Distribution of Two-Stage Direct Injection CNG-Air Mixture near Lean Limit Using CFD

2013 ◽  
Vol 465-466 ◽  
pp. 448-452
Author(s):  
Mas Fawzi ◽  
Bukhari Manshoor ◽  
Yoshiyuki Kidoguchi ◽  
Yuzuru Nada
Keyword(s):  
Fuel Injection ◽  
Direct Injection ◽  
Engine Performance ◽  
Injection Pressure ◽  
Gas Jet ◽  
Exhaust Emission ◽  
Injection Technique ◽  
Injection Timing ◽  
Two Stage ◽  
Lean Burn

Previous work shows that gas-jet ignition with two-stage injection technique is effective to extend lean combustible ranges of CNG engines. In this report, the robustness of the gas-jet ignition with two-stage injection method was investigated purposely to improve the performance of a lean burn direct injection CNG engine. The experiment was conducted using an engine at speed of 900 rpm, fuel-injection-pressure of 3MPa, equivalence ratio at 0.8, and ignition timing at top dead center. The effect of first injection timing on the test engine performance and exhaust emission was analyzed. First injection timings near the gas-jet ignition produced unstable combustion with occurrence of misfires except at a timing which produced distinctively good combustion with low HC and CO emissions. Computational fluid dynamics was used to provide hindsight of the fuel-air mixture distribution that might be the cause of misfires occurrence at certain injection timings.

Effect of Two-Stage Injection Timing on a Gas-Jet Ignition CNG Engine

2014 ◽  
Vol 663 ◽  
pp. 342-346
Author(s):  
Mas Fawzi Mohd Ali ◽  
Amir Khalid ◽  
Yoshiyuki Kidoguchi
Keyword(s):  
Fuel Injection ◽  
Engine Performance ◽  
Injection Pressure ◽  
Gas Jet ◽  
Exhaust Emission ◽  
Injection Technique ◽  
Injection Timing ◽  
Two Stage ◽  
Lean Burn ◽  
Cng Engine

Compressed natural gas (CNG) engines normally operate in lean condition to take the advantage of higher efficiency and better fuel economy. Several studies have shown that gas-jet ignition with two-stage injection technique is effective to extend the lean combustible range of CNG engines. This paper investigates the effectiveness of such technique using a prototype lean burn direct injection CNG engine. The experiment was conducted at speed of 900 rpm, fuel injection pressure of 3 MPa, equivalence ratio φ=0.8, and ignition timing at top dead center. The effect of first injection timing on the test engine performance and exhaust emission was analyzed. The result shows that the first injection timing is crucial in determining the performance of the engine. First injection timings when the piston is near to bottom dead center produced relatively stable combustion. First injection timings when the piston is at midpoint produced misfire. First injection timings near the gas-jet ignition produced unstable combustion except at a certain timings which produced acceptable combustion with low hydrocarbon and carbon monoxide emissions.

Correlation of Ignitability with Injection Timing for Direct Injection Combustion Fuelled with Compressed Natural Gas and Gasoline

2003 ◽  
Vol 217 (6) ◽  
pp. 499-506 ◽  
Author(s):  
Z Huang ◽  
S Shiga ◽  
T Ueda ◽  
H Nakamura ◽  
T Ishima ◽  
...  
Keyword(s):  
Natural Gas ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection Pressure ◽  
Gasoline Direct Injection ◽  
Injection Timing ◽  
Electrode Gap ◽  
Lean Burn ◽  
Compressed Natural Gas ◽  
Study Results

A study on the correlation of ignitability with fuel injection timing for direct injection combustion fuelled with natural gas and gasoline was carried out by using a rapid compression machine. The injection pressure of natural gas is 9 MPa and the injection pressure of gasoline is 7 MPa. The study results show that natural gas direct injection possesses higher momentum than that of gasoline, and this is beneficial to the combustion enhancement since a higher intensity of turbulence could be induced. Correlation of ignitability with injection timing shows better behaviour in natural gas direct injection, and this correlation is insensitive to injection modes in the case of natural gas. Thus, natural gas direct injection would have better engine applicability under cold-start conditions. The lean burn limits of natural gas and gasoline direct injection can extend to extremely low equivalence ratio when the ignitable stratified mixture exists around the spark electrode gap by optimizing the injection timing.

