Numerical Investigation on the Heat Transfer Enhancement due to Coolant Extraction on the Cold Side of Film Cooling Holes

2014 ◽  
Author(s):  
A. Andreini ◽  
G. Caciolli ◽  
R. Da Soghe ◽  
B. Facchini ◽  
L. Mazzei
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Fluid Dynamic ◽  
Numerical Approach ◽  
Test Case ◽  
Cold Side ◽  
Engine Design ◽  
Starting Point ◽  
Sst Model ◽  
Film Cooling Holes

Film cooling represents one the most widely-used cooling techniques for hot gas path components. In particular, effusion cooling has recently become an important focus of attention in the context of aero-engine design due to its high cooling performance. Notwithstanding the huge amount of work dedicated to the heat transfer on the hot side of effusion cooling plates, it has been demonstrated that up to 30 % of the total cooling effectiveness of a typical effusion cooling configuration can be ascribed to cold side convective cooling. Nevertheless, in open literature it is possible to notice a lack of knowledge as far as this topic is concerned. This paper describes a numerical activity aimed at investigating the phenomenology of the heat transfer at the entrance of film cooling holes. First of all the accuracy of the numerical approach has been validated through a comparison of enhancement factor measurements on a test case available in literature. Steady state RANS simulations have been performed, modeling turbulence by means of the k–ω SST model. The use of a transition model has been taken into account, since in these configurations the transitional behavior of the boundary layer has been highlighted in literature. Subsequently, the attention has been turned to the comprehension of the phenomena involved in the heat transfer augmentation, focusing the attention to the influence of fluid dynamic parameters such as suction ratio and Reynolds number. A good agreement has been highlighted with experimental data, therefore this work provides a starting point for future investigations on more representative configurations.

IMPROVING THE FILM COOLING PERFORMANCE OF A TURBINE ENDWALL WITH MULTI-FIDELITY MODELING CONSIDERING CONJUGATE HEAT TRANSFER

2021 ◽  
pp. 1-20
Author(s):  
Hongyan Bu ◽  
Yufeng Yang ◽  
Liming Song ◽  
Jun Li
Keyword(s):  
Heat Transfer ◽  
Design Optimization ◽  
Film Cooling ◽  
Conjugate Heat Transfer ◽  
Inlet Temperature ◽  
High Fidelity ◽  
Cooling Performance ◽  
Fine Mesh ◽  
Film Cooling Holes ◽  
Component Temperature

Abstract The gas turbine endwall is bearing extreme thermal loads with the rapid increase of turbine inlet temperature. Therefore, the effective cooling of turbine endwalls is of vital importance for the safe operation of turbines. In the design of endwall cooling layouts, numerical simulations based on conjugate heat transfer (CHT) are drawing more attention as the component temperature can be predicted directly. However, the computation cost of high-fidelity CHT analysis can be high and even prohibitive especially when there are many cases to evaluate such as in the design optimization of cooling layout. In this study, we established a multi-fidelity framework in which the data of low-fidelity CHT analysis was incorporated to help the building of a model that predicts the result of high-fidelity simulation. Based upon this framework, multi-fidelity design optimization of a validated numerical turbine endwall model was carried out. The high and low fidelity data were obtained from the computation of fine mesh and coarse mesh respectively. In the optimization, the positions of the film cooling holes were parameterized and controlled by a shape function. With the help of multi-fidelity modeling and sequentially evaluated designs, the cooling performance of the model endwall was improved efficiently.

