Location Effect of Boundary Layer Suction on Compressor Hub-Corner Separation

2014 ◽  
Author(s):  
Ping-Ping Chen ◽  
Wei-Yang Qiao ◽  
Karsten Liesner ◽  
Robert Meyer
Keyword(s):  
Boundary Layer ◽  
Pressure Loss ◽  
Total Pressure ◽  
Three Dimensional ◽  
Base Flow ◽  
Total Pressure Loss ◽  
Compressor Cascade ◽  
Suction Surface ◽  
Corner Separation ◽  
Boundary Layer Suction

The large secondary flow area in the compressor hub-corner region usually leads to three-dimensional separation in the passage with large amounts of total pressure loss. In this paper numerical simulations of a linear high-speed compressor cascade, consisting of five NACA 65-K48 stator profiles, were performed to analyze the flow mechanism of hub-corner separation for the base flow. Experimental validation is used to verify the numerical results. Active control of the hub-corner separation was investigated by using boundary layer suction. The influence of the selected locations of the endwall suction slot was investigated in an effort to quantify the gains of the compressor cascade performance. The results show that the optimal chordwise location should contain the development section of the three-dimensional corner separation downstream of the 3D corner separation onset. The best pitchwise location should be close enough to the vanes’ suction surface. Therefore the optimal endwall suction location is the MTE slot, the one from 50% to 75% chord at the hub, close to the blade suction surface. By use of the MTE slot with 1% suction flow ratio, the total-pressure loss is substantially decreased by about 15.2% in the CFD calculations and 9.7% in the measurement at the design operating condition.

Impact of a Combination of Micro-Vortex Generator and Boundary Layer Suction on Performance in a High-Load Compressor Cascade

2018 ◽  
Author(s):  
Shan Ma ◽  
Wuli Chu ◽  
Haoguang Zhang ◽  
Chuanle Liu
Keyword(s):  
Boundary Layer ◽  
Pressure Loss ◽  
Total Pressure ◽  
Vortex Generator ◽  
Aerodynamic Performance ◽  
Total Pressure Loss ◽  
Control Methods ◽  
Compressor Cascade ◽  
Boundary Layer Suction ◽  
Micro Vortex Generator

The performance of a compressor cascade is considerably influenced by flow control methods. In this paper, the synergistic effects of combination between micro-vortex generators (MVG) and boundary layer suction (BLS) are discussed in a high-load compressor cascade. Seven cases, which are grouped by a kind of micro-vortex generator and boundary layer suction with three locations, are investigated to control secondary flow effects and enhance the aerodynamic performance of the compressor cascade. The MVG is mounted on the end-wall in front of the passage. The rectangle suction slot with three radial positions is installed on the blade suction surface near the trailing edge. The numerical results show that: at the design condition, the total pressure loss is effectively decreased as well as the static pressure coefficient increase when the combined MVG and SBL method (COM) is used, which is superior to MVG in an aerodynamic performance. At the stall condition, the induced vortex coming from MVG could mix the low-energy fluid and mainstream, which result in the reduced separation, and the total pressure loss decreased by 11.54% when the suction flow ratio is 1.5%. The total pressure loss decreases by 14.59% when the COM control methods are applied.

Applications of little blades in a high-load compressor cascade with leaned blade

2021 ◽  
pp. 095440622110164
Author(s):  
Shan Ma ◽  
Xiaolin Sun
Keyword(s):  
Boundary Layer ◽  
Pressure Loss ◽  
Total Pressure ◽  
Active Role ◽  
Low Energy ◽  
Total Pressure Loss ◽  
Stable Operation ◽  
Compressor Cascade ◽  
Suction Surface ◽  
Lean Angle

The development of boundary layer affects the compressor cascade performance to a certain extent. Therefore, the compound lean and little blades are selected to redistribute the boundary layer, and the influences of these two flow control technologies on the axial compressor cascade performance are further studied. The calculated results showed that appropriate high pressure region on the blade suction surface near the end-wall is helpful to reduce the total pressure loss of compressor cascade, which can be achieved by positive lean technique. Meanwhile, the maximum stable operation boundary can be expanded by the application of positive leaned blade. On the other hand, the introduction of negative lean angle not only increases the total pressure loss of cascade, but reduces the stable operation range. As the little blades are introduced in the negative lean compressor cascade, the stable operation range is significantly improved by the introduction of little blades. Especially the cascade with −10° lean angle, the maximum stable operation boundary is increased from 1° to 6°. In the positive lean compressor cascade, although more low-energy fluid is accumulated on the blade suction surface near the mid-span, the little blades still show an active role in reducing the total pressure loss and expending the stable operation range, because the influence range of induced vortex reaches 30%span. The results provide a reference for improving the aerodynamic performance of compressor stator, especially when more low-energy fluid is blocked in the range near the mid-span.

