Identifying Coulomb and Viscous Friction in Forced Oscillators by Using a Harmonic Energy Balance

2002 ◽  
Author(s):  
Jin-Wei Liang ◽  
Brian F. Feeny
Keyword(s):  
Dry Friction ◽  
Mechanical Vibration ◽  
Viscous Friction ◽  
Viscous Damping ◽  
Equivalent Viscous Damping ◽  
Experimental Systems ◽  
Estimation Equations ◽  
Forced Oscillators ◽  
Friction Parameters ◽  
Relationship Of

This study makes use of energy dissipation to identify damping from mechanical vibration systems. Both the viscous damping and dry friction are assumed to coexist in vibration systems. By balancing the energy loss as registered in the force-displacement relationship of the real system against that of a theoretical model, consisting of viscous damping and dry friction components, the identification algorithms are developed and the equivalent viscous-damping and dry-friction parameters are estimated. We apply the estimation equations to both numerical and experimental systems to show the effectiveness and reliability of the new identification method.

A New Method for the Identification of Coulomb and Viscous Friction

Tribology ◽  
2005 ◽  
Author(s):  
Lilan Liu ◽  
Hongzhao Liu ◽  
Ziying Wu ◽  
Daning Yuan
Keyword(s):  
Damping Ratio ◽  
Viscous Friction ◽  
Least Square Method ◽  
Least Square ◽  
New Method ◽  
Exponential Fitting ◽  
Viscous Damping ◽  
Equivalent Viscous Damping ◽  
Fitting Method ◽  
Friction Parameters

In this paper, a new method for simultaneously estimating Coulomb and viscous friction parameters from the free vibration of a damped oscillator is put forward. In the method, the nonlinear vibration equation with Coulomb and viscous friction is transformed into a linear procedure with equivalent viscous damping which is a function of velocity. The proposed method works well with both the displacement and velocity response data, while the case of zero velocity is not considered. From the displacement decaying curve, the equivalent viscous damping ratios are obtained by means of the local exponential fitting method, and different velocities corresponding to the equivalent viscous damping ratios are also obtained from the velocity decaying curve. Then, according to the relationship between the equivalent viscous damping ratio and the velocity, the Coulomb friction and the viscous damping are achieved using the least square method. The validity and accuracy of the proposed method are demonstrated through good simulation results.

Structural Stiffness, Dry-Friction Coefficient and Equivalent Viscous Damping in a Bump-Type Foil Gas Bearing

2005 ◽  
Author(s):  
Dario Rubio ◽  
Luis San Andre´s
Keyword(s):  
Friction Coefficient ◽  
Dry Friction ◽  
Structural Parameters ◽  
Excitation Frequency ◽  
Single Frequency ◽  
Viscous Damping ◽  
Periodic Load ◽  
Stick Slip ◽  
Equivalent Viscous Damping ◽  
Frequency Domain Methods

High performance oil-free turbomachinery implements gas foil bearings (FBs) to improve mechanical efficiency in compact units. FB design, however, is still largely empirical due to their mechanical complexity. The paper provides test results for the structural parameters in a bump-type foil bearing. The stiffness and damping (Coulomb or viscous type) coefficients characterize the bearing compliant structure. The test bearing, 38.1 mm in diameter and length, consists of a thin top foil supported on bump-foil strips. A prior investigation identified the stiffness due to static loads. Presently, the test FB is mounted on a non-rotating stiff shaft and a shaker exerts single frequency loads on the bearing. The dynamic tests are conducted at shaft surface temperatures from 25 °C to 75°C. Time and frequency domain methods are implemented to determine the FB parameters from the recorded periodic load and bearing motions. Both methods deliver identical parameters. The dry friction coefficient ranges from 0.05 to 0.20, increasing as the amplitude of load increases. The recorded motions evidence a resonance at the system natural frequency, i.e. null damping. The test derived equivalent viscous damping is inversely proportional to the motion amplitude and excitation frequency. The characteristic stick-slip of dry friction is dominant at small amplitude dynamic loads leading to a hardening effect (stiffening) of the FB structure. The operating temperature produces shaft growth generating a bearing preload. However, the temperature does not affect significantly the identified FB parameters, albeit the experimental range was too small considering the bearings intended use in industry.