Numerical Study on Flow and Heat Transfer of a Cooled First Stage Vane of a Gas Turbine

2016 ◽  
Author(s):  
Lv Ye ◽  
Zhao Liu ◽  
Xiangyu Wang ◽  
Zhenping Feng
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Film Cooling ◽  
Numerical Study ◽  
Coolant Flow ◽  
The Other ◽  
Edge Region ◽  
Flow Rates ◽  
Flow And Heat Transfer ◽  
Film Cooling Holes

This paper presents a numerical simulation of composite cooling on a first stage vane of a gas turbine, in which gas by fixed composition mixture is adopted. To investigate the flow and heat transfer characteristics, two internal chambers which contain multiple arrays of impingement holes are arranged in the vane, several arrays of pin-fins are arranged in the trailing edge region, and a few arrays of film cooling holes are arranged on the vane surfaces to form the cooling film. The coolant enters through the shroud inlet, and then divided into two parts. One part is transferred into the chamber in the leading edge region, and then after impinging on the target surfaces, it proceeds further to go through the film cooling holes distributed on the vane surface, while the other part enters into the second chamber immediately and then exits to the mainstream in two ways to effectively cool the other sections of the vane. In this study, five different coolant flow rates and six different inlet pressure ratios were investigated. All the cases were performed with the same domain grids and same boundary conditions. It can be concluded that for the internal surfaces, the heat transfer coefficient changes gradually with the coolant flow rate and the inlet total pressure ratio, while for the external surfaces, the average cooling effectiveness increases with the increase of coolant mass flow rates while decreases with the increase of the inlet stagnation pressure ratios within the study range.

Computational Analysis of Conjugate Heat Transfer and Particulate Deposition on a High Pressure Turbine Vane

2009 ◽  
Author(s):  
Weiguo Ai ◽  
Thomas H. Fletcher
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Conjugate Heat Transfer ◽  
Particle Method ◽  
Experimental Results ◽  
Turbine Vane ◽  
Particulate Deposition ◽  
Cooling Hole ◽  
Lagrangian Particle Method ◽  
Film Cooling Holes

Numerical computations were conducted to simulate flyash deposition experiments on gas turbine disk samples with internal impingement and film cooling using a CFD code (FLUENT). The standard k-ω turbulence model and RANS were employed to compute the flow field and heat transfer. The boundary conditions were specified to be in agreement with the conditions measured in experiments performed in the BYU Turbine Accelerated Deposition Facility (TADF). A Lagrangian particle method was utilized to predict the ash particulate deposition. User-defined subroutines were linked with FLUENT to build the deposition model. The model includes particle sticking/rebounding and particle detachment, which are applied to the interaction of particles with the impinged wall surface to describe the particle behavior. Conjugate heat transfer calculations were performed to determine the temperature distribution and heat transfer coefficient in the region close to the film-cooling hole and in the regions further downstream of a row of film-cooling holes. Computational and experimental results were compared to understand the effect of film hole spacing, hole size and TBC on surface heat transfer. Calculated capture efficiencies compare well with experimental results.

scholarly journals Heat Transfer on a Film-Cooled Rotating Blade

1999 ◽  
Author(s):  
Vijay K. Garg
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Three Dimensional ◽  
Leading Edge ◽  
Tip Clearance ◽  
Navier Stokes ◽  
Film Cooling Effectiveness ◽  
Film Cooling Holes

A multi-block, three-dimensional Navier-Stokes code has been used to compute heat transfer coefficient on the blade, hub and shroud for a rotating high-pressure turbine blade with 172 film-cooling holes in eight rows. Film cooling effectiveness is also computed on the adiabatic blade. Wilcox’s k-ω model is used for modeling the turbulence. Of the eight rows of holes, three are staggered on the shower-head with compound-angled holes. With so many holes on the blade it was somewhat of a challenge to get a good quality grid on and around the blade and in the tip clearance region. The final multi-block grid consists of 4784 elementary blocks which were merged into 276 super blocks. The viscous grid has over 2.2 million cells. Each hole exit, in its true oval shape, has 80 cells within it so that coolant velocity, temperature, k and ω distributions can be specified at these hole exits. It is found that for the given parameters, heat transfer coefficient on the cooled, isothermal blade is highest in the leading edge region and in the tip region. Also, the effectiveness over the cooled, adiabatic blade is the lowest in these regions. Results for an uncooled blade are also shown, providing a direct comparison with those for the cooled blade. Also, the heat transfer coefficient is much higher on the shroud as compared to that on the hub for both the cooled and the uncooled cases.

