicts a reasonable choke point of the stage. The numerical results provide overall flow field in the scroll and diffuser at different operating points. From examining the flow fields, one can have a much better understanding of rather complicated flow behavior such as jet-wake mixing, and choke. One can examine total pressure loss in detail to provide crucial direction for scroll design improvement in areas such as volute tongue, volute cross-section geometry and exit conical diffuser.

Heat Transfer Enhancement for Gas Turbine Blade Leading Edge Cooling Using Curved Double-Wall/Vortex Cooling With Various Disturbing Objects

2019 ◽  
Author(s):  
Xiaojun Fan ◽  
Liang Li ◽  
Jiefeng Wang ◽  
Fan Wu
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Pressure Loss ◽  
Total Pressure ◽  
Leading Edge ◽  
Total Pressure Loss ◽  
Wall Impingement ◽  
Pin Fins ◽  
Cooling Passage ◽  
Double Wall

Abstract A new double-wall cooling configuration combined with the vortex cooling is established to study the cooling behavior for the gas turbine blade leading edge. This configuration consists of multiple nozzles, a curved inner cooling passage, a row of bridge holes and a curved outer cooling passage with 4 kinds of disturbing objects (namely smooth wall, pin-fins, dimples and protrusions). Numerical simulations are performed based on the 3D viscous steady Reynolds Averaged Navier-Stokes (RANS) equations and the k-ω turbulence model. The cooling behavior of the Double-wall/vortex cooling configuration is compared with the Double-wall/impingement cooling configuration at the same conditions. Generally, the Double-wall/vortex cooling configuration has a better cooling performance. It is found the Nusselt number of the inner surface for the Double-wall/vortex cooling configuration is 46.7% higher. However, the Double-wall/impingement cooling configuration has a smaller friction coefficient and a total pressure loss. Different disturbing objects have significant influences on the heat transfer performance of the outer surface. The Nusselt number of disturbing objects (pin-fins, dimples and protrusions) is much higher than the smooth wall, and the value is 1.27–2.22 times larger. Configuration with protrusions has the highest globally-averaged Nusselt number. For the heat transfer performance of the inner surface and the total pressure loss coefficient, disturbing objects have no obvious influence. As bridge holes row increases, the overall cooling performance is improved. The globally-averaged Nusselt number of the outer target is enhanced while the total pressure loss is reduced.

Location Effect of Boundary Layer Suction on Compressor Hub-Corner Separation

2014 ◽  
Author(s):  
Ping-Ping Chen ◽  
Wei-Yang Qiao ◽  
Karsten Liesner ◽  
Robert Meyer
Keyword(s):  
Boundary Layer ◽  
Pressure Loss ◽  
Total Pressure ◽  
Three Dimensional ◽  
Base Flow ◽  
Total Pressure Loss ◽  
Compressor Cascade ◽  
Suction Surface ◽  
Corner Separation ◽  
Boundary Layer Suction

The large secondary flow area in the compressor hub-corner region usually leads to three-dimensional separation in the passage with large amounts of total pressure loss. In this paper numerical simulations of a linear high-speed compressor cascade, consisting of five NACA 65-K48 stator profiles, were performed to analyze the flow mechanism of hub-corner separation for the base flow. Experimental validation is used to verify the numerical results. Active control of the hub-corner separation was investigated by using boundary layer suction. The influence of the selected locations of the endwall suction slot was investigated in an effort to quantify the gains of the compressor cascade performance. The results show that the optimal chordwise location should contain the development section of the three-dimensional corner separation downstream of the 3D corner separation onset. The best pitchwise location should be close enough to the vanes’ suction surface. Therefore the optimal endwall suction location is the MTE slot, the one from 50% to 75% chord at the hub, close to the blade suction surface. By use of the MTE slot with 1% suction flow ratio, the total-pressure loss is substantially decreased by about 15.2% in the CFD calculations and 9.7% in the measurement at the design operating condition.