Corner Separation Control in a Highly Loaded Compressor Cascade Using Plasma Aerodynamic Actuation

2012 ◽  
Author(s):  
Yun Wu ◽  
Xiao-hu Zhao ◽  
Ying-hong Li ◽  
Jun Li
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Total Pressure Loss ◽  
Separation Control ◽  
Compressor Cascade ◽  
Control Effect ◽  
Suction Surface ◽  
Corner Separation ◽  
Pressure Loss Coefficient ◽  
Highly Loaded

Corner separation, which forms over the suction surface and endwall corner of a blade passage, causes significant total pressure loss in highly loaded compressors. Plasma flow control, based on the plasma aerodynamic actuation, is a novel active flow control technique to improve aircrafts’ aerodynamic characteristics and propulsion efficiency. This paper reports computational and experimental results on using three types of plasma aerodynamic actuation (PAA) to control the corner separation in a highly loaded, low speed, linear compressor cascade. Reynolds-Averaged Navier-Stokes simulations were performed to optimize the PAA arrangement. The PAA was generated by a microsecond or nanosecond dielectric barrier discharge in wind tunnel experiments. The total pressure loss coefficient distribution was adopted to evaluate the corner separation control effect. The control effect of pitch-wise PAA on the endwall, in terms of relative reduction of the pitch-wise averaged total pressure loss coefficient in the wake, is much better than that of stream-wise PAA on the suction surface. When both pitch-wise PAA on the endwall and stream-wise PAA on the suction surface are turned on simultaneously, the control effect is the best among all three types of PAA. The main effect of pitch-wise PAA on the endwall is to inhibit the crossflow from neighboring pressure surface to the suction surface, whilest the main effect of stream-wise PAA on the suction surface is to inhibit the boundary layer accumulation and separation. Compared to microsecond discharge PAA, nanosecond discharge PAA is more effective at higher freestream velocity. The mechanisms for nanosecond discharge and microsecond discharge PAA are different for corner separation control.

Effects of segmented layer suction and micro-vortex generator on a high-load compressor cascade performance

2021 ◽  
pp. 095440622098050
Author(s):  
Shan Ma ◽  
Wuli Chu ◽  
Xiaolin Sun ◽  
Zhengtao Guo ◽  
Song Yan
Keyword(s):  
Boundary Layer ◽  
Pressure Loss ◽  
Total Pressure ◽  
Vortex Generator ◽  
Total Pressure Loss ◽  
Compressor Cascade ◽  
Boundary Layer Suction ◽  
Axial Location ◽  
Micro Vortex Generator ◽  
Suction Slot

The axial location of full-span boundary layer suction is studied to explore the influences of suction slot on the cascade performance. At the design condition, the slot with 50% axial location shows a superior capability to reduce the total pressure loss. At the near stall condition, the more upstream of the suction slot is moved, the more total pressure loss is reduced, and the suction slot with a location of 0.7 axial chord length cannot effectively reduces the total pressure loss in all conditions. Moreover, a rearranged segmented suction slot according to the distribution characteristics of the flow reversal region is developed and compared with full-span boundary layer suction. The segmented suction slot shows significant advantages in delaying the stall occurrence, and the stall point is delayed from 7.9° to 10.0° compared with the baseline. According to a quantitative analysis method selected to measure the performances of flow control technologies, the wake loss is significantly reduced by the segmented suction slot. Finally, a set of micro-vortex generator is introduced in the cascade with a segmented suction slot, and the conclusion indicates that the portion near the end-wall is very effective to reduce the flow loss.

