Enhancing Gas Turbine Operation With Heavy Fuel Oil

2013 ◽  
Author(s):  
Vikram Muralidharan ◽  
Matthieu Vierling
Keyword(s):  
Power Generation ◽  
Natural Gas ◽  
Gas Turbine ◽  
Power Plants ◽  
High Efficiency ◽  
Combined Cycle ◽  
Fuel Oil ◽  
Residual Oil ◽  
Heavy Fuel Oil ◽  
Hydro Power

Power generation in south Asia has witnessed a steep fall due to the shortage of natural gas supplies for power plants and poor water storage in reservoirs for low hydro power generation. Due to the current economic scenario, there is worldwide pressure to secure and make more gas and oil available to support global power needs. With constrained fuel sources and increasing environmental focus, the quest for higher efficiency would be imminent. Natural gas combined cycle plants operate at a very high efficiency, increasing the demand for gas. At the same time, countries may continue to look for alternate fuels such as coal and liquid fuels, including crude and residual oil, to increase energy stability and security. In over the past few decades, the technology for refining crude oil has gone through a significant transformation. With the advanced refining process, there are additional lighter distillates produced from crude that could significantly change the quality of residual oil used for producing heavy fuel. Using poor quality residual fuel in a gas turbine to generate power could have many challenges with regards to availability and efficiency of a gas turbine. The fuel needs to be treated prior to combustion and needs a frequent turbine cleaning to recover the lost performance due to fouling. This paper will discuss GE’s recently developed gas turbine features, including automatic water wash, smart cooldown and model based control (MBC) firing temperature control. These features could significantly increase availability and improve the average performance of heavy fuel oil (HFO). The duration of the gas turbine offline water wash sequence and the rate of output degradation due to fouling can be considerably reduced.

Repowering: An Option for Refurbishment of Old Thermal Power Plants in Latin-American Countries

2010 ◽  
Author(s):  
Washington Orlando Irrazabal Bohorquez ◽  
Joa˜o Roberto Barbosa ◽  
Luiz Augusto Horta Nogueira ◽  
Electo E. Silva Lora
Keyword(s):  
Power Plant ◽  
Natural Gas ◽  
Steam Turbine ◽  
Gas Turbine ◽  
Power Plants ◽  
Thermal Power ◽  
Rankine Cycle ◽  
Combined Cycle ◽  
Fuel Oil ◽  
Thermal Power Plants

The operational rules for the electricity markets in Latin America are changing at the same time that the electricity power plants are being subjected to stronger environmental restrictions, fierce competition and free market rules. This is forcing the conventional power plants owners to evaluate the operation of their power plants. Those thermal power plants were built between the 1960’s and the 1990’s. They are old and inefficient, therefore generating expensive electricity and polluting the environment. This study presents the repowering of thermal power plants based on the analysis of three basic concepts: the thermal configuration of the different technological solutions, the costs of the generated electricity and the environmental impact produced by the decrease of the pollutants generated during the electricity production. The case study for the present paper is an Ecuadorian 73 MWe power output steam power plant erected at the end of the 1970’s and has been operating continuously for over 30 years. Six repowering options are studied, focusing the increase of the installed capacity and thermal efficiency on the baseline case. Numerical simulations the seven thermal power plants are evaluated as follows: A. Modified Rankine cycle (73 MWe) with superheating and regeneration, one conventional boiler burning fuel oil and one old steam turbine. B. Fully-fired combined cycle (240 MWe) with two gas turbines burning natural gas, one recuperative boiler and one old steam turbine. C. Fully-fired combined cycle (235 MWe) with one gas turbine burning natural gas, one recuperative boiler and one old steam turbine. D. Fully-fired combined cycle (242 MWe) with one gas turbine burning natural gas, one recuperative boiler and one old steam turbine. The gas turbine has water injection in the combustion chamber. E. Fully-fired combined cycle (242 MWe) with one gas turbine burning natural gas, one recuperative boiler with supplementary burners and one old steam turbine. The gas turbine has steam injection in the combustion chamber. F. Hybrid combined cycle (235 MWe) with one gas turbine burning natural gas, one recuperative boiler with supplementary burners, one old steam boiler burning natural gas and one old steam turbine. G. Hybrid combined cycle (235 MWe) with one gas turbine burning diesel fuel, one recuperative boiler with supplementary burners, one old steam boiler burning fuel oil and one old steam turbine. All the repowering models show higher efficiency when compared with the Rankine cycle [2, 5]. The thermal cycle efficiency is improved from 28% to 50%. The generated electricity costs are reduced to about 50% when the old power plant is converted to a combined cycle one. When a Rankine cycle power plant burning fuel oil is modified to combined cycle burning natural gas, the CO2 specific emissions by kWh are reduced by about 40%. It is concluded that upgrading older thermal power plants is often a cost-effective method for increasing the power output, improving efficiency and reducing emissions [2, 7].