Effect of Fuel Injection Pressure and Engine Speed on Performance, Emissions, Combustion, and Particulate Investigations of Gasohols Fuelled Gasoline Direct Injection Engine

2019 ◽  
Vol 142 (4) ◽  
Author(s):  
Nikhil Sharma ◽  
Avinash Kumar Agarwal
Keyword(s):  
Internal Combustion Engines ◽  
Fuel Injection ◽  
Driving Forces ◽  
Direct Injection ◽  
Engine Performance ◽  
Injection Pressure ◽  
Operating Conditions ◽  
Gasoline Direct Injection ◽  
Primary Alcohols ◽  
Renewable Fuel

Abstract Fuel availability, global warming, and energy security are the three main driving forces, which determine suitability and long-term implementation potential of a renewable fuel for internal combustion engines for a variety of applications. Comprehensive engine experiments were conducted in a single-cylinder gasoline direct injection (GDI) engine prototype having a compression ratio of 10.5, for gaining insights into application of mixtures of gasoline and primary alcohols. Performance, emissions, combustion, and particulate characteristics were determined at different engine speeds (1500, 2000, 2500, 3000 rpm), different fuel injection pressures (FIP: 40, 80, 120, 160 bars) and different test fuel blends namely 15% (v/v) butanol, ethanol, and methanol blended with gasoline, respectively (Bu15, E15, and M15) and baseline gasoline at a fixed (optimum) spark timing of 24 deg before top dead center (bTDC). For a majority of operating conditions, gasohols exhibited superior characteristics except minor engine performance penalty. Gasohols therefore emerged as serious candidate as a transitional renewable fuel for utilization in the existing GDI engines, without requirement of any major hardware changes.

Experimental and Numerical Analysis on the Influence of Direct Fuel Injection Into O2-Depleted Environment of a GDI-HCCI Engine

2020 ◽  
Author(s):  
Ratnak Sok ◽  
Jin Kusaka
Keyword(s):  
Fuel Injection ◽  
Direct Injection ◽  
Injection Pressure ◽  
Single Pulse ◽  
Gasoline Direct Injection ◽  
Injection Timing ◽  
Rich Mixture ◽  
Intake Stroke ◽  
Shift Reaction ◽  
Direct Fuel Injection

Abstract Injected gasoline into the O2-depleted environment in the recompression stroke can be converted into light hydrocarbons due to thermal cracking, partial oxidation, and water-gas shift reaction. These reformate species influence the combustion phenomena of gasoline direct injection homogeneous charge compression ignition (GDI-HCCI) engines. In this work, a production-based single-cylinder research engine was boosted to reach IMEPn = 0.55 MPa in which its indicated efficiency peaks at 40–41%. Experimentally, the main combustion phases are advanced under single-pulse direct fuel injection into the negative valve overlap (NVO) compared with that of the intake stroke. NVO peak in-cylinder pressures are lower than that of motoring, which emphasizes that endothermic reaction occurs during the interval. Low O2 concentration could play a role in this evaporative charge cooling effect. This phenomenon limits the oxidation reaction, and the thermal effect is not pronounced. For understanding the recompression reaction phenomena, 0D simulation with three different chemical reaction mechanisms is studied to clarify that influences of direct injection timing in NVO on combustion advancements are kinetically limited by reforming. The 0D results show the same increasing tendencies of classical reformed species of rich-mixture such as C3H6, C2H4, CH4, CO, and H2 as functions of injection timings. By combining these reformed species into the main fuel-air mixture, predicted ignition delays are shortened. The effects of the reformed species on the main combustion are confirmed by 3D-CFD calculation, and the results show that OH radical generation is advanced under NVO fuel injection compared with that of intake stroke conditions thus earlier heat release and cylinder pressure are noticeable. Also, parametric studies on injection pressure and double-pulse injections on engine combustion are performed experimentally.

