Effect of Cascade Surface Roughness on Boundary Layer Flow Under Variable Conditions

Under the influence of many factors, the surface roughness of the cascade will change during turbomachinery operation, which will affect the boundary layer flow of the cascade. In this article, the effects of cascade surface roughness on boundary layer flow under variable conditions are analyzed by experiments and numerical simulation. The results show that with the increase of roughness, the total pressure loss coefficient of the cascade decreases first and then increases. The larger the Reynolds number is, the greater the total pressure loss coefficient is, and the sensitive area of loss change is changed. In the sensitive area, the roughness has a greater influence on cascade loss. There are separation bubbles at the suction front edge of smooth cascades. With the increase of roughness, the degree of turbulence increases, and the transition process is accelerated. When the roughness is between 74 and 150 μm, the separation bubble disappears and the separation loss decreases. In conclusion, the aerodynamic loss of the cascade increases with the increase of roughness, and the cascade efficiency decreases. However, roughness can restrain the flow separation and reduce the separation loss. The two have gone through a process of one and the other. When the roughness is 74 μm, the displacement thickness, momentum thickness, and shape factor at the back of the cascade are the minimum.

Very Large Eddy Simulation of Aero-Thermal Performance in Squealer Tip Gap

To improve the resolution accuracy and get deep insight into the flow structures in squealer tip gap, the Very Large Eddy Simulation (VLES) method was implemented into the commercial CFD (Computational Fluid Dynamics) solver with the User Defined Function (UDF). Based on the published experimental data, the numerical accuracy of VLES method was validated. With VLES method, the unsteady heat transfer coefficient distributions on the squealer tip and total pressure loss in the blade passage were computed. The influences of coherent vortex structures on aero-thermal performance in the squealer tip gap were analyzed. The results show that the Brown-Roshko vortices are the main driver for the formation of cavity vortex system. The direct impingement of pass-over leakage into the cavity is the main cause of high heat transfer area on the cavity floor near leading edge. The unsteady fluctuations of leakage rate through the tip gap reach about ±8% of the time-averaged value. The development of leakage vortex accounts for the major contribution of total pressure loss in the squealer tipped blade. Due to flow unsteadiness, the fluctuation of pitch-averaged total pressure loss coefficient induced by leakage vortex system reaches about ±30% of the time-averaged value. The unsteady fluctuation of pitch-averaged heat transfer coefficient on the cavity floor reaches about ±35% of the time-averaged value, while on the shroud surface it is only fluctuated by about ±10%.

Computational fluid dynamic analysis of the initiation of cerebral aneurysms

OBJECTIVE Relationships between aneurysm initiation and hemodynamic factors remain unclear since de novo aneurysms are rarely observed. Most previous computational fluid dynamics (CFD) studies have used artificially reproduced vessel geometries before aneurysm initiation for analysis. In this study, the authors investigated the hemodynamic factors related to aneurysm initiation by using angiographic images in patients with cerebral aneurysms taken before and after an aneurysm formation. METHODS The authors identified 10 cases of de novo aneurysms in patients who underwent follow-up examinations for existing cerebral aneurysms located at a different vessel. The authors then reconstructed the vessel geometry from the images that were taken before aneurysm initiation. In addition, 34 arterial locations without aneurysms were selected as control cases. Hemodynamic parameters acting on the arterial walls were calculated by CFD analysis. RESULTS In all de novo cases, the aneurysmal initiation area corresponded to the highest wall shear stress divergence (WSSD point), which indicated that there was a strong tensile force on the arterial wall at the initiation area. The other previously reported parameters did not show such correlations. Additionally, the pressure loss coefficient (PLc) was statistically significantly higher in the de novo cases (p < 0.01). The blood flow impact on the bifurcation apex, or the secondary flow accompanied by vortices, resulted in high tensile forces and high total pressure loss acting on the vessel wall. CONCLUSIONS Aneurysm initiation may be more likely in an area where both tensile forces acting on the vessel wall and total pressure loss are large.

Optimization study on the influence of little blades’ spatial position on a compressor cascade performance

To reveal the importance of little blades’ spatial position to improve the cascade performance at different condition, the pitchwise and axial direction of the little blades on the end-wall are adopted as the optimization variables to complete a double-objective optimization. Meanwhile, the three-dimensional flow field characteristics of the cascade with and without little blades are analyzed comparatively. The study found that as the optimal solutions are obtained at the three bigger incidences (3°, 5°, and 7°), the optimal position is always close to the leading edge of blade and far away from the blade suction surface, and the more intuitive design suggestions are given in this article. Moreover, at the near design conditions (−1°, 0°, and 1°), little blades increase the total pressure loss and reduce the static pressure, which are considered unsuitable for improving the cascade performance. If the stable operation range are the main performance indicators, the optimization of the little blades’ spatial position should be completed at the near stall condition (7° incidence). If the conditions with mid-range incidences (2°< i <5°) are the main performance index, the parameter optimization of little blades should be achieved at 5°. Based on the further flow field analysis of the optimization results obtained at 3°, 5°, and 7° incidences (named Opt_Act3, Opt_Act5, and Opt_Act7), the induced vortices resist the effect of axial reverse pressure gradient and pass through the blade passage, which is the main reason for the total pressure loss reduction. Appropriate spatial position of little blades not only strengthens the capability to prevent the low-energy fluids accumulating in the corner region near the end-wall, but exhibits sufficient advantage to weaken the boundary layer.