Evaluation of Arabian Super Light and Arabian Extra Light Crude Oil for Use in Dry Low NOx (DLN) Combustion Systems

2019 ◽  
Author(s):  
Jeffrey Goldmeer ◽  
Paul Glaser ◽  
Bassam Mohammad
Keyword(s):  
Power Generation ◽  
Saudi Arabia ◽  
Natural Gas ◽  
Crude Oil ◽  
Gas Turbine ◽  
Power Plants ◽  
Combined Cycle ◽  
Kingdom Of Saudi Arabia ◽  
The Past ◽  
Commercial Operation

Abstract The Kingdom of Saudi Arabia has seen significant transformation in power generation in the past 10 years. There has been an increase in the number of F-class combined cycle power plants being developed and brought into commercial operation. There has also been a shift to the use of natural gas as primary fuel. At the same time, there has been an interest in switching the back-up fuel for new power plants from refined distillates to domestic crude oils. Both Arabian Super Light (ASL) and Arabian Extra Light (AXL) have been proposed for use in new F-class gas turbine combined cycle power plants. This paper provides details on the combustion evaluations of ASL and AXL, as well as the first field usage of ASL in a gas turbine.

Past, Present and Future of Combined Cycle Power Plants: From an A/E’s Perspective

2001 ◽  
Author(s):  
Anup Singh
Keyword(s):  
Power Generation ◽  
Natural Gas ◽  
Gas Turbine ◽  
Rapid Growth ◽  
Gas Turbines ◽  
Power Plants ◽  
Combined Cycle ◽  
Electrical Transmission ◽  
Capital Costs ◽  
The U.S

In the 1970s, power generation from gas turbines was minimal. Gas turbines in those days were run on fuel oil, since there was a so-called “natural gas shortage”. The U.S. Fuel Use Act of 1978 essentially disallowed the use of natural gas for power generation. Hence there was no incentive on the part of gas turbine manufacturers to invest in the development of gas turbine technology. There were many regulatory developments in the 1980s and 1990s, which led to the rapid growth in power generation from gas turbines. These developments included Public Utility Regulatory Policy Act of 1978 (encouraging cogeneration), FERC Order 636 (deregulating natural gas industry), Energy Policy Act of 1992 (creating EWGs and IPPs) and FERC Order 888 (open access to electrical transmission system). There was also a backlash from excessive electric rates due to high capital recovery of nuclear and coal-fired plant costs caused by tremendous cost increase resulting from tightening NRC requirements for nuclear plants and significant SO2/NOx/other emissions controls required for coal-fired plants. During this period, rapid technology developments took place in the metallurgy, design, efficiency, and reliability of gas turbines. In addition, U.S. DOE contributed to these developments by encouraging research and development efforts in high temperature and high efficiency gas turbines. Today we are seeing a tremendous explosion of power generating facilities by electric utilities and Independent Power Producers (IPPs). A few years ago, Merchant Power (generation without power purchase agreements) was unheard of. Today it is growing at a very fast pace. Can this rapid growth be sustained? The paper will explore the factors that will play a significant role in the future growth of gas turbine-based power generation in the U.S. The paper will also discuss the methods and developments that could decrease the capital costs of gas turbine power plants resulting in the lowest cost generation compared to other power generation technologies.

scholarly journals Compressed Natural Gas Technology for Alternative Fuel Power Plants

2018 ◽  
Vol 31 ◽  
pp. 01011
Author(s):  
Isworo Pujotomo
Keyword(s):  
Power Plant ◽  
Natural Gas ◽  
Gas Turbine ◽  
Power Plants ◽  
Combined Cycle ◽  
Fuel Oil ◽  
Steam Power ◽  
Compressed Natural Gas ◽  
Electrical Efficiency ◽  
Steam Power Plant

