A Numerical Study on the Effects of Unsteady Wind on Vertical Axis Wind Turbine Performance

2013 ◽  
Author(s):  
Louis Angelo Danao ◽  
Jonathan Edwards ◽  
Okeoghene Eboibi ◽  
Robert Howell
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Numerical Study ◽  
Angle Of Attack ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Peak Performance ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Tip Speed Ratio

Numerical simulations using RANS–based CFD have been utilised to carry out investigations on the effects of unsteady wind in the performance of a wind tunnel vertical axis wind turbine. Using a validated CFD model, unsteady wind simulations revealed a fundamental relationship between instantaneous VAWT CP and wind speed. CFD data shows a CP variation in unsteady wind that cuts across the steady CP curve as wind speed fluctuates. A reference case with mean wind speed of 7m/s, wind speed amplitude of ±12%, fluctuating frequency of 0.5Hz and mean tip speed ratio of 4.4 has shown a wind cycle mean power coefficient of 0.33 that equals the steady wind maximum. Increasing wind speed causes the instantaneous tip speed ratio to fall which leads to higher effective angle of attack and deeper stalling on the blades. Stalled flow and rapid changes in angle of attack of the blade induce hysteresis loops in both lift and drag. Decreasing wind speeds limit the perceived angle of attack seen by the blades to near static stall thus reducing the positive effect of dynamic stall on lift generation. Three mean tip speed ratio cases were tested to study the effects of varying conditions of VAWT operation on the overall performance. As the mean tip speed ratio increases, the peak performance also increases.

Numerical Research on the Characteristics of Lift-Drag Type Vertical Axis Wind Turbine

2012 ◽  
Vol 189 ◽  
pp. 448-452
Author(s):  
Yan Jun Chen ◽  
Guo Qing Wu ◽  
Yang Cao ◽  
Dian Gui Huang ◽  
Qin Wang ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Vertical Axis ◽  
Chord Length ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Tip Speed Ratio ◽  
Middle Range ◽  
Parabolic Form ◽  
Cfd Method

Numerical studies are conducted to research the performance of a kind of lift-drag type vertical axis wind turbine (VAWT) affected by solidity with the CFD method. Moving mesh technique is used to construct the model. The Spalart-Allmaras one equation turbulent model and the implicit coupled algorithm based on pressure are selected to solve the transient equations. In this research, how the tip speed ratio and the solidity of blade affect the power coefficient (Cp) of the small H-VAWT is analyzed. The results indicate that Cp curves exhibit approximate parabolic form with its maximum in the middle range of tip speed ratio. The two-blade wind turbine has the lowest Cp while the three-blade one is more powerful and the four-blade one brings the highest power. With the certain number of blades, there is a best chord length, and too long or too short chord length may reduce the Cp.

Experimental Study of Vertical Axis Wind Turbine with Wind Speed Self-Adapting

2012 ◽  
Vol 215-216 ◽  
pp. 1323-1326
Author(s):  
Ming Wei Xu ◽  
Jian Jun Qu ◽  
Han Zhang
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Wind Velocity ◽  
Vertical Axis ◽  
Maximum Power ◽  
The Self ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Opening And Closing

A small vertical axis wind turbine with wind speed self-adapting was designed. The diameter and height of the turbine were both 0.7m. It featured that the blades were composed of movable and fixed blades, and the opening and closing of the movable blades realized the wind speed self-adapting. Aerodynamic performance of this new kind turbine was tested in a simple wind tunnel. Then the self-starting and power coefficient of the turbine were studied. The turbine with load could reliably self-start and operate stably even when the wind velocity was only 3.6 m/s. When the wind velocity was 8 m/s and the load torque was 0.1Nm, the movable blades no longer opened and the wind turbine realized the conversion from drag mode to lift mode. With the increase of wind speed, the maximum power coefficient of the turbine also improves gradually. Under 8 m/s wind speed, the maximum power coefficient of the turbine reaches to 12.26%. The experimental results showed that the new turbine not only improved the self-starting ability of the lift-style turbine, but also had a higher power coefficient in low tip speed ratio.