Understanding of Secondary Loss Structures in a Multi-Stage Transonic Compressor Using DES

2016 ◽  
Author(s):  
Donghyun Kim ◽  
Changmin Son ◽  
Kuisoon Kim
Keyword(s):  
Flow Separation ◽  
Pressure Loss ◽  
Total Pressure ◽  
Three Dimensional ◽  
Total Pressure Loss ◽  
Suction Surface ◽  
Corner Region ◽  
Transonic Compressor ◽  
Multi Stage ◽  
Rans Analysis

In the present study, a multi-stage transonic compressor has been analyzed to investigate secondary loss structures and flow interactions in the corner region where the hub endwall and blade suction surface meet. The Detached Eddy Simulation (DES) approach is used successfully with the Shear Stress Transport (SST) turbulence model to directly resolve the eddy structure in the separated region. The SST-DES results for a transonic three stage axial compressor are compared with a RANS analysis obtained using ANSYS CFX. The present analysis indicates that the DES is better in simulating secondary losses and vortex structures than the RANS. With the DES, a large three-dimensional separation is predicted in the stator suction surface and hub endwall compared to the RANS prediction. The flow separation affects adversely the loss characteristics such as increases in the entropy and total pressure loss. The DES analysis indicates that the secondary flow phenomenon of the stator rows is apparent in all stages. It is observed to predict two distinct vortices induced by a three dimensional flow separation in the region adjacent to the suction surface and trailing edge of the last stage stator near the hub endwall. For the front two stages, the DES also predicts strong vortices and flow separation in the same corner region while the RANS analysis fails to predict them clearly. The total pressure loss prediction is concerned, the DES analysis predicts significantly larger than the RANS analysis in the region where the hub corner separation occurs. The DES is also found to predict a periodic fluctuations in the entropy, leading to the instantaneous efficiency variations with maximum differences of about 10% compared with the RANS solutions.

scholarly journals The Effect of Inlet Boundary Layer Thickness on the Flow Within an Annular S-Shaped Duct

1998 ◽  
Author(s):  
Toyotaka Sonoda ◽  
Toshiyuki Arima ◽  
Mineyasu Oana
Keyword(s):  
Boundary Layer ◽  
Flow Pattern ◽  
Pressure Loss ◽  
Total Pressure ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Vortex Pair ◽  
Separated Flow ◽  
Total Pressure Loss ◽  
Centrifugal Impeller

Experimental and numerical investigations were carried out to gain a better understanding of the flow characteristics within an annular S-shaped duct, including the effect of the inlet boundary layer (IBL) on the flow. A duct with six struts and the same geometry as that used to connect compressor spools on our experimental small two-spool turbofan engine was investigated. A curved downstream annular passage with a similar meridional flow path geometry to that of the centrifugal compressor has been fitted at the exit of S-shaped duct. Two types of the IBL (i.e. thin and thick IBL) were used. Results showed that large differences of flow pattern were observed at the S-Shaped duct exit between two types of the IBL, though the value of “net” total pressure loss has not been remarkably changed. According to “overall” total pressure loss, which includes the IBL loss, the total pressure loss was greatly increased near the hub as compared to that for a thin one. For the thick IBL, a vortex pair related to the hub-side horseshoe vortex and the separated flow found at the strut trailing edge has been clearly captured in the form of the total pressure loss contours and secondary flow vectors, experimentally and numerically. The high-pressure loss regions on either side of the strut wake near the hub may act on a downstream compressor as a large inlet distortion, and strongly affect the downstream compressor performance. There is a much-distorted three-dimensional flow pattern at the exit of S-Shaped duct. This means that the aerodynamic sensitivity of S-Shaped duct to the IBL thickness is very high. Therefore, sufficient carefulness is needed to design not only downstream aerodynamic component (for example centrifugal impeller) but also upstream aerodynamic component (LPC OGV).

