Impact of Fuel Injection Pressure on Spray and Combustion Characteristics of OME and Diesel Blends

2021 ◽  
Author(s):  
Simon LeBlanc ◽  
Xiao Yu ◽  
Gared Pisciotto ◽  
Xiaoye Han ◽  
Jimi Tjong ◽  
...  
Keyword(s):  
Diesel Fuel ◽  
Fuel Injection ◽  
Direct Injection ◽  
Engine Performance ◽  
Injection Pressure ◽  
Combustion Efficiency ◽  
Particulate Emissions ◽  
Fuel Blend ◽  
Particulate Matter Emissions ◽  
Fuel Injection Pressure

Abstract Emission regulations focus on the simultaneous reduction of NOx and particulate matter emissions, especially for heavy-duty engines. Oxygenated fuels offer significant advantages in reducing particulate emissions while having little effect on NOx emissions. In addition, renewable fuels present a GHG emission advantage to meet the zero-emission requirements of future hydrocarbon fuels. Among the leading contenders, oxymethylene dimethyl ether (OME) fuels have the potential to be used for direct injection applications. OME as a blend with diesel fuel offers a direct means of improving the emissions of current on-road diesel engines without modification. In this paper, an empirical investigation into spray behavior and engine performance of diesel/OME fuel at 10% by mass has been performed under various fuel injection pressures. Neat diesel fuel was tested as a baseline case. The results are compared to tests under matching conditions using a diesel and OME fuel blend with a focus on spray characteristics, combustion behavior, and engine-out emissions. The physical properties of OME improve the volatility of diesel fuel and can tolerate shorter mixing times without promoting PM production. The PM emissions were found to be reduced by up to 50% and the combustion efficiency was improved at matching NOx levels with OME blending.

scholarly journals Influence of Fuel Injection Pressure on the Emissions Characteristics and Engine Performance in a CRDI Diesel Engine Fueled with Palm Biodiesel Blends

Energies ◽  
2019 ◽  
Vol 12 (20) ◽  
pp. 3837 ◽  
Author(s):  
Sam Ki Yoon ◽  
Jun Cong Ge ◽  
Nag Jung Choi
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Fuel Injection ◽  
Injection Pressure ◽  
Biodiesel Fuel ◽  
Nox Emissions ◽  
Oxides Of Nitrogen ◽  
Fuel Blend ◽  
Engine Load ◽  
Fuel Injection Pressure

This experiment investigates the combustion and emissions characteristics of a common rail direct injection (CRDI) diesel engine using various blends of pure diesel fuel and palm biodiesel. Fuel injection pressures of 45 and 65 MPa were investigated under engine loads of 50 and 100 Nm. The fuels studied herein were pure diesel fuel 100 vol.% with 0 vol.% of palm biodiesel (PBD0), pure diesel fuel 80 vol.% blended with 20 vol.% of palm biodiesel (PBD20), and pure diesel fuel 50 vol.% blended with 50 vol.% of palm biodiesel (PBD50). As the fuel injection pressure increased from 45 to 65 MPa under all engine loads, the combustion pressure and heat release rate also increased. The indicated mean effective pressure (IMEP) increased with an increase of the fuel injection pressure. In addition, for 50 Nm of the engine load, an increase to the fuel injection pressure resulted in a reduction of the brake specific fuel consumption (BSFC) by an average of 2.43%. In comparison, for an engine load of 100 Nm, an increase in the fuel injection pressure decreased BSFC by an average of 0.8%. Hydrocarbon (HC) and particulate matter (PM) decreased as fuel pressure increased, independent of the engine load. Increasing fuel injection pressure for 50 Nm engine load using PBD0, PBD20 and PBD50 decreased carbon monoxide (CO) emissions. When the fuel injection pressure was increased from 45 MPa to 65 MPa, oxides of nitrogen (NOx) emissions were increased for both engine loads. For a given fuel injection pressure, NOx emissions increased slightly as the biodiesel content in the fuel blend increased.

Experimental Investigation on Emission Characteristics of Diesel N-Pentanol Blend in Homogeneous Charged Compression Ignition Engine

2021 ◽  
Vol 13 (3) ◽  
Author(s):  
S. Mathavan ◽  
T. Mothilal ◽  
V. Andal ◽  
V. Velukumar
Keyword(s):  
Diesel Fuel ◽  
Internal Combustion Engines ◽  
Fossil Fuels ◽  
Fuel Injection ◽  
Injection Pressure ◽  
Injection Timing ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Fuel Blend ◽  
Fuel Injection Pressure

The invention of internal combustion engines is undoubtedly one of the greatest inventions of the modern era. There has been steady scientific research to look for alternative fuel which is economical, renewable and less harmful to nature and man compared to fossil fuels. The present project is one such experimental work to investigate the performance of a blend of diesel / N-pentanol in an appropriate combustion technique and to establish its suitability as a renewable fuel. The relative performance of diesel fuel and the blend of diesel / n-pentanol will also be analyzed. Diesel fuel blended with 30 percentage n-pentanol is the fuel blend that is proposed to be used in the experiment. Researchers have established that the application of Homogeneously Charged Compression Ignition (HCCI) technique could result in in-cylinder reduction of NOx and PM. Higher thermal efficiency could also be attained. The project also covers studying the emission effect of the diesel/n-pentanol fuel blend for various fuel injection timing, various fuel injection pressure, different EGR rates and different inlet air temperature.

