Simulation of Axial Flow in a Bare Rod Bundle Using a Non-Linear Turbulence Model With High and Low Reynolds Approximations

2002 ◽  
Author(s):  
Marcelo J. S. de Lemos ◽  
Marcelo Assato
Keyword(s):  
Control Volume ◽  
Numerical Technique ◽  
Axial Flow ◽  
Simple Algorithm ◽  
Eddy Viscosity Model ◽  
Rod Bundle ◽  
Non Linear ◽  
Fully Developed Turbulent Flow ◽  
Low Reynolds ◽  
Volume Method

This work presents a numerical investigation of fully developed turbulent flow in a triangular sub-channel of a bare rod bundle using a Non-Linear Eddy Viscosity Model (NLEVM). The numerical technique employed for discretizing the governing equations is the control-volume method with a boundary-fitted non-orthogonal coordinate system. The SIMPLE algorithm was used to correct the pressure field. The classical wall function and a low Reynolds model were used in order to handle flow calculations near the wall. In this work, the influence of constants of calibration existing in the non-linear terms of the model is analyzed.

Turbulent Flow and Heat Transfer in a Porous Chamber

2003 ◽  
Author(s):  
Marcelo Assato ◽  
Marcelo J. S. de Lemos
Keyword(s):  
Turbulent Flow ◽  
Control Volume ◽  
Numerical Technique ◽  
Turbulence Models ◽  
Simple Algorithm ◽  
Macroscopic Models ◽  
Flow And Heat Transfer ◽  
Non Linear ◽  
Porosity And Permeability ◽  
Volume Method

This work presents a numerical investigation of turbulent flow past a porous structure in a channel using linear and non-linear eddy viscosity macroscopic models. Parameters such as porosity and permeability of the porous material are varied in order to analyze their effects on the flow pattern, particularly on the damping of the recirculating bubble after the entrance and exit regions. The numerical technique employed for discretizing the governing equations is the control-volume method. The SIMPLE algorithm is used to correct the pressure field. The classical wall function is utilized in order to handle flow calculation near the wall. A discussion on the use of this technique for simulating the flow in question is presented. Comparisons of results simulated with both linear and non-linear turbulence models are shown.

Numerical Simulation of Laminar Confined Impinging Jet in a Composite Channel

2008 ◽  
Author(s):  
Marcelo J. S. de Lemos
Keyword(s):  
Porous Layer ◽  
Control Volume ◽  
Numerical Technique ◽  
Simple Algorithm ◽  
Local Distribution ◽  
Governing Equations ◽  
Stagnation Region ◽  
Volume Method ◽  
Material Porosity ◽  
Macroscopic Equations

This work shows numerical results for a jet impinging onto a flat plane covered with a layer of a porous material. Porosity of the porous layer is varied in order to analyze its effect on the local distribution of Nu. Macroscopic equations for mass and momentum ae obtained based on the volume-average concept. The numerical technique employed for discretizing the governing equations was the control volume method with a boundary-fitted non-orthogonal coordinate system. The SIMPLE algorithm was used to handle the pressure-velocity coupling. Results indicate that inclusion of a porous layer decreases the peak in Nu avoiding excessive heating or cooling near the stagnation region.

scholarly journals Stirred tank simulation using Partially-Averaged Navier-Stokes $$k_u-\epsilon _u$$ turbulence model

2021 ◽  
Vol 3 (5) ◽  
Author(s):  
Srimanta Maji ◽  
Akshaya K. Sahu
Keyword(s):  
Experimental Data ◽  
Turbulence Model ◽  
Power Law ◽  
Control Volume ◽  
Axial Flow ◽  
Simple Algorithm ◽  
Stirred Tank ◽  
Navier Stokes ◽  
Flow Variables ◽  
Volume Method

AbstractIn the present study, simulation of a stirred tank using axial flow impeller has been studied numerically to see the behaviour of flow variables in the entire vessel. It is assumed that the flow is steady state, two dimensional, incompressible and axisymmetric. For simulation, Partially-Averaged Navier-Stokes (PANS) $$k_u-\epsilon _u$$ k u - ϵ u turbulence model has been taken into account. For discretization, control volume method along with upwind and power-law schemes have been taken. The solutions are obtained by using the SIMPLE algorithm. The boundary conditions for impeller are given by using the experimental data. The main objective is to investigate the influence of different filters width $$f_k$$ f k of the PANS $$k_u-\epsilon _u$$ k u - ϵ u model parameter on the characteristic flow variables. The predicted results of the PANS $$k_u-\epsilon _u$$ k u - ϵ u model for different $$f_k$$ f k have been compared with the experimental data at different axial levels of the stirred tank. It has been observed that the power-law scheme gives better agreement with the experimental data. Further, near the impeller region, PANS predicted results are better for smaller $$f_k$$ f k . Also, Reynolds-Averaged Navier-Stokes Shear Stress Transport (SST) $$k-\omega $$ k - ω turbulence model has been tested for comparative study.