Gas has great potential to be converted into electrical energy. Indonesia has natural gas reserves up to 50 years in the future, but the optimization of the gas to be converted into electricity is low and unable to compete with coal. Gas is converted into electricity has low electrical efficiency (25%), and the raw materials are more expensive than coal. Steam from a lot of wasted gas turbine, thus the need for utilizing exhaust gas results from gas turbine units. Combined cycle technology (Gas and Steam Power Plant) be a solution to improve the efficiency of electricity. Among other Thermal Units, Steam Power Plant (Combined Cycle Power Plant) has a high electrical efficiency (45%). Weakness of the current Gas and Steam Power Plant peak burden still using fuel oil. Compressed Natural Gas (CNG) Technology may be used to accommodate the gas with little land use. CNG gas stored in the circumstances of great pressure up to 250 bar, in contrast to gas directly converted into electricity in a power plant only 27 bar pressure. Stored in CNG gas used as a fuel to replace load bearing peak. Lawyer System on CNG conversion as well as the power plant is generally only used compressed gas with greater pressure and a bit of land.

scholarly journals Perspective on a Combustion-Free Gas Turbine to Meet Power Generation Needs in the 21st Century

1997 ◽  
Author(s):  
Colin F. McDonald
Keyword(s):  
Power Generation ◽  
Natural Gas ◽  
Gas Turbine ◽  
21St Century ◽  
Gas Turbines ◽  
High Efficiency ◽  
Electrical Power ◽  
Resource Depletion ◽  
Combined Cycle ◽  
Combustion Gas

The combustion gas turbine, operating in both simple and combined cycle modes, is rapidly becoming the preferred prime-mover for electrical power generation for both new plants, and in the repowering of old power stations. In replacing Rankine cycle plants the combustion gas turbine could become dominant in the power generation field early in the next century. Fired currently with natural gas, and later with gasified coal these gas turbines will operate for many decades with no concern about resource depletion. This paper addresses an extension of high efficiency gas turbine technology but uses a combustion and emission-free heat source, namely a high temperature gas cooled nuclear reactor. The motivation for this evolution is essentially twofold, 1) to introduce an environmentally benign plant that does not emit greenhouse gases, and 2) provide electrical power to nations that have no indigenous natural gas or coal supplies. This paper presents a confidence-building approach that eliminates risk towards the goal of making the nuclear gas turbine a reality in the 21st century.

Natural Gas Decarbonization to Reduce CO2 Emission From Combined Cycles—Part II: Steam-Methane Reforming

2000 ◽  
Vol 124 (1) ◽  
pp. 89-95 ◽  
Author(s):  
G. Lozza ◽  
P. Chiesa
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Partial Oxidation ◽  
Power Plants ◽  
Combined Cycle ◽  
Performance Estimation ◽  
Thermodynamic Efficiency ◽  
Methane Reforming ◽  
Operating Pressure ◽  
Carbon Conversion

This paper discusses novel schemes of combined cycle, where natural gas is chemically treated to remove carbon, rather than being directly used as fuel. Carbon conversion to CO2 is achieved before gas turbine combustion. The first part of the paper discussed plant configurations based on natural gas partial oxidation to produce carbon monoxide, converted to carbon dioxide by shift reaction and therefore separated from the fuel gas. The second part will address methane reforming as a starting reaction to achieve the same goal. Plant configuration and performance differs from the previous case because reforming is endothermic and requires high temperature heat and low operating pressure to obtain an elevated carbon conversion. The performance estimation shows that the reformer configuration has a lower efficiency and power output than the systems addressed in Part I. To improve the results, a reheat gas turbine can be used, with different characteristics from commercial machines. The thermodynamic efficiency of the systems of the two papers is compared by an exergetic analysis. The economic performance of natural gas fired power plants including CO2 sequestration is therefore addressed, finding a superiority of the partial oxidation system with chemical absorption. The additional cost of the kWh, due to the ability of CO2 capturing, can be estimated at about 13–14 mill$/kWh.