scholarly journals Kontrol Angle of Attack untuk Optimasi Daya padaVertical Axis Wind Turbine Tipe Darrieus

2020 ◽  
Vol 8 (3) ◽  
pp. 492
Author(s):  
WAHYU AULIA NURWICAKSANA ◽  
BUDHY SETIAWAN ◽  
IKA NOER SYAMSIANA ◽  
SEPTYANA RISKITASARI
Keyword(s):  
Wind Turbine ◽  
Angle Of Attack ◽  
Vertical Axis ◽  
Speed Ratio ◽  
Trial And Error ◽  
Proportional Integral Derivative ◽  
Vertical Axis Wind Turbine ◽  
Average Efficiency ◽  
Proportional Integral ◽  
Tip Speed Ratio

ABSTRAKVAWT (Vertical Axis Wind Turbine) tipe Darrieus NACA0015 merupakan salah satu model dari turbin angin yang bekerja dengan menggunakan angin sebagai sumber penggerak. Namun dari hasil pengamatan, kecepatan angin yang ada tidak konstan setiap saat. Sehingga dari permasalahan ini perlu suatu kontrol yaitu dengan mengendalikan sudut kerja blade VAWT yang dikenal dengan kontrol angle of attack (AoA). Prinsip kerja kontrol AoA yaitu sudut blade diatur agar VAWT bekerja secara optimum dan dapat meningkatkan efisiensi. Metode kontrol AoA menggunakan PID (Proportional–Integral–Derivative) dengan memberikan nilai trial and error pada Kp, Ki, Kd. VAWT ini menggunakan konstanta TSR (Tip Speed Ratio) yaitu 4. Hasil dari penelitian ini yaitu daya yang dihasilkan VAWT dengan kontrol AoA mendapatkan rata-rata efisiensi sebesar 5.16%, sedangkan VAWT tanpa kontrol mendapatkan efisiensi sebesar 3.49%. Sehingga dapat disimpulkan bahwa dengan kontrol AoA, rata-rata efisiensi dayanya naik sebesar 1.67% dari yang tanpa kontrol.Kata Kunci: Kontrol Angle of Attack (AoA), VAWT, TSR, Efisiensi ABSTRACTVAWT (Vertical Axis Wind Turbine) type Darrieus NACA0015 is one model of a wind turbine that works by using wind as a source of propulsion. Conditions from observations, wind speeds that are not constant every time. So from this problem needs control VAWT by controlling the working angle of the VAWT blade is the angle of attack control (AoA). The principle AoA control is that the blade angle adjusted so that the VAWT works optimally and can improve the efficiency. AoA control method uses PID (Proportional-Integral-Derivative) by providing trial and error values for Kp, Ki, Kd. VAWT uses TSR (Tip Speed Ratio) constant which is 4. The results of this research, VAWT with AoA control get an average efficiency of 5.16%, while without control gets an average efficiency of 3.49%. So it can be concluded that with AoA control, the average power efficiency increases by 1.67% from those without control.Keywords: Angle of Attack (AoA) Control, VAWT, TSR, Efficiency

scholarly journals Determination Method of Critical Best Tip Speed Ratio for the Vertical Axis Wind Turbine

2015 ◽  
Vol 9 (1) ◽  
pp. 320-323
Author(s):  
Zhang Lijun ◽  
Liu Hua ◽  
Zhang Mingming ◽  
Hu Yi’e
Keyword(s):  
Wind Turbine ◽  
Lift Coefficient ◽  
Tangential Force ◽  
Angle Of Attack ◽  
Vertical Axis ◽  
Position Angle ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Tip Speed Ratio ◽  
The Relationship

Tip speed ratio is an important parameter of describing wind turbine performance. Based on vane airfoil profile, the relationship between vane lift coefficient, drag coefficient and angle of attack is calculated by means of Profili software. The corresponding stall angle is also obtained. The relationship between the position angle of vane and angle of attack at different tip speed ratios is drawn by Matlab software and the corresponding best tip speed ratio is determined rapidly. Based on it, the airfoil tangential force is also analyzed for different vane airfoil profiles in the condition of same Reynolds number.