Applications of little blades in a high-load compressor cascade with leaned blade

The development of boundary layer affects the compressor cascade performance to a certain extent. Therefore, the compound lean and little blades are selected to redistribute the boundary layer, and the influences of these two flow control technologies on the axial compressor cascade performance are further studied. The calculated results showed that appropriate high pressure region on the blade suction surface near the end-wall is helpful to reduce the total pressure loss of compressor cascade, which can be achieved by positive lean technique. Meanwhile, the maximum stable operation boundary can be expanded by the application of positive leaned blade. On the other hand, the introduction of negative lean angle not only increases the total pressure loss of cascade, but reduces the stable operation range. As the little blades are introduced in the negative lean compressor cascade, the stable operation range is significantly improved by the introduction of little blades. Especially the cascade with −10° lean angle, the maximum stable operation boundary is increased from 1° to 6°. In the positive lean compressor cascade, although more low-energy fluid is accumulated on the blade suction surface near the mid-span, the little blades still show an active role in reducing the total pressure loss and expending the stable operation range, because the influence range of induced vortex reaches 30%span. The results provide a reference for improving the aerodynamic performance of compressor stator, especially when more low-energy fluid is blocked in the range near the mid-span.

Impacts of tandem configurations on the aerodynamic performance of an axial supersonic through-flow fan cascade

In the current study, the tandem blade technology is applied to an STFF tandem cascade for the first time, and a 2D STFF tandem cascade is preliminarily designed. Through the modification design of the tandem airfoils and their configuration (axial overlap, AO and percent pitch, PP), the coefficients of total pressure loss and loading are reduced by 4% and 8.58%, respectively. Furtherly, the impact of tandem configurations on the performance is parametrically investigated by numerical simulations. The results indicate that compared with AO, the performance under design incidence is more sensitive to PP except for the cases with PP exceeding a threshold value (1.15). PP dominates the loss and load by controlling the evolution of the FB wake and the shock structure of FB and RB, while AO mainly adjusts the entire shock system structure through the change of virtual shape, resulting in the variation in load distribution between FB and RB. It is worth noting that the overall loading and the total loss remain unchanged with increasing AO except for the tandem configurations (PP=1.05, AO≤−0.01), which make the flow structure in the gap region undergo a fundamental change. With the optimal tandem configuration (PP=1.05, AO=−0.01) and the modified tandem blades (The ratios of chord length and camber for FB over RB is 0.67 and 0.5, respectively), the total pressure loss coefficient is further reduced by 19.7% in comparison with the preliminary tandem design.

An Investigation of the Tapered Strut On Aerodynamic Performance of the Exhaust Diffuser Under Different Swirls

The exhaust diffuser with different struts was numerically calculated by solving three-dimensional Reynolds-Averaged Navier-Stokes (RANS). The flow process and flow loss mechanism in the diffuser were analyzed, the influence of two different structures of tapered struts on the aerodynamic performance of the exhaust diffuser under different inlet pre-swirls was explored, and the aerodynamic performance of the exhaust diffuser with tapered struts was compared with a conventional exhaust diffuser with linear struts. The results show that, compared with the conventional linear strut, under different inlet pre-swirls, two different tapered struts can both weaken the flow separation in the exhaust diffuser, thereby reducing the total pressure loss. When the inlet pre-swirl is greater than 0.35, the total pressure loss coefficient of the exhaust diffuser with structure-C tapered struts decreases by up to 0.07. The two types of tapered struts also change the flow structure at the exhaust diffuser outlet, which affects the uniformity of the outlet airflow, and then affect the static pressure recovery coefficient. Under different inlet pre-swirls, two types of tapered struts can be effective to increase the static pressure recovery coefficient of the exhaust diffuser, for the exhaust diffuser with structure-C tapered struts, the static pressure recovery coefficient can be increased by up to 0.065, relative increase of 20%. The research in this paper shows that the tapered structure can significantly improve the aerodynamic performance of the exhaust diffuser under different inlet pre-swirls.

Выбор геометрических характеристик фронтового устройства и длины камеры сгорания прямоточного типа

A method has been developed for selecting the geometric characteristics of the front and the length of the direct-flow combustion chamber. Afterburner combustion chambers are of the ramjet type and are used for a short-term increase in the thrust of a gas turbine engine during takeoff, for overcoming the sound barrier by an aircraft and for flying at supersonic speed, and for making maneuvers. As part of ramjet engines, ramjet combustion chambers are used as the main combustion chambers in which the process of fuel combustion and heat supply to the working fluid is ensured. The developed method for selecting the geometric characteristics consists in optimizing the main operating characteristics of the combustion chamber. Mathematical models are proposed for describing the dependence of the total pressure loss, the combustion efficiency and the range of stable operation of the combustion chamber against the parameters of the flow at the inlet to the combustion chamber and the geometric characteristics of the front device and the length of the combustion chamber. The analysis of the dependences of the combustion chamber working characteristics on the geometric characteristics of the front-line device and its length is carried out. As a result of the analysis of mathematical models, a list of the main geometric characteristics of the front device was determined, on which the total pressure loss, the combustion efficiency and the range of stable operation of the combustion chamber depend. Optimization parameters, optimization criterion and limits for solving the optimization problem are determined. As an implementation of the optimization method, it is proposed to use a diagram of the combustion chamber performance in the coordinates of the optimization parameters. The developed method makes it possible to ensure the optimal basic operating characteristics of the combustion chamber - total pressure loss, combustion efficiency and combustion stability limits.