The Gas Turbine Family GT13E and GT13E2 Provides Reliable Power for Asia

1996 ◽  
Author(s):  
Gregor Gnädig
Keyword(s):  
Power Generation ◽  
Gas Turbines ◽  
Power Plants ◽  
High Efficiency ◽  
Operating Experience ◽  
Diesel Oil ◽  
Combined Cycle ◽  
Asian Countries ◽  
High Efficient ◽  
Prime Movers

Many Asian countries are experiencing economic growth which averages 5–10% per year. This environment has led to a privatization process in the power generation industry from typically state-run utilities to a system in which a federal agency oversees a market divided by private utilities and independent power producers (IPP) with the need for high efficiency, reliable power generation running on natural gas and diesel oil. In the 50 Hz market, modem, high efficient gas turbines of the type GT13E and GT13E2 have been chosen as prime movers in many combined cycle power plants in Asian countries. This paper includes a product description, and a general overview of GT13E and GT13E2 operating experience, well as an economic evaluation of a typical 500 MW combined cycle power plant.

Utilization of Cryogenic Exergy of LNG by MGT (Mirror Gas Turbine)

2000 ◽  
Author(s):  
Y. Tsujikawa ◽  
K. Kaneko ◽  
S. Fujii
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
High Efficiency ◽  
Electric Energy ◽  
Liquefied Natural Gas ◽  
Combined Cycle ◽  
Brayton Cycle ◽  
Exhaust Gas ◽  
Topping Cycle ◽  
Very High

In the course of the worldwide efforts to suppress the global warming, the saving energy becomes more important. Recently, the LNG (liquefied natural gas) terminals in our country have received more than 50 million tons of LNG per year. Therefore, the utilization of the cryogenic exergy in connection with the regasification of LNG gains more and more importance. The aim of this paper is the recovery of the energy consumed in liquefaction using the MGT (Mirror Gas Turbine), which is a kind of new combined cycle of a conventional gas turbine worked as a topping cycle and TG (inverted Brayton cycle) as a bottoming cycle. The optimum characteristics have been calculated and it is shown that this cycle is superior to the current-use gasification systems in employing seawater heats in terms of thermal efficiency and specific output. In the present cycle, the cold of LNG is used to cool the exhaust gas from a turbine of TG, and then the exergy of the liquefied natural gas is transformed to electric energy with a very high efficiency. The main feature of this new concept is the removal of an evaporation system using seawater.

Performance and Cost Analysis of Advanced Gas Turbine Cycles With Precombustion CO2 Capture

2008 ◽  
Vol 131 (2) ◽  
Author(s):  
Stéphanie Hoffmann ◽  
Michael Bartlett ◽  
Matthias Finkenrath ◽  
Andrei Evulet ◽  
Tord Peter Ursin
Keyword(s):  
High Pressure ◽  
Power Plant ◽  
Natural Gas ◽  
Gas Turbine ◽  
Co2 Capture ◽  
Gas Turbines ◽  
High Efficiency ◽  
Combined Cycle ◽  
Co2 Separation ◽  
The Cost

This paper presents the results of an evaluation of advanced combined cycle gas turbine plants with precombustion capture of CO2 from natural gas. In particular, the designs are carried out with the objectives of high efficiency, low capital cost, and low emissions of carbon dioxide to the atmosphere. The novel cycles introduced in this paper are comprised of a high-pressure syngas generation island, in which an air-blown partial oxidation reformer is used to generate syngas from natural gas, and a power island, in which a CO2-lean syngas is burnt in a large frame machine. In order to reduce the efficiency penalty of natural gas reforming, a significant effort is spent evaluating and optimizing alternatives to recover the heat released during the process. CO2 is removed from the shifted syngas using either CO2 absorbing solvents or a CO2 membrane. CO2 separation membranes, in particular, have the potential for considerable cost or energy savings compared with conventional solvent-based separation and benefit from the high-pressure level of the syngas generation island. A feasibility analysis and a cycle performance evaluation are carried out for large frame gas turbines such as the 9FB. Both short-term and long-term solutions have been investigated. An analysis of the cost of CO2 avoided is presented, including an evaluation of the cost of modifying the combined cycle due to CO2 separation. The paper describes a power plant reaching the performance targets of 50% net cycle efficiency and 80% CO2 capture, as well as the cost target of 30$ per ton of CO2 avoided (2006 Q1 basis). This paper indicates a development path to this power plant that minimizes technical risks by incremental implementation of new technology.

Sign in / Sign up

Export Citation Format

Share Document