Turbulent Impinging Jet Into a Rigid Porous Layer

2011 ◽  
Author(s):  
Marcelo J. S. de Lemos
Keyword(s):  
Porous Layer ◽  
Control Volume ◽  
Numerical Technique ◽  
Simple Algorithm ◽  
Stagnation Region ◽  
Thermally Conducting ◽  
Energy Equations ◽  
Volume Method ◽  
Highly Porous ◽  
Macroscopic Equations

This work shows simulations for a turbulent jet impinging against a flat plane covered with a layer of permeable and thermally conducting material. Distinct energy equations are considered for the porous layer attached to the wall and for the fluid that impinges on it. Parameters such as Reynolds number, porosity, permeability, thickness and thermal conductivity of the porous layer are varied in order to analyze their effects on the local distribution of Nu. The macroscopic equations for mass, momentum and energy are obtained based on volume-average concept. The numerical technique employed for discretizing the governing equations was the control volume method with a boundary-fitted non-orthogonal coordinate system. The SIMPLE algorithm was used to handle the pressure-velocity coupling. Results indicate that inclusion of a porous layer eliminates the peak in Nu at the stagnation region. For highly porous and highly permeable material, simulations indicate that the integral heat flux from the wall is enhanced when a thermally conducting porous material is attached to the wall.

A New Implicit Numerical Treatment for Non-Linear Turbulence Models and Its Application to Channels With Spatially Periodic Corrugated Walls

2002 ◽  
Author(s):  
Marcelo Assato ◽  
Marcelo J. S. de Lemos
Keyword(s):  
Control Volume ◽  
Turbulence Models ◽  
Simple Algorithm ◽  
Numerical Treatment ◽  
Linear Diffusion ◽  
Viscosity Models ◽  
Non Linear ◽  
Diverging Channel ◽  
Spatially Periodic ◽  
Volume Method

This work examines the performance of linear and nonlinear eddy-viscosity models when used to predict the turbulent flow in periodically sinusoidal-wave channels. Two geometries are investigated, namely a converging-diverging channel and a channel with concave-convex walls. The numerical method employed for the discretization of the equations is the control-volume method in a boundary-fitted non-orthogonal coordinate system. The SIMPLE algorithm is used for correcting the pressure field. The classical wall function and a low Reynolds model are used to describe the flow near the wall. Comparisons between those two approaches using linear and non-linear turbulence models are done. Here, an implicit numerical treatment was proposed for the non-linear diffusion terms of the momentum equations in order to increase the robustness of the solution method.

Laminar Heat Transfer on a Wall Covered With a Layer of Porous Material Simulated With a Two-Energy Equation Model

2010 ◽  
Author(s):  
Marcelo J. S. de Lemos ◽  
Felipe T. Do´rea
Keyword(s):  
Porous Material ◽  
Control Volume ◽  
Numerical Technique ◽  
Simple Algorithm ◽  
Porous Matrix ◽  
Equation Model ◽  
Energy Model ◽  
Governing Equations ◽  
Volume Method ◽  
Macroscopic Equations

This paper presents simulations for a jet impinging against a flat plane covered with a layer of a porous material. Macroscopic equations for mass, momentum and energy, for the fluid and for the porous matrix, are obtained based on the volume-average concept. The numerical technique employed for discretizing the governing equations was the control volume method with a boundary-fitted non-orthogonal coordinate system. The SIMPLE algorithm was used to handle the pressure-velocity coupling. The effect of porosity and energy model on the local distribution of Nu was analyzed. Results indicate that for low porosity materials, a substantially different Nu number is calculated depending on the energy model applied.