Performance Evaluation of Linear Turbine Cascades Using Three-Dimensional Viscous Flow Calculations

1985 ◽  
Vol 107 (4) ◽  
pp. 969-975 ◽  
Author(s):  
J. Moore ◽  
J. G. Moore
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Three Dimensional ◽  
Surface Flow ◽  
Total Pressure Loss ◽  
Suction Surface ◽  
Cross Sectional ◽  
High Loss ◽  
Flow Development ◽  
Turbine Cascades

The overall performance of two geometrically similar linear turbine cascades is calculated using an elliptic flow program. The increase in the mass-averaged total pressure loss is calculated within and downstream of the cascades and the results show good agreement with the measured values. The buildup and decay of the secondary kinetic energy are also shown; measurements are available for one of the cascades near and downstream of the trailing edge and these are in close agreement with the calculated values. Details of the flow development are also compared with measurements. Calculated velocity vectors near the endwall show the overturning revealed by surface flow visualization and similarly near the suction surface the strong spanwise flow is well calculated. Calculated contours of total pressure loss in cross-sectional planes confirm the important interaction of the passage vortex with the profile boundary layer at midspan. Regions of high loss near midspan are calculated downstream of both cascades; this three-dimensional flow development is followed in the calculations.

Non-Axisymmetric Endwall Contouring in a Compressor Cascade With Tip Gap

2014 ◽  
Author(s):  
Mahesh K. Varpe ◽  
A. M. Pradeep
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Three Dimensional ◽  
Axial Flow ◽  
Tip Clearance ◽  
Total Pressure Loss ◽  
Compressor Cascade ◽  
Flow Solver ◽  
Pressure Loss Coefficient ◽  
Flow Compressor

This paper describes the design of a non-axisymmetric hub contouring in a shroudless axial flow compressor cascade operating at near stall condition. Although, an optimum tip clearance reduces the total pressure loss, further minimization of the losses using hub contouring was achieved. The design methodology presented here combines an evolutionary principle with a three-dimensional CFD flow solver to generate different geometric profiles of the hub systematically. The total pressure loss coefficient was used as a single objective function to guide the search process for the optimum hub geometry. The resulting three dimensionally complex hub promises considerable benefits discussed in detail in this paper. A reduction of 15.2% and 16.23% in the total pressure loss and secondary kinetic energy, respectively, was achieved in the wake. The blade loading was observed to improve by about 4.53%. Other complementary benefits are also listed in the paper. The results confirm that non-axisymmetric contouring is an effective method for reducing the losses and thereby improving the performance of the cascade.

scholarly journals Wake Mixing Improvements in a Linear Compressor Cascade With Crenulated Trailing Edges

1990 ◽  
Author(s):  
J. L. Veesart ◽  
P. I. King ◽  
W. C. Elrod ◽  
A. J. Wennerstrom
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Total Pressure Loss ◽  
Compressor Cascade ◽  
Suction Surface ◽  
Trailing Edge ◽  
Turbine Engine ◽  
Pressure Surface ◽  
Trailing Edges ◽  
Linear Compressor Cascade

Trailing edge crenulations offer one possible way of energizing the trailing edge wakes from a gas turbine engine compressor blade by creating small vortices as a result of the pressure differential between the suction surface and pressure surface. The effect of crenulated trailing edges on wake dissipation and mixed-out total pressure loss in a linear, subsonic, compressor cascade was investigated for three low aspect ratio blade configurations: one with no crenulations and two others with large and small crenulation patterns, respectively. The effect of crenulations was to improve the wake mixing and reduce the velocity deficit. larger crenulations dissipated the wake most rapidly, and both crenulation configurations offered an improvement in total pressure loss and some improvement in flow turning.

The Effects of Freestream Turbulence on the Profile Boundary Layer and Losses in a Compressor Cascade

1984 ◽  
Author(s):  
R. L. Evans
Keyword(s):  
Boundary Layer ◽  
Pressure Loss ◽  
Total Pressure ◽  
Boundary Layer Separation ◽  
Skin Friction Coefficient ◽  
Total Pressure Loss ◽  
Freestream Turbulence ◽  
Compressor Cascade ◽  
Deviation Angle ◽  
Displacement Thickness

The turbulent profile boundary layer on a one-foot chord compressor cascade blade has been measured with varying levels of freestream turbulence. Increased levels of freestream turbulence were found to increase the fullness of the velocity profiles, with a consequent decrease in displacement thickness and an increase in the skin friction coefficient. A small increase in freestream turbulence causes the cascade total-pressure loss to increase initially, while at the higher turbulence levels boundary layer separation was delayed, resulting in a decrease in the total-pressure loss and deviation angle.

Sign in / Sign up

Export Citation Format

Share Document