Effect of Internal Crossflow Velocity on Film Cooling Effectiveness: Part II — Compound Angle Shaped Holes

2017 ◽  
Author(s):  
John W. McClintic ◽  
Joshua B. Anderson ◽  
David G. Bogard ◽  
Thomas E. Dyson ◽  
Zachary D. Webster
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Film Cooling ◽  
Velocity Ratio ◽  
Injection Rate ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Crossflow Velocity ◽  
Film Cooling Holes ◽  
Compound Angle

In gas turbine engines, film cooling holes are commonly fed with an internal crossflow, the magnitude of which has been shown to have a notable effect on film cooling effectiveness. In Part I of this study, as well as in a few previous studies, the magnitude of internal crossflow velocity was shown to have a substantial effect on film cooling effectiveness of axial shaped holes. There is, however, almost no data available in the literature that shows how internal crossflow affects compound angle shaped film cooling holes. In Part II, film cooling effectiveness, heat transfer coefficient augmentation, and discharge coefficients were measured for a single row of compound angle shaped film cooling holes fed by internal crossflow flowing both in-line and counter to the span-wise direction of coolant injection. The crossflow-to-mainstream velocity ratio was varied from 0.2–0.6 and the injection velocity ratio was varied from 0.2–1.7. It was found that increasing the magnitude of the crossflow velocity generally caused degradation of the film cooling effectiveness, especially for in-line crossflow. An analysis of jet characteristic parameters demonstrated the importance of crossflow effects relative to the effect of varying the film cooling injection rate. Heat transfer coefficient augmentation was found to be primarily dependent on injection rate, although for in-line crossflow, increasing crossflow velocity significantly increased augmentation for certain conditions.

scholarly journals A Three-Dimensional Coupled Internal/External Simulation of a Film-Cooled Turbine Vane

1999 ◽  
Author(s):  
James D. Heidmann ◽  
David L. Rigby ◽  
Ali A. Ameri
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Film Cooling ◽  
Three Dimensional ◽  
High Heat ◽  
Operating Conditions ◽  
High Heat Flux ◽  
Nasa Lewis Research ◽  
Turbine Vane ◽  
Film Cooling Holes

A three-dimensional Navier-Stokes simulation has been performed for a realistic film-cooled turbine vane using the LeRC-HT code. The simulation includes the flow regions inside the coolant plena and film cooling holes in addition to the external flow. The vane is the subject of an upcoming NASA Lewis Research Center experiment and has both circular cross-section and shaped film cooling holes. This complex geometry is modeled using a multi-block grid which accurately discretizes the actual vane geometry including shaped holes. The simulation matches operating conditions for the planned experiment and assumes periodicity in the spanwise direction on the scale of one pitch of the film cooling hole pattern. Two computations were performed for different isothermal wall temperatures, allowing independent determination of heat transfer coefficients and film effectiveness values. The results indicate separate localized regions of high heat flux in the showerhead region due to low film effectiveness and high heat transfer coefficient values, while the shaped holes provide a reduction in heat flux through both parameters. Hole exit data indicate rather simple skewed profiles for the round holes, but complex profiles for the shaped holes with mass fluxes skewed strongly toward their leading edges.

Improving the Film Cooling Performance of a Turbine Endwall With Multi-Fidelity Modeling Considering Conjugate Heat Transfer

2021 ◽  
Author(s):  
Hongyan Bu ◽  
Yufeng Yang ◽  
Liming Song ◽  
Jun Li
Keyword(s):  
Heat Transfer ◽  
Design Optimization ◽  
Film Cooling ◽  
Conjugate Heat Transfer ◽  
Inlet Temperature ◽  
High Fidelity ◽  
Cooling Performance ◽  
Fine Mesh ◽  
Film Cooling Holes ◽  
Component Temperature

