Measurements of the Reactivity of Premixed, Stagnation, Methane-Air Flames at Gas Turbine Relevant Pressures

2018 ◽  
Author(s):  
Philippe Versailles ◽  
Antoine Durocher ◽  
Gilles Bourque ◽  
Jeffrey M. Bergthorson
Keyword(s):  
Gas Turbine ◽  
Laminar Flame ◽  
Turbulent Flame ◽  
Flame Speed ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Chemical Modeling ◽  
Turbulent Flame Speed ◽  
Development And Validation ◽  
Selection Of

The adiabatic, unstrained, laminar flame speed, SL, is a fundamental combustion property, and a premier target for the development and validation of thermochemical mechanisms. It is one of the leading parameters determining the turbulent flame speed, the flame position in burners and combustors, and the occurrence of transient processes, such as flashback and blowout. At pressures relevant to gas turbine engines, SL is generally extracted from the continuous expansion of a spherical reaction front in a combustion bomb. However, independent measurements obtained in different types of apparatuses are required to fully constrain thermochemical mechanisms. Here, a jet-wall, stagnation burner designed for operation at gas turbine relevant conditions is presented, and used to assess the reactivity of premixed, lean-to-rich, methane-air flames at pressures up to 16 atm. One-dimensional (1D) profiles of axial velocity are obtained on the centreline axis of the jet-wall burner using Particle Tracking Velocimetry, and compared to quasi-1D flame simulations performed with a selection of thermochemical mechanisms available in the literature. Significant discrepancies are observed between the numerical and experimental data, and among the predictions of the mechanisms. This motivates further chemical modeling efforts, and implies that designers in industry must carefully select the mechanisms employed for the development of gas turbine combustors.

Measurements of the reactivity of premixed, stagnation, methane-air flames at gas turbine relevant pressures

2018 ◽  
Vol 141 (1) ◽  
Author(s):  
Philippe Versailles ◽  
Antoine Durocher ◽  
Gilles Bourque ◽  
Jeffrey M. Bergthorson
Keyword(s):  
Gas Turbine ◽  
Laminar Flame ◽  
Turbulent Flame ◽  
Flame Speed ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Chemical Modeling ◽  
Transient Phenomena ◽  
Turbulent Flame Speed ◽  
Development And Validation

The adiabatic, unstrained, laminar flame speed, SL, is a fundamental combustion property, and a premier target for the development and validation of thermochemical mechanisms. It is one of the leading parameters determining the turbulent flame speed, the flame position in burners and combustors, and the occurrence of transient phenomena, such as flashback and blowout. At pressures relevant to gas turbine engines, SL is generally extracted from the continuous expansion of a spherical reaction front in a combustion bomb. However, independent measurements obtained in different types of apparatuses are required to fully constrain thermochemical mechanisms. Here, a jet-wall, stagnation burner designed for operation at gas turbine relevant conditions is presented, and used to assess the reactivity of premixed, lean-to-rich, methane–air flames at pressures up to 16 atm. One-dimensional (1D) profiles of axial velocity are obtained on the centerline axis of the burner using particle tracking velocimetry, and compared to quasi-1D flame simulations performed with a selection of thermochemical mechanisms available in the literature. Significant discrepancies are observed between the numerical and experimental data, and among the predictions of the mechanisms. This motivates further chemical modeling efforts, and implies that designers in industry must carefully select the mechanisms employed for the development of gas turbine combustors.

scholarly journals Evaluation of Reduced Kinetics in Simulation of Gasified Biomass Gas Combustion

2013 ◽  
Author(s):  
Xiaoxiang Zhang ◽  
Nur Farizan Munjat ◽  
Jeevan Jayasuriya ◽  
Reza Fakhrai ◽  
Torsten Fransson
Keyword(s):  
Gas Turbine ◽  
Chemical Kinetics ◽  
Cfd Simulation ◽  
Laminar Flame ◽  
Turbulent Flame ◽  
Flame Speed ◽  
Turbulent Flame Speed ◽  
Operation Conditions ◽  
Simulation Results ◽  
Gas Turbine Combustion

It is essentially important to use appropriate chemical kinetic models in the simulation process of gas turbine combustion. To integrate the detailed kinetics into complex combustion simulations has proven to be a computationally expensive task with tens to thousands of elementary reaction steps. It has been suggested that an appropriate simplified kinetics which are computationally efficient could be used instead. Therefore reduced kinetics are often used in CFD simulation of gas turbine combustion. At the same time, simplified kinetics for specific fuels and operation conditions need to be carefully selected to fulfill the accuracy requirements. The applicability of several simplified kinetics for premixed Gasified Biomass Gas (GBG) and air combustion are evaluated in this paper. The current work is motivated by the growing demand of gasified biomass gas (GBG) fueled combustion. Even though simplified kinetic schemes developed for hydrocarbon combustions are published by various researchers, there is little research has been found in literature to evaluate the ability of the simplified chemical kinetics for the GBG combustion. The numerical Simulation tool “CANTERA” is used in the current study for the comparison of both detailed and simplified chemical kinetics. A simulated gas mixture of CO/H2/CH4/CO2/N2 is used for the current evaluation, since the fluctuation of GBG components may have an unpredictable influence on the simulation results. The laminar flame speed has an important influence with flame stability, extinction limits and turbulent flame speed, here it is chosen as an indicator for validation. The simulation results are compared with the experimental data from the previous study [1] which is done by our colleagues. Water vapour which has shown a dilution effect in the experimental study are also put into concern for further validation. As the results indicate, the reduced kinetics which are developed for hydrocarbon or hydrogen combustion need to be highly optimized before using them for GBG combustion. Further optimization of the reduced kinetics is done for GBG and moderate results are achieved using the optimized kinetics compared with the detailed combustion kinetics.