Influence of a Novel 3D Leading Edge Geometry on the Aerodynamic Performance of Low Pressure Turbine Blade Cascade Vanes

2014 ◽  
Author(s):  
A. Asghar ◽  
W. D. E. Allan ◽  
M. LaViolette ◽  
R. Woodason
Keyword(s):  
Turbine Blade ◽  
Pressure Loss ◽  
Total Pressure ◽  
Separated Flow ◽  
Leading Edge ◽  
Low Pressure ◽  
Aerodynamic Performance ◽  
Total Pressure Loss ◽  
Low Pressure Turbine ◽  
Edge Geometry

This paper addresses the issue of aerodynamic performance of a novel 3D leading edge modification to a reference low pressure turbine blade. An analysis of tubercles found in nature and used in some engineering applications was employed to synthesize new leading edge geometry. A sinusoidal wave-like geometry characterized by wavelength and amplitude was used to modify the leading edge along the span of a 2D profile, rendering a 3D blade shape. The rationale behind using the sinusoidal leading edge was that they induce streamwise vortices at the leading edge which influence the separation behaviour downstream. Surface pressure and total pressure measurements were made in experiments on a cascade rig. These were complemented with computational fluid dynamics studies where flow visualization was also made from numerical results. The tests were carried out at low Reynolds number of 5.5 × 104 on a well-researched profile representative of conventional low pressure turbine profiles. The performance of the new 3D leading edge geometries was compared against the reference blade revealing a downstream shift in separated flow for the LE tubercle blades; however, total pressure loss reduction was not conclusively substantiated for the blade with leading edge tubercles when compared with the performance of the baseline blade. Factors contributing to the total pressure loss are discussed.

A new curvature-controlled stacking-line method for optimization design of compressor cascade considering surface smoothness

2019 ◽  
Vol 234 (5) ◽  
pp. 1061-1074
Author(s):  
Xinyi Zhang ◽  
Xiaoqing Qiang ◽  
Jinfang Teng ◽  
Wensheng Yu
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Optimization Design ◽  
Parametric Method ◽  
Total Pressure Loss ◽  
Compressor Cascade ◽  
Surface Smoothness ◽  
Line Method ◽  
Radial Curvature ◽  
Bézier Spline

The paper presents an advanced parametric method of blade stacking lines in terms of sweep and lean based on controlled curvature. To the knowledge of the authors, there is no related approach reported in open literature that uses Bezier spline as the radial curvature distribution to improve the smoothness of the blade surface; most previous studies ignored the discontinuous slopes of curvature of the parametric curves. The parametric method called curvature-controlled stacking-line method (CCSLM) is performed by changing the magnitude of the sweep or lean. A fourth Bezier spline is adopted to define the curvature of spanwise stacking line directly ensuring surface smoothness. Then, the redesign cascades are created by sectional profiles stacked along the radial stacking lines which are obtained by twice integrating the Bezier spline. Then, the advanced method is conducted to optimize a high-subsonic controlled diffusion airfoil at design point, where the blade shape is generated in terms of lean. A single-objective optimization is performed using Kriging model and genetic algorithm to optimize total pressure loss, and the optimized geometry is obtained. The optimization results show that the blade design CCSLM has significant effects on the endwall flow vortex as well as radial loading distribution. The reduction of total pressure loss and secondary flow is also observed, and the aerodynamic performance is well improved compared with the original cascade.

Impact of a Combination of Micro-Vortex Generator and Boundary Layer Suction on Performance in a High-Load Compressor Cascade

2018 ◽  
Author(s):  
Shan Ma ◽  
Wuli Chu ◽  
Haoguang Zhang ◽  
Chuanle Liu
Keyword(s):  
Boundary Layer ◽  
Pressure Loss ◽  
Total Pressure ◽  
Vortex Generator ◽  
Aerodynamic Performance ◽  
Total Pressure Loss ◽  
Control Methods ◽  
Compressor Cascade ◽  
Boundary Layer Suction ◽  
Micro Vortex Generator