Abstract The gas turbine endwall is bearing extreme thermal loads with the rapid increase of turbine inlet temperature. Therefore, the effective cooling of turbine endwalls is of vital importance for the safe operation of turbines. In the design of endwall cooling layouts, numerical simulations based on conjugate heat transfer (CHT) are drawing more attention as the component temperature can be predicted directly. However, the computation cost of high-fidelity CHT analysis can be high and even prohibitive especially when there are many cases to evaluate such as in the design optimization of cooling layout. In this study, we established a multi-fidelity framework in which the data of low-fidelity CHT analysis was incorporated to help the building of a model that predicts the result of high-fidelity simulation. Based upon this framework, multi-fidelity design optimization of a validated numerical turbine endwall model was carried out. The high and low fidelity data were obtained from the computation of fine mesh and coarse mesh respectively. In the optimization, the positions of the film cooling holes were parameterized and controlled by a shape function. With the help of multi-fidelity modeling and sequentially evaluated designs, the cooling performance of the model endwall was improved efficiently.

Heat Transfer Coefficient Measurements of Film-Cooling Holes With Expanded Exits

1998 ◽  
Author(s):  
M. Gritsch ◽  
A. Schulz ◽  
S. Wittig
Keyword(s):  
Heat Transfer ◽  
Mach Number ◽  
Film Cooling ◽  
Cylindrical Hole ◽  
Superposition Method ◽  
Transfer Coefficients ◽  
Cooling Performance ◽  
Heat Transfer Coefficients ◽  
Film Cooling Holes ◽  
Injection Location

Detailed measurements of heat transfer coefficients in the nearfield of three different film-cooling holes are presented. The hole geometries investigated include a cylindrical hole and two holes with a diffuser shaped exit portion (i.e. a fan-shaped and a laidback fanshaped hole). They were tested over a range of blowing ratios M = 0.25…1.75 at an external crossflow Mach number of 0.6 and a coolant-to-mainflow density ratio of 1.85. Additionally, the effect of the internal coolant supply Mach number is addressed. Temperatures of the diabatic surface downstream of the injection location are measured by means of an infrared camera system. They are used as boundary conditions for a finite element analysis to determine surface heat fluxes and heat transfer coefficients. The superposition method is applied to evaluate the overall film-cooling performance of the hole geometries investigated. As compared to the cylindrical hole, both expanded holes show significantly lower heat transfer coefficients downstream of the injection location, particularly at high blowing ratios. The laidback fanshaped hole provides a better lateral spreading of the injected coolant than the fanshaped hole which leads to lower laterally averaged heat transfer coefficients. Coolant passage crossflow Mach number affects the flowfield of the jet being ejected from the hole and, therefore, has an important impact on film-cooling performance.

A Novel Antivortex Turbine Film-Cooling Hole Concept

2008 ◽  
Vol 130 (3) ◽  
Author(s):  
James D. Heidmann ◽  
Srinath Ekkad
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Circular Cross Section ◽  
Round Hole ◽  
Net Heat Flux ◽  
Cooling Hole ◽  
Film Cooling Holes

A novel turbine film-cooling hole shape has been conceived and designed at NASA Glenn Research Center. This “antivortex” design is unique in that it requires only easily machinable round holes, unlike shaped film-cooling holes and other advanced concepts. The hole design is intended to counteract the detrimental vorticity associated with standard circular cross-section film-cooling holes. This vorticity typically entrains hot freestream gas and is associated with jet separation from the turbine blade surface. The antivortex film-cooling hole concept has been modeled computationally for a single row of 30 deg angled holes on a flat surface using the 3D Navier–Stokes solver GLENN-HT. A blowing ratio of 1.0 and density ratios of 1.05 and 2.0 are studied. Both film effectiveness and heat transfer coefficient values are computed and compared to standard round hole cases for the same blowing rates. A net heat flux reduction is also determined using both the film effectiveness and heat transfer coefficient values to ascertain the overall effectiveness of the concept. An improvement in film effectiveness of about 0.2 and in net heat flux reduction of about 0.2 is demonstrated for the antivortex concept compared to the standard round hole for both blowing ratios. Detailed flow visualization shows that as expected, the design counteracts the detrimental vorticity of the round hole flow, allowing it to remain attached to the surface.

Sign in / Sign up

Export Citation Format

Share Document