Structural Stiffness, Dry Friction Coefficient, and Equivalent Viscous Damping in a Bump-Type Foil Gas Bearing

2006 ◽  
Vol 129 (2) ◽  
pp. 494-502 ◽  
Author(s):  
Dario Rubio ◽  
Luis San Andres
Keyword(s):  
Friction Coefficient ◽  
Dry Friction ◽  
Structural Parameters ◽  
Excitation Frequency ◽  
Single Frequency ◽  
Viscous Damping ◽  
Periodic Load ◽  
Stick Slip ◽  
Equivalent Viscous Damping ◽  
Frequency Domain Methods

High performance oil-free turbomachinery implements gas foil bearings (FBs) to improve mechanical efficiency in compact units. FB design, however, is still largely empirical due to its mechanical complexity. The paper provides test results for the structural parameters in a bump-type foil bearing. The stiffness and damping (Coulomb or viscous type) coefficients characterize the bearing compliant structure. The test bearing, 38.1mm in diameter and length, consists of a thin top foil supported on bump-foil strips. A prior investigation identified the stiffness due to static loads. Presently, the test FB is mounted on a non-rotating stiff shaft and a shaker exerts single frequency loads on the bearing. The dynamic tests are conducted at shaft surface temperatures from 25to75°C. Time and frequency domain methods are implemented to determine the FB parameters from the recorded periodic load and bearing motions. Both methods deliver identical parameters. The dry friction coefficient ranges from 0.05 to 0.20, increasing as the amplitude of load increases. The recorded motions evidence a resonance at the system natural frequency, i.e., null damping. The test derived equivalent viscous damping is inversely proportional to the motion amplitude and excitation frequency. The characteristic stick-slip of dry friction is dominant at small amplitude dynamic loads leading to a hardening effect (stiffening) of the FB structure. The operating temperature produces shaft growth generating a bearing preload. However, the temperature does not significantly affect the identified FB parameters, albeit the experimental range was too small considering the bearings intended use in industry.

scholarly journals Asymmetric and chaotic responses of dry friction oscillators with different static and kinetic coefficients of friction

Meccanica ◽  
2021 ◽  
Author(s):  
Gábor Csernák ◽  
Gábor Licskó
Keyword(s):  
Dry Friction ◽  
Continuation Method ◽  
Friction Model ◽  
Lugre Friction Model ◽  
Kinetic Coefficients ◽  
Friction Oscillator ◽  
Lugre Friction ◽  
Friction Parameters ◽  
Two Parameter ◽  
Parameter Bifurcation

AbstractThe responses of a simple harmonically excited dry friction oscillator are analysed in the case when the coefficients of static and kinetic coefficients of friction are different. One- and two-parameter bifurcation curves are determined at suitable parameters by continuation method and the largest Lyapunov exponents of the obtained solutions are estimated. It is shown that chaotic solutions can occur in broad parameter domains—even at realistic friction parameters—that are tightly enclosed by well-defined two-parameter bifurcation curves. The performed analysis also reveals that chaotic trajectories are bifurcating from special asymmetric solutions. To check the robustness of the qualitative results, characteristic bifurcation branches of two slightly modified oscillators are also determined: one with a higher harmonic in the excitation, and another one where Coulomb friction is exchanged by a corresponding LuGre friction model. The qualitative agreement of the diagrams supports the validity of the results.

Energy Balancing Method to Identify Nonlinear Damping of Bolted-Joint Interface

2016 ◽  
Vol 693 ◽  
pp. 318-323 ◽  
Author(s):  
Xin Liao ◽  
Jian Run Zhang
Keyword(s):  
Dry Friction ◽  
Harmonic Excitation ◽  
Joint Interface ◽  
Damping Factor ◽  
Viscous Damping ◽  
Bolted Joint ◽  
Energy Balancing ◽  
Stick Slip ◽  
Non Linear ◽  
Linear Damping

The interface of bolted joint commonly focuses on the research of non-linear damping and stiffness, which affect structural response. In the article, the non-linear damping model of bolted-joint interface is built, consisting of viscous damping and Coulomb friction. Energy balancing method is developed to identify the dry-friction parameter and viscous damping factor. The corresponding estimation equations are acquired when the input is harmonic excitation. Then, the vibration experiments with different bolted preloads are conducted, from which amplitudes in various input levels are used to work out the interface parameters. Also, the fitting curves of dry-friction parameters are also obtained. Finally, the results illustrate that the most interface of bolted joint in lower excitation levels occurs stick-slip motion, and the feasibility of the identification approach is demonstrated.