Performance Improvements for a Vertical Axis Wind Turbine by Means of Gurney Flap

2019 ◽  
Vol 142 (2) ◽  
Author(s):  
Yan Yan ◽  
Eldad Avital ◽  
John Williams ◽  
Jiahuan Cui
Keyword(s):  
Wind Turbine ◽  
Stokes Equations ◽  
Numerical Study ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Navier Stokes ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Performance Improvements ◽  
Gurney Flap

Abstract A numerical study was carried out to investigate the effects of a Gurney flap (GF) on the aerodynamics performance of the NACA 00 aerofoil and an associated three-blade rotor of a H-type Darrieus wind turbine. The flow fields around a single aerofoil and the vertical axis wind turbine (VAWT) rotor are studied using unsteady Reynolds-averaged Navier–Stokes equations (URANS). The height of GF ranges from 1% to 5% of the aerofoil chord length. The results show that the GF can increase the lift and lift-to-drag ratio of the aerofoil as associated with the generation of additional vortices near the aerofoil trailing edge. As a result, adding a GF can significantly improve the power coefficient of the VAWT at low tip speed ratio (TSR), where it typically gives low power production. The causing mechanism is discussed in detail, pointing to flow separation and dynamic stall delay.

scholarly journals Performance of a Small-sized Savonious Blade with Wind Concentrator

2018 ◽  
Vol 10 (3) ◽  
pp. 1227
Author(s):  
Dygku. Asmanissa Awg. Osman ◽  
Norzanah Rosmin ◽  
Aede Hatib Mustaamal ◽  
Siti Maherah Hussin ◽  
Md Pauzi Abdullah
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Experimental Testing ◽  
Electrical Power ◽  
Vertical Axis ◽  
Angular Speed ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Air Compressor ◽  
Tip Speed Ratio

<span>This paper presents the performance of a fabricated small-sized Savonious wind turbine with two blades. The design of Savonius vertical axis wind turbine (VAWT) was based on Malaysia wind speed condition. Meanwhile, the design of wind concentrator was based on the dimensions and the constant airflow of an air compressor. From the experimental testing in a laboratory, it was found that the proposed Savonious turbine has best performance when tested using wind concentrator. To conclude, airflow from air compressor can be increased when the proposed wind concentrator is used and hence increasing the proposed VAWT performance in terms of its angular speed (ω), tip speed ratio (TSR) and the generated electrical power (PE).</span>

scholarly journals Studi simulasi penggunaan airfoil naca 6412 sebagai sudu pada turbin angin crossflow melalui pemodelan CFD 2 dimensi

2018 ◽  
Vol 13 (1) ◽  
pp. 28
Author(s):  
Muhammad Ivan Fadhil Hendrawan ◽  
Dominicus Danardono ◽  
Syamsul Hadi
Keyword(s):  
Wind Turbine ◽  
Constant Velocity ◽  
Cross Flow ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Ansys Fluent ◽  
Tip Speed Ratio ◽  
Blade Number

AbstractThe simulation aimed to understand the effect of the angle of blade number and blade number of vertical axis wind turbine with cross flow runner to enhance the performance of wind turbine. The turbine had 20, 22, and 24 number of blades. Simulation was done in 2D analysis using ANSYS-Fluent. Tip speed ratio was varied in range of 0,1-0,5 with constant velocity inlet 2 m/s. The effect of blade numbers to torque and power coefficient were analyzed and compared. It had been found that the best power coefficient were 0,5 at tip speed ratio 0,3.

scholarly journals Studi Eksperimen Pengaruh Jumlah Sudu Terhadap Kinerja Wind Turbine Crossflow

2021 ◽  
Vol 16 (2) ◽  
pp. 218
Author(s):  
Fahrudin Fahrudin ◽  
Fitri Wahyuni ◽  
Dini Oktavitasari
Keyword(s):  
Wind Turbine ◽  
Alternative Energy ◽  
Wind Tunnel Test ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Test Scheme ◽  
Vertical Axis Wind Turbine ◽  
Tip Speed Ratio ◽  
Torque Coefficient