Validation of a New Turbulent Flame Speed Facility for the Study of Gas Turbine Fuel Blends at Elevated Pressure

2019 ◽  
Author(s):  
Anibal Morones ◽  
Mattias A. Turner ◽  
Victor León ◽  
Kyle Ruehle ◽  
Eric L. Petersen
Keyword(s):  
Gas Turbine ◽  
High Speed ◽  
Turbulent Flame ◽  
Elevated Pressure ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Turbulent Flame Speed ◽  
Fuel Blends ◽  
New Apparatus ◽  
Fundamental Insight

Abstract Turbulent combustion is a very active and challenging research topic of direct interest to the design and operation of gas turbine engines. A spherically expanding flame immersed in a turbulent field is one way to gain fundamental insight on the effect of turbulence on combustion. This kind of experiment is often conducted inside a fan-stirred flame bomb, preferably at conditions of high pressure, high temperature, and intense turbulence. A new fan-stirred flame bomb was designed and built to provide a device for conducting fundamental turbulent flame measurements at conditions of interest to gas turbine engines. A literature review on existing systems was used as guidance in the design of the turbulence-generation elements in the present rig. A few options of impellers were explored. The flow field produced by the chosen impeller was measured with Laser Doppler Velocimetry (LDV). A detailed exposition of the vessel engineering and construction are presented, including current activities that will extend the use of the facility for heated experiments up to at least 400 K. Before turbulent experiments were attempted, a validation of the rig accuracy and pressure worthiness was made. Finally, a demonstration of the new apparatus was made by testing a lean mixture of syngas. The experiment matrix using hydrogen and H2/CO mixtures included three levels of pressure (1, 5, and, 10 bar) and three levels of turbulence fluctuation rms (1.4, 2.8, and 5.5 m/s). Data based on the high-speed schlieren diagnostic are presented.

Performance Seeking Control of Regenerative Gas Turbine Engines

2000 ◽  
Author(s):  
Nanahisa Sugiyama
Keyword(s):  
Gas Turbine ◽  
Turbine Engines ◽  
Inlet Temperature ◽  
Gas Turbine Engines ◽  
Efficiency Enhancement ◽  
Turbine Inlet Temperature ◽  
Control Variables ◽  
Turbine Engine ◽  
Selection Of ◽  
Engine Life

A Performance Seeking Control (PSC) can realize the operations advantageous enough to accomplish the economy, safety, engine life, and environmental issues by reducing the control margin to the extremity together with selection of the control variables so that various kinds of parameters will be minimized or maximized. This paper describes the results obtained from the simulation study concerning the PSC aiming at the efficiency enhancement, power improvement, and longer engine life of a two-spool regenerative gas turbine engine having two control variables. By constructing the dynamic simulation of the engine, steady-state characteristics and dynamic characteristics are derived; then, a PSC system is designed and evaluated. It is concluded that the PSC for the gas turbine of this type can be realized by the turbine inlet temperature control.

Marine Operation of Gas Turbine Engines and Waterjet Pumps for Small Passenger Vessels

1979 ◽  
Author(s):  
S. M. Kowleski ◽  
C. D. Harrington
Keyword(s):  
Gas Turbine ◽  
San Francisco ◽  
High Speed ◽  
San Francisco Bay ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Golden Gate ◽  
Operational Problem ◽  
Golden Gate Bridge ◽  
Selection Of

This paper describes the planning, developmental, equipment selection and operational problem phases of the high-speed ferry system presently being operated on San Francisco Bay by the Golden Gate Bridge, Highway and Transportation District. The reasons for the selection of the vessel propulsion package consisting of gas turbine engines and waterjet pumps are discussed in some detail. Most importantly, the paper covers the problems experienced to date with this equipment in continuous marine operation.

Updating the ANSI Standard on Measurement of Exhaust Emissions

1994 ◽  
Author(s):  
J. M. Vaught
Keyword(s):  
Gas Turbine ◽  
Exhaust Emissions ◽  
Measurement Methods ◽  
National Standards ◽  
Turbine Engines ◽  
Measurement Technology ◽  
Gas Turbine Engines ◽  
Regulatory Requirements ◽  
Industrial Gas Turbine ◽  
Selection Of

The American National Standards Institute (ANSI) required that the source testing Standard on Measurement of Exhaust Emissions from Stationary Gas Turbine Engines, B133.9, be brought up to date with today’s regulatory requirements and best measurement technology. The criteria for the design of the Standard along with its content and format are discussed. The selection of measurement methods for gaseous components, smoke, and particulates emitted by present day emission controlled industrial gas turbine engines is presented.