Effect of Fuel Injection Pressure and Engine Speed on Performance, Emissions, Combustion, and Particulate Investigations of Gasohols Fuelled Gasoline Direct Injection Engine

2019 ◽  
Vol 142 (4) ◽  
Author(s):  
Nikhil Sharma ◽  
Avinash Kumar Agarwal
Keyword(s):  
Internal Combustion Engines ◽  
Fuel Injection ◽  
Driving Forces ◽  
Direct Injection ◽  
Engine Performance ◽  
Injection Pressure ◽  
Operating Conditions ◽  
Gasoline Direct Injection ◽  
Primary Alcohols ◽  
Renewable Fuel

Abstract Fuel availability, global warming, and energy security are the three main driving forces, which determine suitability and long-term implementation potential of a renewable fuel for internal combustion engines for a variety of applications. Comprehensive engine experiments were conducted in a single-cylinder gasoline direct injection (GDI) engine prototype having a compression ratio of 10.5, for gaining insights into application of mixtures of gasoline and primary alcohols. Performance, emissions, combustion, and particulate characteristics were determined at different engine speeds (1500, 2000, 2500, 3000 rpm), different fuel injection pressures (FIP: 40, 80, 120, 160 bars) and different test fuel blends namely 15% (v/v) butanol, ethanol, and methanol blended with gasoline, respectively (Bu15, E15, and M15) and baseline gasoline at a fixed (optimum) spark timing of 24 deg before top dead center (bTDC). For a majority of operating conditions, gasohols exhibited superior characteristics except minor engine performance penalty. Gasohols therefore emerged as serious candidate as a transitional renewable fuel for utilization in the existing GDI engines, without requirement of any major hardware changes.

Distribution of Two-Stage Direct Injection CNG-Air Mixture near Lean Limit Using CFD

2013 ◽  
Vol 465-466 ◽  
pp. 448-452
Author(s):  
Mas Fawzi ◽  
Bukhari Manshoor ◽  
Yoshiyuki Kidoguchi ◽  
Yuzuru Nada
Keyword(s):  
Fuel Injection ◽  
Direct Injection ◽  
Engine Performance ◽  
Injection Pressure ◽  
Gas Jet ◽  
Exhaust Emission ◽  
Injection Technique ◽  
Injection Timing ◽  
Two Stage ◽  
Lean Burn

Previous work shows that gas-jet ignition with two-stage injection technique is effective to extend lean combustible ranges of CNG engines. In this report, the robustness of the gas-jet ignition with two-stage injection method was investigated purposely to improve the performance of a lean burn direct injection CNG engine. The experiment was conducted using an engine at speed of 900 rpm, fuel-injection-pressure of 3MPa, equivalence ratio at 0.8, and ignition timing at top dead center. The effect of first injection timing on the test engine performance and exhaust emission was analyzed. First injection timings near the gas-jet ignition produced unstable combustion with occurrence of misfires except at a timing which produced distinctively good combustion with low HC and CO emissions. Computational fluid dynamics was used to provide hindsight of the fuel-air mixture distribution that might be the cause of misfires occurrence at certain injection timings.

Effects of Fuel Injection Pressure on Spray Characteristics and Vaporization Characteristics of Diesel Fuel Spray

2016 ◽  
Vol 2016 (0) ◽  
pp. G0700102
Author(s):  
Shun SHIMOTSUMAGARI ◽  
Takeru IWAMOTO ◽  
Masaoki SUGIHARA ◽  
Hideki HASHIMOTO ◽  
Osamu MORIUE
Keyword(s):  
Diesel Fuel ◽  
Fuel Injection ◽  
Injection Pressure ◽  
Fuel Spray ◽  
Spray Characteristics ◽  
Fuel Injection Pressure

Effects of Different Biodiesel Blends on Heat Release and Its Related Parameters

2006 ◽  
Author(s):  
Girish Parvate-Patil ◽  
Manuel Vasquez ◽  
Malcolm Payne
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Fuel Injection ◽  
Load Condition ◽  
Engine Performance ◽  
Injection Pressure ◽  
Single Cylinder ◽  
Medium Speed ◽  
Performance And Emissions ◽  
Fuel Injection Pressure

This paper emphasizes on the effects of different biodiesels and diesel on; heat release, ignition delay, endothermic and exothermic reactions, NOx, fuel injection pressure due to the fuel’s modulus of elasticity and cylinder pressure. Two 100% biodiesel and its blends of 20% with of low sulfur #2 diesel, and #2 diesel are tested on a single cylinder diesel engine under full load condition. Engine performance and emissions data is obtained for 100% and 20% biodiesels blends and #2 diesel. Testes were conducted at Engine Systems Development Centre, Inc. (ESDC) to evaluate the effects of biodiesel and its blends on the performance and emissions of a single-cylinder medium-speed diesel engine. The main objective of this work was to gain initial information and experience about biodiesel for railway application based on which biodiesel and its blends could be recommended for further investigation on actual locomotives.

Sign in / Sign up

Export Citation Format

Share Document