The performance of a compressor cascade is considerably influenced by flow control methods. In this paper, the synergistic effects of combination between micro-vortex generators (MVG) and boundary layer suction (BLS) are discussed in a high-load compressor cascade. Seven cases, which are grouped by a kind of micro-vortex generator and boundary layer suction with three locations, are investigated to control secondary flow effects and enhance the aerodynamic performance of the compressor cascade. The MVG is mounted on the end-wall in front of the passage. The rectangle suction slot with three radial positions is installed on the blade suction surface near the trailing edge. The numerical results show that: at the design condition, the total pressure loss is effectively decreased as well as the static pressure coefficient increase when the combined MVG and SBL method (COM) is used, which is superior to MVG in an aerodynamic performance. At the stall condition, the induced vortex coming from MVG could mix the low-energy fluid and mainstream, which result in the reduced separation, and the total pressure loss decreased by 11.54% when the suction flow ratio is 1.5%. The total pressure loss decreases by 14.59% when the COM control methods are applied.

scholarly journals Investigation of Wash Fluid Preheating on the Effectiveness of Online Compressor Washing in Industrial Gas Turbines

2020 ◽  
Author(s):  
Roupa Agbadede ◽  
Biweri Kainga
Keyword(s):  
Gas Turbines ◽  
Pressure Loss ◽  
Total Pressure ◽  
Loss Coefficient ◽  
Total Pressure Loss ◽  
Compressor Cascade ◽  
Flow Angle ◽  
Pressure Loss Coefficient ◽  
Industrial Gas Turbines ◽  
Total Pressure Loss Coefficient

Abstract This study presents an investigation of wash fluid preheating on the effectiveness of online compressor washing in industrial gas turbines. Crude oil was uniformly applied on the compressor cascade blades surfaces using a roller brush, and carborundum particles were ingested into the tunnel to create accelerated fouled blades. Demineralized water was preheated to 500C using the heat coil provided in the tank. When fouled blades washed with preheated demineralized and the one without preheating were compared, it was observed that there was little or no difference in terms of total pressure loss coefficient and exit flow angle. However, when the fouled and washed cases were compared, there was a significant different in total pressure loss coefficient and exit flow angle.

Flowfield Investigation of a Compressor Cascade at High Incidence—Part 1: Pneumatic Probe Measurements

2009 ◽  
Author(s):  
Pavlos K. Zachos ◽  
Vassilios Pachidis ◽  
Bernard Charnley ◽  
Pericles Pilidis
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Incidence Angle ◽  
Axial Flow ◽  
Quantitative Measure ◽  
Operating Conditions ◽  
Total Pressure Loss ◽  
Compressor Cascade ◽  
Engine Operation ◽  
Pressure Surface

The performance prediction of axial flow compressors and turbines still relies on the stationary testing of blade cascades. Most of the blade testing studies are done for operating conditions close to the design point or in off-design areas not too far from it. However, blade performance remains unexplored at very far off-design conditions, such as windmilling, characterised by operation under extremely low mass flows and rotational speeds which, in turn, imply highly negative incidence angle values. In this paper, the flow field generated by a 3-dimensional linear compressor cascade at a highly negative incidence angle and zero rotational speed is experimentally investigated using a pneumatic miniature cobra probe. The main objective of the study is to derive the total pressure loss through the blades at such a highly negative incidence angle. An overview of the blade geometry as well as of the experimental facility is given whereas the measurement strategy and the data acquisition technique are also presented. An uncertainty study taking into account the most significant factors affecting the quality of the results has been carried out. As shown by the measurements taken at specific positions downstream of the blades, the flowfield is dominated by highly separated flows on the pressure surface, which contribute to the increased values of the total pressure loss coefficient which seems to be weakly dependent on the inlet Mach number. The quantitative measure of the pressure losses at the extremely negative incidence angle examined can be considered to be a validation platform for correspondent numerical studies of similar flow conditions. Additionally, the experimental results obtained can be used to extend the applicability of the current pressure loss models, increasing the predictive capability of the through flow numerical approaches towards far off-design areas of component or whole engine operation.

Sign in / Sign up

Export Citation Format

Share Document