Experimental and Theoretical Study of Injection Timing on Performance and Exhaust Emissions in a Port-Injected Gasoline Engine

2006 ◽  
Author(s):  
E. Movahednejad ◽  
F. Ommi ◽  
M. Hosseinalipour ◽  
O. Samimi
Keyword(s):  
Gasoline Engine ◽  
Fuel Injection ◽  
Engine Performance ◽  
Fuel Mixture ◽  
Exhaust Emissions ◽  
Operating Conditions ◽  
Exhaust Emission ◽  
Injection Timing ◽  
Intake Port ◽  
One Dimensional

For spark ignition engines, the fuel-air mixture preparation process is known to have a significant influence on engine performance and exhaust emissions. In this paper, an experimental study is made to characterize the spray characteristics of an injector with multi-disc nozzle used in the engine. The distributions of the droplet size and velocity and volume flux were characterized by a PDA system. Also a model of a 4 cylinder multi-point fuel injection engine was prepared using a fluid dynamics code. By this code one-dimensional, unsteady, multiphase flow in the intake port has been modeled to study the mixture formation process in the intake port. Also, one-dimensional air flow and wall fuel film flow and a two-dimensional fuel droplet flow have been modeled, including the effects of in-cylinder mixture back flows into the port. The accuracy of model was verified using experimental results of the engine testing showing good agreement between the model and the real engine. As a result, predictions are obtained that provide a detailed picture of the air-fuel mixture properties along the intake port. A comparison was made on engine performance and exhaust emission in different fuel injection timing for 2600 rpm and different loads. According to the present investigation, optimum injection timing for different engine operating conditions was found.

scholarly journals Theoretical study to determine the proper injection system for upgrading fuel system of diesel engine om357 to common rail system

2018 ◽  
Vol 7 (4) ◽  
pp. 2594
Author(s):  
Razieh Pourdarbani ◽  
Ramin Aminfar
Keyword(s):  
Diesel Engine ◽  
Fuel Injection ◽  
Engine Performance ◽  
Injection Pressure ◽  
Common Rail ◽  
Injection System ◽  
Injection Timing ◽  
Common Rail System ◽  
Common Rail Injection System ◽  
Multi Stage

In this research, we tried to investigate all the fuel injection systems of diesel engines in order to select the most suitable fuel injection system for the OM357 diesel engine to achieve the highest efficiency, maximize output torque and reduce emissions and even reduce fuel consumption. The prevailing strategy for this study was to investigate the effect of injection pressure changes, injection timing and multi-stage injection. By comparing the engines equipped with common rail injection system, the proposed injector for engine OM357 is solenoid, due to the cost of this type of injector, MAP and controller (ECU). It is clear that this will not be possible only with the optimization of the injection system, and so other systems that influence engine performance such as the engine's respiratory system and combustion chamber shape, etc. should also be optimized. 

Characteristics of Lean and Stoichiometric Combustion of Compressed Natural Gas in a Direct Injection Engine

2011 ◽  
Vol 110-116 ◽  
pp. 357-369 ◽  
Author(s):  
Raja Shahzad ◽  
P. Naveenchandran ◽  
A. Rashid ◽  
Amir Aziz
Keyword(s):  
Fuel Injection ◽  
Direct Injection ◽  
Engine Performance ◽  
Initial Mixture ◽  
Combustion Characteristics ◽  
Injection Timing ◽  
Direct Injection Engine ◽  
Fuel Injection Timing ◽  
Initial Stage ◽  
Air Mixing

This paper discusses the combustion characteristics of CNG under lean and stochiometric conditions in a direct injection engine. The experiments were carried out on a dedicated CNG-Direct Injection engine with 14:1 compression ratio. Combustion characteristics of CNG have been investigated on various injection timings. Injection timing of the fuel injection timing had significant effects on the engine performance, combustion and emissions. The effects became more significant when injection timing was retarded. Injection timing was set after the closing of intake valve and experiments are conducted at 0% and 50% load conditions. Lean stratified operation experiences faster combustion compared to that of stochiometric. In lean stratified operation, there were fast burn rates at the initial stage and slower burning at the later stage. Whereas in stochiometric conditions there is a slightly slower burn at the initial stage and a moderately faster burn at the later stage. The faster initial combustion in lean stratified operation might be due to rapid burn of the initial mixture due to higher turbulence, while a slower burn in the later stage due to diffusion. In contrary to that in stochiometric operations the initial burn is slightly slower, due to moderately strong turbulence and a faster burn due to moderately proceeding mixture. Thus the main effect of fuel injection timing can be explained by the fuel air mixing and the turbulence produced.

Sign in / Sign up

Export Citation Format

Share Document