<p>Wind is an alternative energy that is environmentally friendly and sustainable. Therefore, we need a type of wind turbine that can receive wind from all directions. The crossflow type vertical axis wind turbine has a high torque coefficient at a low tip speed ratio. The purpose of this study was to determine the effect of the number of blades on the performance of the vertical axis crossflow wind turbine. The experimental test was carried out by varying the number of blades. The configuration is analyzed using the experimental wind tunnel test scheme which has been modified in the section test section. The results showed that the number of blades 16 has a power coefficient ( ) = 0.23 tip speed ratio (TSR) = 0.42 at a wind speed of 4 m / s.</p><p><strong><br /></strong></p>

scholarly journals Dynamic Stall of a Vertical-Axis Wind Turbine and Its Control Using Plasma Actuation

Energies ◽  
2019 ◽  
Vol 12 (19) ◽  
pp. 3738 ◽  
Author(s):  
Lu Ma ◽  
Xiaodong Wang ◽  
Jian Zhu ◽  
Shun Kang
Keyword(s):  
Wind Turbine ◽  
Tangential Force ◽  
Vertical Axis ◽  
Dynamic Stall ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Dbd Plasma ◽  
Tip Speed Ratio ◽  
Plasma Actuation

In this paper, a dynamic stall control scheme for vertical-axis wind turbine (VAWT) based on pulsed dielectric-barrier-discharge (DBD) plasma actuation is proposed using computational fluid dynamics (CFD). The trend of the wind turbine power coefficient with the tip speed ratio is verified, and the numerical simulation can describe the typical dynamic stall process of the H-type VAWT. The tangential force coefficient and vorticity contours of the blade are compared, and the regular pattern of the VAWT dynamic stall under different tip speed ratios is obtained. Based on the understanding the dynamic stall phenomenon in flow field, the effect of the azimuth of the plasma actuation on the VAWT power is studied. The results show that the azimuth interval of the dynamic stall is approximately 60° or 80° by the different tip speed ratio. The pulsed plasma actuation can suppress dynamic stall. The actuation is optimally applied for the azimuthal position of 60° to 120°.

scholarly journals Experimental Study of Wind Booster Addition for Savonius Vertical Wind Turbine of Two Blades Variations Using Low Wind Speed

2019 ◽  
Vol 125 ◽  
pp. 14003
Author(s):  
Eflita Yohana ◽  
MSK. Tony Suryo U ◽  
Binawan Luhung ◽  
Mohamad Julian Reza ◽  
M Badruz Zaman
Keyword(s):  
Wind Speed ◽  
Wind Energy ◽  
Wind Turbine ◽  
Vertical Axis ◽  
Vertical Wind ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Tip Speed Ratio ◽  
Average Value ◽  
Low Wind Speed

The Wind turbine is a tool used in Wind Energy Conversion System (WECS). The wind turbine produces electricity by converting wind energy into kinetic energy and spinning to produce electricity. Vertical Axis Wind Turbine (VAWT) is designed to produce electricity from winds at low speeds. Vertical wind turbines have 2 types, they are wind turbine Savonius and Darrieus. This research is to know the effect of addition wind booster to Savonius vertical wind turbine with the variation 2 blades and 3 blades. Calculation the power generated by wind turbine using energy analysis method using the concept of the first law of thermodynamics. The result obtained is the highest value of blade power in Savonius wind turbine without wind booster (16.5 ± 1.9) W at wind speed 7 m/s with a tip speed ratio of 1.00 ± 0.01. While wind turbine Savonius with wind booster has the highest power (26.3 ± 1.6) W when the wind speed of 7 m/s with a tip speed ratio of 1.26 ± 0.01. The average value of vertical wind turbine power increases Savonius after wind booster use of 56%.

Sign in / Sign up

Export Citation Format

Share Document