Design and structural performance measurements of a novel multi-cantilever foil bearing

2014 ◽  
Vol 229 (10) ◽  
pp. 1830-1838 ◽  
Author(s):  
Kai Feng ◽  
Xueyuan Zhao ◽  
Zhiyang Guo
Keyword(s):  
Dynamic Characteristics ◽  
Dynamic Load ◽  
Dynamic Stiffness ◽  
Excitation Frequency ◽  
Viscous Damping ◽  
Equivalent Viscous Damping ◽  
Foil Bearing ◽  
Load Tests ◽  
Stiffness And Damping ◽  
Motion Amplitude

With increasing need for high-speed, high-temperature, and oil-free turbomachinery, gas foil bearings (GFBs) have been considered to be the best substitutes for traditional oil-lubricated bearings. A multi-cantilever foil bearing (MCFB), a novel GFB with multi-cantilever foil strips serving as the compliant underlying structure, was designed, fabricated, and tested. A series of static and dynamic load tests were conducted to measure the structural stiffness and equivalent viscous damping of the prototype MCFB. Experiments of static load versus deflection showed that the proposed bearing has a large mechanical energy dissipation capability and a pronounced nonlinear static stiffness that can prevents overly large motion amplitude of journal. Dynamic load tests evaluated the influence of motion amplitude, loading orientation and misalignment on the dynamic stiffness and equivalent viscous damping with respect to excitation frequency. The test results demonstrated that the dynamic stiffness and damping are strongly dependent on the excitation frequency. Three motion amplitudes were applied to the bearing housing to investigate the effects of motion amplitude on the dynamic characteristics. It is noted that the bearing dynamic stiffness and damping decreases with incrementally increasing motion amplitudes. A high level of misalignment can lead to larger static and dynamic bearing stiffness as well as to larger equivalent viscous damping. With dynamic loads applied to two orientations in the bearing midplane separately, the dynamic stiffness increases rapidly and the equivalent viscous damping declines slightly. These results indicate that the loading orientation is a non-negligible factor on the dynamic characteristics of MCFBs.

Modelling and Analysis of a Grout Delivery Mechanism in the Remote Spray Lining of Shafts

1996 ◽  
Author(s):  
Liu Hongzhao ◽  
E. Appleton
Keyword(s):  
Relative Velocity ◽  
Viscous Friction ◽  
Emission Angle ◽  
Inertia Force ◽  
Viscous Damping ◽  
Friction Forces ◽  
Viscous Friction Force ◽  
Full Discussion ◽  
Delivery Mechanism ◽  
Driving Torque

Abstract A thorough analysis on the characteristics of a grout delivery mechanism in the lining of shafts has been accomplished. The dynamic equation of this spraying mechanism has been established and can describe the system’s performance properties under different conditions of viscous friction forces. The analysis introduces a combined viscous damping coefficient c* and a ratio λ between viscous friction force and inertia force. It is proved theoretically that the relative velocity of the grout is less than the implicate velocity and the emission angle α described in the paper is always larger than 45 °. Numerical simulations are performed by feeding various different parameters into the model. A full discussion of the effects of different variables is presented. Additionally, a formula for calculating the driving torque and power is developed. These studies provide an understanding of the properties of this mechanism and should prove useful in guiding its design and operation.

Experimental Evaluation of the Structure Characterization of a Novel Hybrid Bump-Metal Mesh Foil Bearing

2015 ◽  
Vol 138 (2) ◽  
Author(s):  
Kai Feng ◽  
Yuman Liu ◽  
Xueyuan Zhao ◽  
Wanhui Liu
Keyword(s):  
Excitation Frequency ◽  
Structure Characterization ◽  
Viscous Damping ◽  
Metal Mesh ◽  
Equivalent Viscous Damping ◽  
Foil Bearings ◽  
Damping Characteristics ◽  
Foil Bearing ◽  
Mesh Density ◽  
Load Tests

Rotors supported by gas foil bearings (GFBs) experience stability problem caused by subsynchronous vibrations. To obtain a GFB with satisfactory damping characteristics, this study presented a novel hybrid bump-metal mesh foil bearing (HB-MMFB) that consists of a bump foil and metal mesh blocks in an underlying supporting structure, which takes advantage of both bump-type foil bearings (BFBs) and MMFBs. A test rig with a nonrotating shaft was designed to estimate structure characterization. Results from the static load tests show that the proposed HB-MFBs exhibit an excellent damping level compared with the BFBs with a similar size because of the countless microslips in the metal mesh blocks. In the dynamic load tests, the HB-MFB with a metal mesh density of 36% presents a viscous damping coefficient that is approximately twice that of the test BFB. The dynamics structural coefficients of HB-MFBs, including structural stiffness, equivalent viscous damping, and structural loss factor, are all dependent on excitation frequency and motion amplitude. Moreover, they exhibit an obvious decrease with the decline in metal mesh density.

Sign in / Sign up

Export Citation Format

Share Document