A Thermo-Mechanical Model for a Counterflow Biomass Gasifier

2014 ◽  
Vol 354 ◽  
pp. 227-235
Author(s):  
Marcelo J.S. de Lemos
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Control Volume ◽  
Simple Algorithm ◽  
Thermal Capacity ◽  
Macroscopic Model ◽  
Algebraic Equations ◽  
Medium Permeability ◽  
Mechanical Approach ◽  
Volume Method

This article presents a thermo-mechanical approach to investigate heat transfer between solid and fluid phases in a model gasifier. A two-temperature equation approach is applied in addition to a macroscopic model for laminar flow through a porous moving bed. Transport equations are discretized using the control-volume method and the system of algebraic equations is relaxed via the SIMPLE algorithm. The effects on inter-phase heat transfer due to variation of medium permeability, thermal conductivity and thermal capacity are analyzed. Results indicate that for smaller medium permeabilities, as well as for higher solid-to-fluid thermal capacity and thermal conductivity ratios, enhancement of heat transfer between phases is observed.

Turbulent Impinging Jets Into Permeable Media

2006 ◽  
Author(s):  
Marcelo J. S. de Lemos ◽  
Daniel R. Graminho
Keyword(s):  
Control Volume ◽  
Numerical Technique ◽  
Flow Distribution ◽  
Simple Algorithm ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Impinging Jets ◽  
Porous Substrate ◽  
Transfer Coefficients ◽  
Permeable Media

Impinging jets are widely used in industry to modify local heat transfer coefficients. The addition of a porous substrate covering the surface contributes to better flow distribution, which favors many engineering applications. Motivated by that, this work shows numerical results for a turbulent jet impinging against a cylindrical enclosure with a porous substrate at the bottom. Macroscopic time-averaged equations for mass and momentum are obtained based on a concept called double decomposition, which considers spatial deviations and temporal fluctuations of flow properties. The numerical technique employed for discretizing the governing equations is the control volume method in conjunction with a boundary-fitted coordinate system. The SIMPLE algorithm is used to handle the pressure-velocity coupling. The influence of the cylinder height on the mean and statistical flow fields within the entire cavity is presented.

Free convective of a linear heterogeneous liquid in a square cavity at side heating

2020 ◽  
pp. 108-116
Author(s):  
K.V. Moiseev ◽  
◽  
V.S. Kuleshov ◽  
R.N. Bakhtizin ◽  
◽  
...  
Keyword(s):  
Control Volume ◽  
Three Dimensional ◽  
Simple Algorithm ◽  
Double Diffusion ◽  
Boussinesq Approximation ◽  
Square Cavity ◽  
Cell Height ◽  
Volume Method ◽  
Dimensional Statement ◽  
Stratified Liquid

In this work the problem of free convection of the Newtonian poorly stratified liquid in the cell warmed up from left and cooled from right with the heat-insulated horizontal boarders is presented. Liquid with small concentration of salt and initial linear stratification on cell height is considered. The model of double diffusion in a Boussinesq approximation is applied to model the process. The problem is solved both in two - and three-dimensional statement by means of a control volume method and a SIMPLE algorithm. It is shown that vortex structures at the layered mode of convection have quasi-two-dimensional character.

Simulation of Combustion in Porous Media With a Two-Energy Equation Model

2011 ◽  
Author(s):  
Marcelo J. S. deLemos ◽  
Jose´ E. A. Coutinho
Keyword(s):  
Porous Media ◽  
Flame Front ◽  
Control Volume ◽  
Numerical Technique ◽  
Simple Algorithm ◽  
Equation Model ◽  
Gas Temperature ◽  
Inlet Velocity ◽  
Excess Air ◽  
Porous Burner

This work presents numerical results for two-dimensional combustion of an air/methane mixture in inert porous media using turbulence and radiation models. Distinct energy equations are considered for the porous burner and for the fuel in it. Inlet velocity and excess air-to-fuel ratio are varied in order to analyze their effects on temperature and flame front location. The macroscopic equations for mass, momentum and energy are obtained based on the volume average concept. The numerical technique employed for discretizing the governing equations was the control volume method with a boundary-fitted non-orthogonal coordinate system. The SIMPLE algorithm was used to handle the pressure-velocity coupling. Results indicate that for high excess air values, the gas temperature peaks are reduced. Also, for the same conditions the flame front moves towards the exit of the burner. Results also indicate that the same flame front behavior occurs as the inlet velocity increases.

Sign in / Sign up

Export Citation Format

Share Document