Investigation of Flamelet Generated Manifold Reaction Source Term Closure Models Applied to an Industrial Gas Turbine

2019 ◽  
Author(s):  
George Mallouppas ◽  
Graham Goldin ◽  
Yongzhe Zhang ◽  
Piyush Thakre ◽  
Jim Rogerson
Keyword(s):  
Gas Turbine ◽  
Source Term ◽  
Mixture Fraction ◽  
Turbulent Flame ◽  
Flame Speed ◽  
Turbulent Flame Speed ◽  
Progress Variable ◽  
Flamelet Generated Manifold ◽  
Reactor Types ◽  
Industrial Gas Turbine

Abstract Three Flamelet Generated Manifold reaction source term closure options and two different reactor types are examined with Large Eddy Simulation of an industrial gas turbine combustor operating at 3 bar. This work presents the results for the SGT-100 Dry Low Emission (DLE) gas turbine provided by Siemens Industrial Turbomachinery Ltd. The related experimental study was performed at the German Aerospace Centre, DLR, Stuttgart, Germany. The FGM model approximates the thermo-chemistry in a turbulent flame as that in a simple 0D constant pressure ignition reactors and 1D strained opposed-flow premixed reactors, parametrized by mixture fraction, progress variable, enthalpy and pressure. The first objective of this work is to compare the flame shape and position predicted by these two FGM reactor types. The Kinetic Rate (KR) model, studied in this work, uses the chemical rate from the FGM with assumed shapes, which are a Beta function for mixture fraction and delta functions for reaction progress variable and enthalpy. Another model investigated is the Turbulent Flame-Speed Closure (TFC) model with Zimont turbulent flame speed, which propagates premixed flame fronts at specified turbulent flame speeds. The Thickened Flame Model (TFM), which artificially thickens the flame to sufficiently resolve the internal flame structure on the computational grid, is also explored. Therefore, a second objective of this paper is to compare KR, TFC and TFM with the available experimental data.

Danish Navy Experience With the KV-72 LM2500 CODOG Propulsion Plant

1983 ◽  
Author(s):  
Bent Hansen ◽  
Sloth Larsen ◽  
John W. Tenhundfeld
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Turbine Engines ◽  
Operational Experience ◽  
Gas Turbine Engines ◽  
Joint Effort ◽  
General Electric Company ◽  
Electric Company ◽  
Start Up ◽  
Selection Of

For more than twenty years the Royal Danish Navy (RDN) has been using gas turbine engines for propulsion of fast patrol vessels as well as frigates. This paper, which is the result of a joint effort by the Royal Danish Navy, Aalborg Vaerft Shipyard, and General Electric Company USA, describes how the propulsion system design was developed using previous RDN gas turbine system experience. A detailed description of the ship, the selection of machinery, and design of the propulsion configuration, including the LM2500 gas turbine module, is included. The three Royal Danish “KV-72” corvettes of the NIELS JUEL class have now been in operation for almost three years. Since the start-up of the NIELS JUEL machinery in November 1978 the CODOG propulsion plants aboard this class have accumulated more than 8,000 running hours, of which over 1,500 hours have been in the gas turbine or “sprint” drive mode. Operational experience with the GE LM2500 gas turbines is also described.

Evaporative Cooling of Gas Turbine Engines

2013 ◽  
Vol 135 (8) ◽  
Author(s):  
Mustapha Chaker ◽  
Cyrus B. Meher-Homji
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Low Cost ◽  
Evaporative Cooling ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
End User ◽  
Very High ◽  
Improve Reliability ◽  
Selection Of

There are numerous gas turbine applications in power generation and mechanical drive service where power drop during the periods of high ambient temperature has a very detrimental effect on the production of power or process throughput. Several geographical locations experience very high temperatures with low coincident relative humidities. In such cases media evaporative cooling can be effectively applied as a low cost power augmentation technique. Several misconceptions exist regarding their applicability to evaporative cooling, the most prevalent being that they can only be applied in extremely dry regions. This paper provides a detailed treatment of media evaporative cooling, discussing aspects that would be of value to an end user, including selection of climatic design points, constructional features of evaporative coolers, thermodynamic aspects of its effect on gas turbines, and approaches to improve reliability. It is hoped that this paper will be of value to plant designers, engineering companies, and operating companies that are considering the use of media evaporative cooling.

scholarly journals SELECTION OF TOOL HARD ALLOY FOR PROCESSING PARTS OF GAS TURBINE ENGINES

2018 ◽  
pp. 89-93
Author(s):  
E. V. Artamonov ◽  
A. M. Tveryakov ◽  
A. S. Shtin
Keyword(s):  
Hard Alloy ◽  
Gas Turbine ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Heat Resistant ◽  
Materials Used ◽  
Selection Of

The article reports a brief overview of the choice of tool hard alloy for processing heat-resistant materials used for the manufacturing of parts of gas turbine engines DR-59, J-59, and DG-90.

Sign in / Sign up

Export Citation Format

Share Document